GIGABYTE Latest Beta BIOS

[hsn]

i am using aorus b550i (f13a) + patriot 4400mhz. i can boot with fclk 2066 and ram run at 4133mhz. when i use TM5 and press start, there is a very loud noise in my speaker. and it doesn't stop at all, unless I press exit the sound will disappear. looks like this happened while it was loading. when there is a win 10 notification sound, the sound coming out of the headphones will be choppy.

When the default setting of xmp is disabled and my ram runs at 2133, there is no noise when the pc is idle or loaded.

previously I used bios f11-f12 there was no noise at all, either idle or load. either the default condition or boot at fclk 1900.

Is there a manual setting so that the sound does not appear?

thank you

[jwsg]

Windows installed 10.39.212.2020 for me (2020) - perhaps this is "Realtek Gaming 2.5Gb Family Controller" and the 2015 driver is "Realtek PCIe 2.5Gb Family Controller" - but in any case it is also satisfactory.

The insoluble problem is the Bluetooth module disappearing - I'm trying out a cheap BT 5 USB

[destruya]

Any hint of a change log for the F9K Z390 Xtreme BIOS?

Also, thank you for keeping this page up.

[Marucins]

legendos / Marucins - I'm really not sure why, but it would be really helpful if you guys could both make tickets with Gigabyte mentioning the issue as a LOT of people seem to have similar problems!

https://esupport.gigabyte.com/

This is not a mistake. There is nothing to report here. You completely don't understand how it works.
Your processor has limitations, you've just come across them. These limitations were generally discussed by AMD during the presentation.

How do you want it to work buy another RAM. Buy 4 memory dice right away, where each of them will be SingleRank. Then you'll have your 3800 CL anyway.

How do you want to embrace what you have now download the program to OC RAM and set your preferences, ale nie wi?cej jak 3733. Rewrite exactly the same settings into the bios.

You will have more than JEDEC.

[wisebear]

stasio Do you know if AMD has been working on or has distributed a new AGESA version to the motherboard manufacturers? Should we expect new BIOS releases this week?

[chinmoy32]

Any hint of a change log for the F9K Z390 Xtreme BIOS?

Also, thank you for keeping this page up.

They means the Gigabyte Tech Support, supposed to fix the 10 Gig lan disable option fixed (which was broken on F9j) on the F9k, but they botched that too. so there is nothing changed on the F9k from the F9j BIOS as far as I know. I immediately tested the F9k and raised another ticket on the tech support site and also uploaded it here and mentioned stasio in the post. As the Chinese new year holidays are going on I guess they will respond soon after office opens.

[FedeS]

Windows installed 10.39.212.2020 for me (2020) - perhaps this is "Realtek Gaming 2.5Gb Family Controller" and the 2015 driver is "Realtek PCIe 2.5Gb Family Controller" - but in any case it is also satisfactory.

The insoluble problem is the Bluetooth module disappearing - I'm trying out a cheap BT 5 USB

these motherboards are junk
they have been on the market since June 2020 and until today (8 months) no problems have been fixed and at this point they probably never will
P.S. don't tell me that the other brands are like that because I'm using an asus in person and it has no flaws like the gigabyte

[Kirill_24_02_1988]

these motherboards are junk
they have been on the market since June 2020 and until today (8 months) no problems have been fixed and at this point they probably never will
P.S. don't tell me that the other brands are like that because I'm using an asus in person and it has no flaws like the gigabyte

That's right (they completely scored on users and the bugs in some places are ridiculous ... unlike Gigabyte, ASUS is more loyal to the consumer)

[jeffk]

I'm using 10.46 network driver, and I stil had issue that the eth is going down with no log in Windows Journal.

I disabled 80% of the settings in the device property, now its not disconnecting anymore. I cant tell which one is doing the ticks so...

[DanHot]

these motherboards are junk
they have been on the market since June 2020 and until today (8 months) no problems have been fixed and at this point they probably never will
P.S. don't tell me that the other brands are like that because I'm using an asus in person and it has no flaws like the gigabyte

Thats a LIE!
A had an ANUS Wix-E X570 and they have ErP Problems with WLAN+BT and so they removed this option and didnt fix the Problem.
Most problems come from the X570 chipset.
Next problem is that the communication under the vendors and amd is totally crap.
And the main problem are the stupid people sitting in the 1st lvl support. so all this problems cost a hole bunch of time, that the person who can fix it, reach the information 6 mounth later.
U all know silent post?!

[Drejfus]

these motherboards are junk
they have been on the market since June 2020 and until today (8 months) no problems have been fixed and at this point they probably never will
P.S. don't tell me that the other brands are like that because I'm using an asus in person and it has no flaws like the gigabyte

I have similar sentiments,
I'm switching from Elite to rog strix e-gaming

[FTorres]

FedeS well I cannot say they are junk but close to it they are, below some "bugs" in the B550 Aorus Master (F13a).

• There is always a voltage difference when setting voltage manually. (VSOC 1.1v on BIOS sets 1.116v on HWInfo CPU VCORE SoC and shows in SVI2 TFN as ~1.0875v)
• Some voltage only have offset options (VDDP and DDR VTT).
• Strange USB option for thunderbolt appears and if you load default presets it goes away.
• USB stills acts funny on another ports connected to the chipset, if you input into the ports connected to the CPU the problems go away (solution... bought an active USB hub to increase ports).
• Realtek 2.5G NIC strange behavior with latest drivers may fail in specific scenarios and loads (maybe related to the above, since it's connect to the chipset chip. solution... bought an USB 3.0 External NIC).
• Hard lock on GDM off with 1T above the standard specification (3400Mhz or 3466Mhz DRAM velocity), another stupid setting that will not let you boot to OS, you may think that is a RAM failure but it is not, it is hard locked to not boot on BIOS.
• CPPC and CPPC Preferred Cores is a mess on this BIOS, force enable or expect some weird **** happening.
• AGESA 1.2.0.0 should have a modern standby option already on, but this BIOS does not unlock it (fresh Windows install already tried).

Only correlation with the above may be related to the PCIe Gen bus used to communicate with the CPU setting this manually may help, not tried yet, but it is a cluster f... because the settings are not explained in detail.

Maybe I can find more bugs but please, I'm already at the point of selling this board and buy an MSi one really, they have already deployed a final stable 1.2.0.0 AGESA BIOS.

stasio if you can pass this info to the dev team when they come back to work it would be great I will open a support ticket also for awareness.

[thomasre]

these motherboards are junk
they have been on the market since June 2020 and until today (8 months) no problems have been fixed and at this point they probably never will
P.S. don't tell me that the other brands are like that because I'm using an asus in person and it has no flaws like the gigabyte

agree with you. Did Gigabyte even put out an official statement to all of these issues somewhere??

[Jaz69]

I have never had an issue with the latest Ethernet driver with aorus master x570 board i just didn't install the gigabyte one from their site. To begin with, I went to station drivers for all up to date drivers and they had the updated driver!.

To fix this you uninstall the gigabyte drivers add/remove the gigabyte one, use a reg cleaner like CCleaner to get rid of remaining drivers/software/broken links. reboot.
go to station drivers website before you uninstall and look for your motherboard then look for drivers. If its realtek it will be listed as an updated package to download and manually install. Also the gigabyte AMD CPU page drivers are way out of date. AMD have newer drivers out for power management etc which were listed on Station drivers and then on AMD main page.

https://station-drivers.com/index.php?option=com_content&view=category&id=11&Itemid=169&lang=en

Try it, works like a charm.

[AeroZ]

Does anybody else have PRD so off? Is it related to F12 BIOS or the Elite V2 board overall?