GA-EP45-DS3R (e7200)

[laker_faker]

Hello, im looking for someone who can help me with overclocking.
Here is my HW configuration:
- GA-P45-DS3R (atm i have F9 bios version coz when i had f10 i think it was worst)
- e7200 2,53GHz (1,25 V max :< )
- AC Freezer 7 Pro
- 4GB (kit 2x2 GB) DDR2 800 MHz PC6400 A-DATA Extreme Edition Vitesta Retail (DDR2-667: 4-4-4-11-2T, 1,9 V; DDR2-850: 5-5-5-18-2T, 2,1 V)
- MSI GeForce N260 GTX
- Corsair WX 550 W
- 2x Samsung SpinPoint F1 640GB, SATA II NCQ, 16MB cache, 7200ot.<Raid 0
- 250 GB Seagate

I was trying make some normal overclocking whole week, i read some threads on this forum, i had 3,4 and 3,6 GHz but unstable, finaly i got 3,2 Ghz stable today but i had some problems with OS and after reinstal i had to setup default options
If somebody can help me, i want 3,6 Ghz or 3,8 Ghz, so If its possible please write me configuration
Thank you very much and sorry for my english:P

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

F10 fixed S3 sleep, if that matters to you. If not then F9 it is!

Please fill this in with your full settings you have now at 3.2 for me, and I will post back some suggested settings for you for 3.6 >>>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................:
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................:


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:
Memory Frequency (Mhz) ..............:
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: <<
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............:
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[laker_faker]

Re: GA-EP45-DS3R (e7200)

Im afraid that it wont be 100% correct informations, coz after reinstal OS it was unstable so now im on defautl setup, but ill try write it

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8 (but this procesor can run on 9,5)
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 400


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 150
MCH Clock Skew (ps)...................: 250


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

Advanced Timing Control
tRRD...........................................4
tWTR..........................................8
tWR............................................8
tRFC...........................................62
tRTP...........................................4
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:6
Twr2wr(Different Rank)...................:6
Twr2rd(Different Rank)...................:6
Trd2wr(Same/Diff Rank)..................:8
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto

Channel B
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:6
Twr2wr(Different Rank)...................:6
Twr2rd(Different Rank)...................:6
Trd2wr(Same/Diff Rank)..................:8
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto

Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

And please, where can i turn off that very long start of bios, detecting hardrives and so on? its dreep to wait all the time 1 minute to windows

And thx for your help

[BongWizard]

Re: GA-EP45-DS3R (e7200)

for 3.6GHz try

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: 0.5
CPU Frequency ...........................: 3.61GHz (380*9.5=3610MHz)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 380MHz
PCI Express Frequency (Mhz) .........: 100MHz <--Always 100!!

C.I.A.2 .................................:[Disabled]


Advanced Clock Control
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0-50
MCH Clock Skew (ps)...................: 50-100


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 333MHz
System Memory Multiplier ..............: 2.00 or 2.40
Memory Frequency (Mhz) ..............: 760MHz or 912MHz (you might be able to get 912, but you'll need to loosen the timings, so try to get stable at 760 first)
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.............................5
tRCD ..............................................5
tRP'.............................................. ...5
tRAS.............................................. .15-18

Advanced Timing Control
tRRD........................................... 3-6
tWTR.......................................... 4-7
tWR............................................ 3-8
tRFC........................................... 52-60
tRTP........................................... 4-7
Command Rate (CMD) ....................: 2

Channel A
Static tRead Value............................: 7-11
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Channel B
Static tRead Value..........................: 7-11
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.350V (as a starting point... if you can't get to Windows, increase it... if you get to Windows then your rig dies, decrease it)
CPU Termination…..... 1.200V*.......: Auto (or you can manually set as 1.28-1.35V)
CPU PLL…………………....1.500V*.......: Auto (should be fine)
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………..0.800V*.......: Auto

MCH/ICH
MCH Core…………….....1.100V...........: 1.2-1.3V
MCH Reference….…….0.800V...........: Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.550V............: Auto
ICH Core…………...……1.100V............: Auto

DRAM
DRAM Voltage ……....1.800V............: 2-2.1V

DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

[laker_faker]

Re: GA-EP45-DS3R (e7200)

Thank you BongWizard i go try it

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

Let us know how you get along

[laker_faker]

Re: GA-EP45-DS3R (e7200)

i tryed it, it didnt works, so i tryed this:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: 0.5
CPU Frequency ...........................: 3.61GHz (380*9.5=3610MHz)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 380MHz
PCI Express Frequency (Mhz) .........: 100MHz

C.I.A.2 .................................:[Disabled]


Advanced Clock Control
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................: 100


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 333MHz
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 760MHz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.............................5
tRCD ..............................................5
tRP'.............................................. ...5
tRAS.............................................. .15

Advanced Timing Control
tRRD........................................... 6
tWTR.......................................... 7
tWR............................................ 8
tRFC........................................... 60
tRTP........................................... 7
Command Rate (CMD) ....................: 2

Channel A
Static tRead Value............................: 11
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Channel B
Static tRead Value..........................: 11
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Motherboard Voltage ControlCPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] < I dont have this

And its unstable, now after 2 mins in OCCT it wrote "critical temperature on CPU" . i dont understand it coz i have AC Freezer Pro 7 and i think its good. And maybe provlem is that i set Ccore up to 1,4V and CPU z shows 1,328

Please help:P

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

1.32 actual is not that much, and you may actually need more. What do you have the "Warning" temp set to? Or what temp is it when it tells you this?

