Tweet
Re: GA-EP45-DS3R (e7200)
And boss, do you think that first i can try some better Ghz and then bring down settings?
Originally posted by Lsdmeasap
View Post
-
-
Re: GA-EP45-DS3R (e7200)
Yeah, you can leave those all set high until you find your CPU overclock you want, then lower them as you test for stability. Leave them high though, until you are sure you CPU is stable, that way when/if you get errors you know it is the CPU and not the ramComment
-
Re: GA-EP45-DS3R (e7200)
And please can you tell me what everything i have to increast for stable cpu? which voltages? and for what values +-?Originally posted by Lsdmeasap View PostComment
-
Re: GA-EP45-DS3R (e7200)
Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: 1.2-1.38 (Higher for higher FSB, I am using 1.34 for 450 FSB, but I am going to bring it down for sure.) 400 or so FSB, I would think 1.2-1.28 would be fine for you. May be even fine at stock value
CPU PLL…………………....1.500V*.......: <<<1.5-1.56
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)
Those are all the CPU Voltages, only you and your CPU can find what it stable. What CPU speed/FSB are you running and I will give you my best guess at a range to try outComment
-
Re: GA-EP45-DS3R (e7200)
Hello again, as usual i tryed lot of setups, and now i have 100% stable system. Here is my setup
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0.5
CPU Frequency ...........................: 3.41 (402*8.5=3417Mhz)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 402 Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................: 50
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 804
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3
tWR............................................ 3
tRFC........................................... 48
tRTP........................................... 3
Command Rate (CMD) ....................: 2
Driving Strength Profiles
Driving Strength ............................ 1066
Channel A
Static tRead Value.........................: 8
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................: 8
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
I was trying to decreast Voltage but it wasnt stable, so this is my final setup.
I want 3,6 but its unstable wit 1.4625 V in bios (something about 1.38V in CPUID) and im afraid to go higher.
Tell my your opinion please
And thank you for all advices and time:*Comment
-
Re: GA-EP45-DS3R (e7200)
Looks good, thanks for posting as it may help someone someday!
If you use a higher Termination and PLL you can maybe do 3.6 with less Vcore. Just giving you some thoughts on how to maybe get that goingComment
Comment