Re: Wanting to add 16GB and a pinch of OC to EP45T-DS3R...but much bad voodoo, memory, etc.
Here you go...
Here you go...
Code:
Motherboard: Gigabyte GA-EP45T-DS3R Rev#? BIOS: F4c CPU: Intel� Core™2 Quad Processor Q9650 (12M Cache, 3.00 GHz, 1333 MHz FSB) RAM: Crucial DDR3L-1600 PC3L-12800 1900Mhz 9-9-9-24 CL=11 1.35v PSU: Real Power Pro 650W COOLING: Lepa AquaChanger 120 Default settings for new setups that are not overclocked. note: replace all ?? with the value displayed in your bios. ----> Replace "Auto" with manually set values. MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster -------- : [Auto] CPU Clock Ratio ---------------- : [9] Fine CPU Clock Ratio ----------- : [0.0] CPU Frequency ------------------ : 4.05GHz Clock Chip Control Standard Clock Control CPU Host Clock Control --------- : [Enabled] CPU Host Frequency (Mhz) ------- : [450 Mhz] PCI Express Frequency (Mhz) ---- : [100 MHz] C.I.A.2 ------------------------ : [Disabled] Advanced Clock Control ------- CPU Clock Drive ---------------- : 800mv PCI Express Clock Drive -------- : 900mv CPU Clock Skew (ps) ------------ : 0ps MCH Clock Skew (ps) ------------ : 0ps DRAM Performance Control Performance Enhance ------------ : [Standard] Extreme Memory Profile - (XMP) - : [Disabled] I DON’T SEE THIS SETTING IN MY BIOS (G)MCH Frequency Latch --------- : [Auto] System Memory Multiplier ------- : [2.40B] Memory Frequency (Mhz) --------- : [1600 1080] DRAM Timing Selectable --------- : [Auto] Standard Timing Control ------- CAS Latency Time ------- 10 ---- : [11] tRCD ------------------ 11 ---- : [11] tRP -------------------- 11 ---- : [11] tRAS ------------------ 28 ---- : [28] Advanced Timing Control ------- tRRD ------------------ 5 ------ : [Auto] tWTR ------------------ 6 ------ : [Auto] tWR -------------------- 12 ----- : [Auto] tRFC ------------------ 127 ---- : [Auto] tRTP ------------------ 6 ------ : [Auto] Command Rate (CMD) ------- 0 -—-- : [Auto] Channel A Timing Settings -- Static tRead Value ------------- : 10 [9] tRD Phase0 Adjustment ---------- : 0 [Auto] tRD Phase1 Adjustment ---------- : 0 [Auto] tRD Phase2 Adjustment ---------- : 0 [Auto] tRD Phase3 Adjustment ---------- : 0 [Auto] Trd2rd(Different Rank) --------- : 9 [Auto] Twr2wr(Different Rank) --------- : 7 [Auto] Twr2rd(Different Rank) --------- : 7 [Auto] Trd2wr(Same/Diff Rank) --------- : 9 [Auto] Dimm1 Clock Skew Control ------- : [Auto] Dimm2 Clock Skew Control ------- : [Auto] Channel B Timing Settings -- Static tRead Value ------------- : 10 [9] tRD Phase0 Adjustment ---------- : 0 [Auto] tRD Phase1 Adjustment ---------- : 0 [Auto] tRD Phase2 Adjustment ---------- : 0 [Auto] tRD Phase3 Adjustment ---------- : 0 [Auto] Trd2rd(Different Rank) --------- : 9 [Auto] Twr2wr(Different Rank) --------- : 7 [Auto] Twr2rd(Different Rank) --------- : 7 [Auto] Trd2wr(Same/Diff Rank) --------- : 9 [Auto] Dimm1 Clock Skew Control ------- : [Auto] Dimm2 Clock Skew Control ------- : [Auto] Channel A and B Driving Settings ------ Driving Strength Profile ------- : [all are Auto] <-- setting for channel A Driving Strength Profile ------- : [all are Auto] <-- setting for channel B Motherboard Voltage Control CPU Voltage Types--------- Normal ----- Current ----- Load-Line Calibration ---------- : [Enabled] CPU Vcore ----------- 1.28750V - : [1.28750V] CPU Termination ----- 1.200V -- : [1.200V] CPU PLL ------------- 1.500V -- : [1.500V] CPU Reference ------- 0.760V -- : [0.760V] CPU Reference2 ------ N/A ----- : [N/A] I DON’T HAVE THIS SETTING MCH/ICH MCH Core ------------- 1.100V -- : [1.100V] MCH Reference -------- 0.760V -- : [0.760V] MCH/DRAM Ref --------- 0.750V -- : [0.750V] ICH I/O -------------- 1.500V -- : [1.500V] ICH Core ------------- N/A ----- : [N/A] I DON’T HAVE THIS SETTING DRAM DRAM Voltage --------- 1.500V -- : [Auto] DRAM Termination ----- 0.750V -- : [Auto] Ch-A Data VRef. -- 0.750V -- : [Auto] FOR 4 BELOW SETTINGS FOR CH-A/CH-B YOUR LIST ONLY HAD Ch-B Data VRef. -- 0.750V -- : [Auto] A GENERIC “REFERENCE” AND DIDN’T CRACK OUT INTO Ch-A Address VRef. -- 0.750V -- : [Auto] DATA AND ADDRESS VREF Ch-B Address VRef. -- 0.750V -- : [Auto] Advanced Settings Limit CPUID Max. to 3 ---------- : [Disabled] No-Execute Memory Protect ------ : [Enabled] CPU Enhanced Halt (C1E) -------- : [Disabled] C2/C2E State Support ----------- : [Disabled] x C4/C4E State Support --------- : [Disabled] CPU Thermal Monitor 2 (TM2) ---- : [Enabled] CPU EIST Function ------------- : [Disabled] Virtualization Technology ------ : [Enabled] Integrated Peripherals Legacy USB Storage Detect ----- : [Enabled]
Comment