I dont use that too much, so can you please tell me what CoreTemp shows your Idle and Load temps are with Orthos running for 10 minutes or so

See if this helps any >>>

CPU Vcore….……….........................: 1.38-1.39V
CPU Termination…..... 1.200V*.......: 1.32V
CPU PLL…………………....1.500V*.......: 1.50V
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………..0.800V*.......: Auto

MCH/ICH
MCH Core…………….....1.100V...........: 1.24V
MCH Reference….…….0.800V...........: Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.550V............: Auto
ICH Core…………...……1.100V............: Auto

DRAM
DRAM Voltage ……....1.800V............: 2.1V

That cooler may just not be good enough for the voltage you need to run that CPU so high. You may either need to use less paste, or be sure it is on tight.... Or get a better cooler if your temps are hitting 65-70C already

I personally would run 3.6 this way >>>

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
[B]CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: 0.0[/B]
CPU Frequency ...........................: 3.618GHz (402*9=3618MHz)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 402MHz
PCI Express Frequency (Mhz) .........: 100MHz

C.I.A.2 .................................:[Disabled]


Advanced Clock Control
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................: 150-200


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400MHz << Change voltages, Static Tread to highest, and THIS ONLY and reboot and then change the rest

System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 804MHz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.............................5
tRCD ..............................................5
tRP'.............................................. ...5
tRAS.............................................. 15/18

Advanced Timing Control
tRRD........................................... (3-5) 6
tWTR.......................................... 3-6 (may have to set 12 for MCH latch Change)
tWR............................................ 6-8 (May have to set 14 for 400 MCH latch Change)
tRFC........................................... 52-60
tRTP........................................... 3-6
Command Rate (CMD) ....................: 2

Channel A
Static tRead Value............................: 8-11
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Channel B
Static tRead Value..........................: 8-11
tRD Phase0 Adjustment...................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.38-1.39V
CPU Termination…..... 1.200V*.......: 1.32V
CPU PLL…………………....1.500V*.......: 1.50V
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………..0.800V*.......: Auto

MCH/ICH
MCH Core…………….....1.100V...........: 1.24V
MCH Reference….…….0.800V...........: Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.550V............: Auto
ICH Core…………...……1.100V............: Auto

DRAM
DRAM Voltage ……....1.800V............: 2.1V

DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto

[laker_faker]

Re: GA-EP45-DS3R (e7200)

1.32 actual is not that much, and you may actually need more. What do you have the "Warning" temp set to? Or what temp is it when it tells you this?

I dont use that too much, so can you please tell me what CoreTemp shows your Idle and Load temps are with Orthos running for 10 minutes or so

That cooler may just not be good enough for the voltage you need to run that CPU so high. You may either need to use less paste, or be sure it is on tight.... Or get a better cooler if your temps are hitting 65-70C already

[laker_faker]

Re: GA-EP45-DS3R (e7200)

I tryed all posibilities and nothing:(
i cant set it up to 3,6, 3,4 or even 3,2:(

[Dweirdo]

Re: GA-EP45-DS3R (e7200)

laker faker, im with you on this, E7300 with with Ep45-DS3R, only 3.2 got stable, cant get it over it, either we both have bad chips, or we both nabz, or those motherboard with this cpu is not good XD

[Lsdmeasap]

Re: GA-EP45-DS3R (e7200)

Ya, what you set in the BIOS for CPU voltage will be about .6 or so different in windows because of vdrop, and Less then that at full load. So you may need far more then you are trying, but likely not for only 3.4 or so

What is your full settings you are using now that is stable?

[laker_faker]

Re: GA-EP45-DS3R (e7200)

ok so after few other hours of trying, i was stable on 3,5 Ghz, then i tryed ,6 it wasnt stable so i went back to 3,5 and it wasnt stable anymore on same setup, 3,3 wasnt stabel too, i realy dont understand it, i setup it 100% same and one time stable one time not, WTF???
now im on 3,1 and i will cechk in night if its stable
my setings atm:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................:
Fine CPU Clock Ratio.....................:.9
CPU Frequency ...........................: 0.5


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333 Mhz
PCI Express Frequency (Mhz) .........:Auto (i know..)

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0


DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 667
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18

Advanced Timing Control
tRRD...........................................aut o
tWTR..........................................auto
tWR............................................aut o
tRFC...........................................60
tRTP...........................................aut o
Command Rate (CMD) ....................:2auto

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:auto
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:auto
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

[laker_faker]

Re: GA-EP45-DS3R (e7200)

Ok so after 3 mins in OCCT critical CPU temperature, on 3,16 Ghz with AC Freezing Pro 7, 69 C. Great. I can change to emo and jump from window:)
Edit:
I setup max temperature in test to 75 so i will tell you results at the morning.
After 20 min max temperature was 70

[Dweirdo]

Re: GA-EP45-DS3R (e7200)

dude, this temps are huge!!
You are using 1.29v (bios 1.35) this is so weird, is this new pc? u should clean some dirt.