Time for me to upgrade ??

[lotsip]

Re: Time for me to upgrade ??

that did it, raised the DVid to +.04375 (next possible choice) and LinX successfully ran 3 passes at HT on, 4096mbs., 8 threads, 47, 47 and 47 GFlops, and good temps.

now what....?

[Chike]

Re: Time for me to upgrade ??

4 and and 6 threads? And CINEBENCH.
I forgot normal
vcore, hwo much is it total?

[lotsip]

Re: Time for me to upgrade ??

normal voltage is 1.168........so, if i got this right, normal 1.168 + dvid .04375= 1.21V......temps seemed good running Linx though....kept my eye on them and afterwards i ran linx and ibt at 4096, 8 threads, with easy tune and cpu-z ONLY to watch the voltage........both were steady at "1.2v".........again, temps seem ok to me......highest i have seen at any point today is mid 60's, and no load like 22 or 24....

ya, i did 4 and 6 earlier , they were ok with dvid +0375v, passing linx with three passes...........should I run em again with the new +.04375 voltage ?.......they should be fine right ?

haven't run cinebench since this morning...........god, this stuff gets u dizzy after a while....lol.........

[wazza300]

Re: Time for me to upgrade ??

You'll see the difference multithreading makes in cinebench CPU test,much higher scores with mt enabled

[lotsip]

Re: Time for me to upgrade ??

ya, just ran cinebench again, wow........6.26 pts......this morning, with the old 3.36mhz, 1600 oc, cinebench was 4.46 ht off, and 5.70 ht
thanks so much ~~~!!!!

[wazza300]

Re: Time for me to upgrade ??

That's why I said keep it enabled,just disable it for ibt as you get higher gflops

[lotsip]

Re: Time for me to upgrade ??

thanks wazza........

funny, for the past few days, i've felt like i'm on the episode of Seinfeld, where Kramer had the car dealer on a test drive with a car running out of gas.........more more..........should we stop.?.....nooooooooo, i think we can go further !, lol haha, ok, i need a nap, i am OD'd on OCing at the moment...

thanks guys ! back in a while ;))

[Chike]

Re: Time for me to upgrade ??

The 6 and 8 threads LinX just to see if they have been improved after you raised DVID.

The way it looks there's no need for you to upgrade yet

[Chike]

Re: Time for me to upgrade ??

You can compare CINBENCH scores 3D Fluff Maxon Cinebench 11.5 Score Results
Looks right compared to similar systems OCed to the same level.

[lotsip]

Re: Time for me to upgrade ??

Cinebench CPU = 6.32 ;)............ok, goin to rerun LinX 6 and 8 threads.....wait, didn't i do that with thise OC yet ? I'd look at my notes, but, the pile of paper is too confusing now lol and ya, looks like you saved me some big bucks ! lol

[lotsip]

Re: Time for me to upgrade ??

;-))

[wazza300]

Re: Time for me to upgrade ??

Is that at 3.6? Push for 4ghz,your temps are good still

[lotsip]

Re: Time for me to upgrade ??

Is that at 3.6? Push for 4ghz,your temps are good still

yes, 3.68mhz..........and hehe, sounds good to me, this is fun ;) and ya, haven't hit 70 yet on any of the benchmarks, no load windows temps in the mid 20's.

[lotsip]

Re: Time for me to upgrade ??

4 and and 6 threads? And CINEBENCH.
I forgot normal
vcore, hwo much is it total?

4 and 6 threads , HT on, bout the same as before

[Darkje]

Re: Time for me to upgrade ??

my oc-ed 2500k will do about 7.10pts cpu @ 4500mhz, so that would be a nice target for you ;)...