Re: GA-EP45-UD3P - Won't boot with 450FSB
This is my "Basic Settings" template using what you advised PJ...
I think Memtest86+ is pretty happy...
This is my "Basic Settings" template using what you advised PJ...
Code:
************************************* ************************************* Gigabyte GA-EP45-UD3P (Rev. 1.0) - F9 ************************************* ************************************* ****************************** MB Intelligent Tweaker(M.I.T.) ****************************** Robust Graphics Booster ..............: [Auto] CPU Clock Ratio ......................: [9X] x Fine CPU Clock Ratio................: +0.0 CPU Frequency ........................: 3.00GHz( 333x9) ********** Clock Chip Control ******** >>>>> Standard Clock Control CPU Host Clock Control................: [Disabled] x CPU Host Frequency(Mhz).............: 333 PCI Express Frequency(Mhz)............: [100] C.I.A.2...............................: [Disabled] >>>>> Advanced Clock Control..........: [Press Enter] CPU Clock Drive.......................: [800mV] PCI Express Clock Drive...............: [900mV] CPU Clock Skew........................: [ 0ps] MCH Clock Skew........................: [ 0ps] ******** DRAM Performance Control ******** Performance Enhance...................: [Turbo] Extreme Memory Profile(X.M.P.)........: [Disabled] (G)MCH Frequency Latch................: [Auto] System Memory Multiplier (SPD)........: [Auto] Memory Frequency(Mhz).....800.........: 800 DRAM Timing Selectable (SPD)..........: [Auto] >>>>> Standard Timing Control x CAS Latency Time................5...: Auto x tRCD ...........................5...: Auto x tRP.............................5...: Auto x tRAS...........................18...: Auto >>>>> Advanced Timing Control.........: [Press Enter] x tRRD............................3...: Auto x tWTR............................3...: Auto x tWR.............................6...: Auto x tRFC...........................52...: Auto x tRTP............................3...: Auto x Command Rate (CMD) .............0...: Auto >>>>> Channel A Timing Settings.......: [Press Enter] x Static tRead Value..............8...: Auto x tRD Phase0 Adjustment...........1...: Auto x tRD Phase1 Adjustment...........1...: Auto x tRD Phase2 Adjustment ..........1...: Auto x tRD Phase3 Adjustment...........1...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel A Driving Settings......: [Press Enter] x Driving Strength Profile............: Auto x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto >>>>> Channel B Timing Settings.......: [Press Enter] x Static tRead Value..............8...: Auto x tRD Phase0 Adjustment...........1...: Auto x tRD Phase1 Adjustment...........1...: Auto x tRD Phase2 Adjustment ..........1...: Auto x tRD Phase3 Adjustment...........1...: Auto x Trd2rd(Different Rank)..........6...: Auto x Twr2wr(Different Rank)..........6...: Auto x Twr2rd(Different Rank)..........5...: Auto x Trd2wr(Same/Diff Rank)..........8...: Auto x DIMM1 Clock Skew Control (ps).......: Auto x DIMM2 Clock Skew Control (ps).......: Auto x DDR Write Training..................: Auto >>>>> Channel B Driving Settings......: [Press Enter] x Driving Strength Profile............: [Auto] x Data Driving Pull-Up Level..........: Auto x Cmd Driving Pull-Up level...........: Auto x Ctrl Driving Pull-Up Level..........: Auto x Clk Driving Pull-Up Level...........: Auto x Data Driving Pull-Down Level........: Auto x Cmd Driving Pull-Down level.........: Auto x Ctrl Driving Pull-Down Level........: Auto x Clk Driving Pull-Down Level.........: Auto ****** Motherboard Voltage Control ****** Voltage Types..........Normal...........Current ----------------------------------------------- >>> CPU Load-Line Calibration.................: [Disabled] CPU Vcore..............1.27500V.......: [1.27500V] CPU Termination........1.200V.........: [1.200V] CPU PLL................1.500V.........: [1.500V] CPU Reference..........0.760V.........: [Auto] >>> MCH/ICH MCH Core...............1.100V.........: [1.100V] MCH Reference..........0.760V.........: [Auto] MCH/DRAM Reference.....0.900V.........: [Auto] ICH I/O................1.500V.........: [1.500V] ICH Core...............1.100V.........: [1.100V] >>> DRAM DRAM Voltage...........1.800V.........: [2.000V] DRAM Termination.......0.900V.........: [Auto] Channel A Reference....0.900V.........: [Auto] Channel B Reference....0.900V.........: [Auto] ******** Advanced BIOS Features ******** Hard Disk Boot Priority...............: [Press Enter] First Boot Device.....................: [USB-HDD] Second Boot Device....................: [Hard Disk] Third Boot Device.....................: [CDROM] Password Check........................: [Setup] HDD S.M.A.R.T. Capability.............: [Enabled] Limit CPUID Max. to 3.................: [Disabled] No-Execute Memory Protect.............: [Enabled] CPU Enhanced Halt (C1E)...............: [Disabled] C2/C2E State Support..................: [Disabled] x C4/C4E State Support................: Disabled CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.....................: [Disabled] Virtualization Technology.............: [Disabled] Delay For HDD (Secs)..................: [ 0] Full Screen LOGO Show.................: [Disabled] Init Display First....................: [PEG] ******** Integrated Peripherals ******** USB Keyboard Function.................: [Enabled] USB Mouse Function....................: [Enabled] USB Storage Function..................: [Disabled]
Comment