If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Both of you guys can now bring down some of those settings for sure >>>
(G)MCH Frequency Latch...............: 400
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Yeah, you can leave those all set high until you find your CPU overclock you want, then lower them as you test for stability. Leave them high though, until you are sure you CPU is stable, that way when/if you get errors you know it is the CPU and not the ram
Yeah, you can leave those all set high until you find your CPU overclock you want, then lower them as you test for stability. Leave them high though, until you are sure you CPU is stable, that way when/if you get errors you know it is the CPU and not the ram
And please can you tell me what everything i have to increast for stable cpu? which voltages? and for what values +-?
Motherboard Voltage Control
Voltage Type.………... Manual CPU
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: 1.2-1.38 (Higher for higher FSB, I am using 1.34 for 450 FSB, but I am going to bring it down for sure.) 400 or so FSB, I would think 1.2-1.28 would be fine for you. May be even fine at stock value
CPU PLL…………………....1.500V*.......: <<<1.5-1.56
CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)
Those are all the CPU Voltages, only you and your CPU can find what it stable. What CPU speed/FSB are you running and I will give you my best guess at a range to try out
Hello again, as usual i tryed lot of setups, and now i have 100% stable system. Here is my setup
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0.5
CPU Frequency ...........................: 3.41 (402*8.5=3417Mhz)
Clock Chip Control Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 402 Mhz PCI Express Frequency (Mhz) .........:100
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................: 50
DRAM Performance Control Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 804
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Channel A
Static tRead Value.........................: 8
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................: 8
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
I was trying to decreast Voltage but it wasnt stable, so this is my final setup.
I want 3,6 but its unstable wit 1.4625 V in bios (something about 1.38V in CPUID) and im afraid to go higher.
Comment