GA-EP45-DS3R (e7200)

[laker_faker]

Re: GA-EP45-DS3R (e7200)

dude, this temps are huge!!
You are using 1.29v (bios 1.35) this is so weird, is this new pc? u should clean some dirt.

Its new PC, its clean, with good cooler, so i dont know where is problem:/

[BongWizard]

Re: GA-EP45-DS3R (e7200)

Its new PC, its clean, with good cooler, so i dont know where is problem:/

did you apply the thermal paste properly? that's usually the reason for high temps when you've got a decent cooler on the CPU... also, you can probably lower the vcore to 1.3V (you really dont need 1.35 when you're at 3.16GHz) and if you can get stable at that voltage you should get much better temps...

next thing i gotta point out is Memory Performance Enhance should always be STANDARD when OCing and set your Static tRead to around 8-11.

but really man if you're getting those kinda temps at stock settings and voltages then you have something physically wrong with your setup... make sure your cooler is seated properly and that you dont have a massive cake of thermal paste on your chip... thermal paste is only to fill tiny gaps which arise from an imperfect finish on the cooler base, the layer should be absolutely tiny, less than paper thin

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

Memory Performance Enhance should always be STANDARD when OCing and set your Static tRead to around 8-11.

For sure

And please set PCI Express to 100, DO IT and stop messing around

You have to set your ram voltage to 2.0-2.1, and add some MCH Voltages

You should also be using the 333 MCH Strap, with 7-8 Static tRead. After 400 FSB use 400 MCH strap and 8-10 Static Tread.

Sounds like you are jumping around FAR too much, and not taking advantage of BIOS profiles. Save on the main Screen of the BIOS if F11, Load is F12

[laker_faker]

Re: GA-EP45-DS3R (e7200)

did you apply the thermal paste properly? that's usually the reason for high temps when you've got a decent cooler on the CPU... also, you can probably lower the vcore to 1.3V (you really dont need 1.35 when you're at 3.16GHz) and if you can get stable at that voltage you should get much better temps...

next thing i gotta point out is Memory Performance Enhance should always be STANDARD when OCing and set your Static tRead to around 8-11.

but really man if you're getting those kinda temps at stock settings and voltages then you have something physically wrong with your setup... make sure your cooler is seated properly and that you dont have a massive cake of thermal paste on your chip... thermal paste is only to fill tiny gaps which arise from an imperfect finish on the cooler base, the layer should be absolutely tiny, less than paper thin

Today i bought new thermal paste and use it, just tiny layer. Cooler is 100% correct setuped. i have front and back 120 mm fan so i raly dont know. maybe temperature indicators on motherboard are wrong, tomorrow i will test it with my hand, how hot is it:P

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

Do you maybe have your fans set to low for your cooler, or pointed wrong? What speeds do these fans run, and how are you controlling them?

[laker_faker]

Re: GA-EP45-DS3R (e7200)

Do you maybe have your fans set to low for your cooler, or pointed wrong? What speeds do these fans run, and how are you controlling them?

I think they are on maximum:/ I dont know how to control them

[laker_faker]

Re: GA-EP45-DS3R (e7200)

ok so i made a little test
i start OCCT, Speedfan and look for temperature
When it shows 70 C i touch it, it was cold, and graphic card shows 54 C and its hot
so there are two options (if im right):
1. temperature of cpu is ok but some temperature sensors are bad
2. there is some problem which incurred that cooler is cool but he doenst cool the cpu

my english realy sux:P

im sure that cooler is instaled correct, coz i was very focused, and with this belaying technologi isnt way to instal it bad and dont see it...

