***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

[stasio]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

I got also one set 4x4GB Hynix CFR, 2200 pass no problem,higher I din't try yet.
Edit:
You can see my vtt and imc voltage on my last pic.

[profJim]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

I tried just about everything to get these to boot at 2400.
No one ever tells you how much vtt or imc voltage is need, they only show vdimm. WHY?????????

Check out page 6 in Samsung 30 nm Green PC3-12800 Low Profile 1.35 V DDR3 Review | techPowerUp.
I think that there were a few other recommended settings in their review.

[wazza300]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***



heres the settings i use for 2133mhz and vtt/dram ect for anyone wanting to try,super pi 32m stable also

[stasio]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

It's very unusual to see ASUS UEFI in this forum......

btw,.....(PI32 pass)

[Acebmxer]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

Yeah Wazza is a traitor and left Gigabyte for Asus

btw nice Stasio. I wish I could push my gskills past 2200 or samsung past 2133.

Gskill no error peeps just post codes 15 and 03 and system reboot with overclock failed message. Samsung like 30 short beeps and dont remember what post code then reboot with overclock failed message.

[2therock]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

I wish someone would give me $50.00 for my 4x4GB Sammy Green shipped.

[Octopuss]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

My question got a bit buried down the pages, so I will take the opportunity to ask again: anyone ever had problem with front USB ports, going from F_USB30 "double connector" on UD3H? Only the right one works, other is completely dead. It might be the bay, but I don't think so as I only just upacked it at the same time I assembled the PC.

[2therock]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

Swap the cables and see if the issue follows.

[wazza300]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

$50 shipped to England? And I'm sorry bout the asus but it was super cheap

[Octopuss]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

Swap the cables and see if the issue follows.

That's not technically possible, I am talking about the double connector. You don't connect two separate cables to it.

[wazza300]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

That's not technically possible, I am talking about the double connector. You don't connect two separate cables to it.

have you checked the cable at the plug end? just to makesure no holes are damaged ect,same thing for the usb3 socket on the mb,make sure no pins are bent,it should work with both usb3 sockets not just one,if it still doesnt work email gigabyte and ask for replacement usb3 caddy

[Octopuss]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

For replacement of what? I don't understand. I bought this Akasa 3.5" bay with two USB ports and room for 2.5" HDD inside.

[wazza300]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

For replacement of what? I don't understand. I bought this Akasa 3.5" bay with two USB ports and room for 2.5" HDD inside.

ahh sorry i thought that board came with a usb3 caddy like the ud5 does,idk why both ports arnt working

[boondocks]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

@Octopuss I don't know about the UD3H, I don't have any problems with USB 3.0 on my UD5H boards. Might want to contact Gigabyte since you're obviously not getting an answer here. I did bend a pin on one of the headers once and it was really hard to see, but I was able to straighten it.

[Acebmxer]

Re: ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***

The UD3H only has 1 USB 3.0 front panel header and does not come with a USB3 caddy for front panel usb3. It would have to be supplied by the case MFR or aftermarket.

@Octopuss if you have not already check that the pins are not bent. I would say try to RMA the front panel USB caddy first before RMAing the motherboard.