[laker_faker]

Re: GA-EP45-DS3R (e7200)

ok now i have this setup:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0.5
CPU Frequency ...........................: 3.41 (402*8.5=3417Mhz)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 402 Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0


DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 804
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 11

Advanced Timing Control
tRRD........................................... Auto
tWTR.......................................... Auto
tWR............................................ Auto
tRFC........................................... 60
tRTP........................................... Auto
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ............................ 800

Channel A
Static tRead Value.........................: 11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................: 11
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.35
CPU Termination…..... 1.200V*.......: 1.28
CPU PLL…………………....1.500V*.......: Auto
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………,,0.800V*.......: Auto

MCH/ICH
MCH Core…………….....1.100V...........: 1.2
MCH Reference….…….0.800V...........; Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.550V............: Auto
ICH Core…………...……1.100V............: Auto

DRAM
DRAM Voltage ……....1.800V............: 2.0
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

And just before OCCT end i got error message : CODE 4, it means: calculation error ("code 4 in one of the threads as even if the problem is memory/NB related, it will lead to calculation error")

Please have you some solution for me?

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

What does coretemp newest version show for you idle and load temps >>>
Core Temp

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

Yes, for the above, all those Auto settings can cause memory errors. And you may want to add a bit more MCH, and possibly set ram to 2.1 if your ram allows it

Could also be vcore. Only way to be SURE is to run memtest86+ with those exact settings for a few hours to be sure if it is your ram or not.

[laker_faker]

Re: GA-EP45-DS3R (e7200)

Yes, for the above, all those Auto settings can cause memory errors. And you may want to add a bit more MCH, and possibly set ram to 2.1 if your ram allows it

Could also be vcore. Only way to be SURE is to run memtest86+ with those exact settings for a few hours to be sure if it is your ram or not.

And please can you tell me some settings for these rams? Coz i dont know what i have to setup. i find settup 4-4-4-11 tRC 20 on 2V, or 4 4 4 12 tRC 22 on 2V.But i cant find tRC in bios settings. I think that 2,1 i cant make, coz everytime when i was trying to setup this, i cant get to windows.

Core Temp Shows max 71 C. But if are senzors on motherboard bad it will show this temperature in every software right?

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

trc is not in your BIOS. WOW, that is hot for a coretemp. What CPU Speed and voltage are you using?

We have given you settings, are you not getting anywhere or what? Just wonder what you have tried. I see you say you cannot get into windows, but I need to know why. So please post what you are trying (Full settings) and I will see if I can tell you why maybe it is failing

[laker_faker]

Re: GA-EP45-DS3R (e7200)

i tryed settings which you and wizard gave me here, i tryed settings from other topics, i tryed a lot of things, and today, i have stable setup, but only 3,21 ghz:( here it is:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.21 (402*8)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 402 Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 100
MCH Clock Skew (ps)...................: 150


DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 804
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12

Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 12
tWR............................................ 14
tRFC........................................... 60
tRTP........................................... 8
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ............................ 800

Channel A
Static tRead Value.........................: 10
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Channel B
Static tRead Value.........................: 10
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

I know that Vcore is high, but now i have stable setup what is perfect for me, but i dont know what now, which options i can decreast and how can i encreast Ghz to some stable value

[Dweirdo]

Re: GA-EP45-DS3R (e7200)

wow dude,u have the same settings as i had before i sent my board to fixing. and i had ep45-ds3r with E7300!!
it was stable exactly with this settings!i got it stable at 3.3ghz as well, i will post u back when i get my bpard back, and oc it to far more to 3.6 (if i succeed) cause maybe its a faulty mobo :S
these are the settings i used for 3.3:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.3 (413*8)(i used multiplier 10 but this is not the point here)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 413 Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 100, try this at 0
MCH Clock Skew (ps)...................: 150


DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 826
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 4/5
tRCD ......................................... 4/5
tRP'........................................... 4/5
tRAS.......................................... 12/15

Advanced Timing Control
tRRD........................................... 6
tWTR.......................................... 12
tWR............................................ 14
tRFC........................................... 60
tRTP........................................... 8
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ............................ 1066

Channel A
Static tRead Value.........................: 10
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Channel B
Static tRead Value.........................: 10
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

Both of you guys can now bring down some of those settings for sure >>>

(G)MCH Frequency Latch...............: 400

Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12

Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3-5
tWR............................................ 3-6
tRFC........................................... 48-54
tRTP........................................... 3-6
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ............................ 800 (1066 may work better)

Channel A & B
Static tRead Value.........................: 8-10