hi,
sometimes it wont boot, HDD led is continuous red, fans not running.
all phase led on. mostly this will happen after a long *off* period, but sometimes allso now and then. but if it runs, it is very stable.
sometimes it wont boot, HDD led is continuous red, fans not running.
all phase led on. mostly this will happen after a long *off* period, but sometimes allso now and then. but if it runs, it is very stable.
Bios F4
Rams: OCZ3G1600LV2G (2x2gb) 8-8-8-24, 1.65v
CPU: i5 750
how can i fix this?
settings as follow:
CPU Clock Ratio 20x
Intel(R) Turbo Boost Tech................[enabled]
CPU Cores Enabled........................[All]
CPU Enhanced Halt (C1E)..................[enabled]
C3/C6/C7 State Support...................[enabled]
CPU Thermal Monitor......................[enabled]
CPU EIST Function........................[enabled]
Bi-Directional PROCHOT...................[enabled]
QPI Clock Ratio..........................[x18]
QPI Link Speed........................[3150mh]
Uncore Clock Ratio....................[16x]
Uncore Frequency.........................2880MHz
Base Clock (BCLK) Control................[Enabled]
BCLK Frequency ..........................[175]
System Memory Multiplier (SPD)...........[8]
Memory Frequency (MHz)................1400
PCI Express Frequency (MHz)..............[100]
C.I.A.2..................................[Disabled]
CPU Clock Drive..........................[ 800mV]
PCI Express Clock Drive..................[ 900mV]
CPU Clock Skew...........................[ 0ps]
System Memory Multiplier (SPD)...........[8]
Memory Frequency (MHz)................1400
Performance Enhance (SPD)............. [std]
DRAM Timing Selectable (SPD)............ [quick]
Profile DDR Voltage ..................1.5v
Profile QPI Voltage ..................1.1v
Channel Interleaving.....................[Auto]
Rank Interleaving........................[Auto]
>>>>> Channel A & B
Channel A Timing Settings [Press Enter]:
Cas Latency Time........................[8]
tRCD....................................[8]
tRP.....................................[8]
tRAS...................................[22]
>>>>> Advanced Timing Control
tRC....................................[Auto]
tRRD...................................[Auto]
tWTR...................................[Auto]
tWR....................................[Auto]
tWTP...................................[Auto]
tWL....................................[Auto]
tRFC...................................[84 Auto]
tRTP...................................[Auto]
tFAW...................................[Auto]
Command Rate (CMD).................. 1 [1]
>>>>> Misc Timing Control
B2B Cas Delay..........................[ Auto]
Round Trip Latency.....................[Auto]
Channel A Turnaround Settings [Press Enter]:
Different DIMMs........................[Auto]
Different DIMMs........................[ Auto]
On The Same Rank.......................[Auto]
Different DIMMs........................[ Auto]
Different DIMMs........................[ Auto]
On The Same Rank.......................[ Auto]
Load Line Calibration...................[auto]
CPU Vcore..................1.1000v..[normal]
CPU DVID.....................[+0.9275v]
QPI/VTT Voltage..........1.100v.....[1.230v]
>>> MCH/ICH
PCH Core....................1.050v.....[1.050]
CPU PLL......................1.800v.....[1.880]
>>> DRAM
DRAM Voltage..............1.500v.....[1.660v]
DRAM Termination.........0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Isochronous Support....................[Enabled]
Virtualisation technology..............[Enabled]
hope i can find some help
cu
Rams: OCZ3G1600LV2G (2x2gb) 8-8-8-24, 1.65v
CPU: i5 750
how can i fix this?
settings as follow:
CPU Clock Ratio 20x
Intel(R) Turbo Boost Tech................[enabled]
CPU Cores Enabled........................[All]
CPU Enhanced Halt (C1E)..................[enabled]
C3/C6/C7 State Support...................[enabled]
CPU Thermal Monitor......................[enabled]
CPU EIST Function........................[enabled]
Bi-Directional PROCHOT...................[enabled]
QPI Clock Ratio..........................[x18]
QPI Link Speed........................[3150mh]
Uncore Clock Ratio....................[16x]
Uncore Frequency.........................2880MHz
Base Clock (BCLK) Control................[Enabled]
BCLK Frequency ..........................[175]
System Memory Multiplier (SPD)...........[8]
Memory Frequency (MHz)................1400
PCI Express Frequency (MHz)..............[100]
C.I.A.2..................................[Disabled]
CPU Clock Drive..........................[ 800mV]
PCI Express Clock Drive..................[ 900mV]
CPU Clock Skew...........................[ 0ps]
System Memory Multiplier (SPD)...........[8]
Memory Frequency (MHz)................1400
Performance Enhance (SPD)............. [std]
DRAM Timing Selectable (SPD)............ [quick]
Profile DDR Voltage ..................1.5v
Profile QPI Voltage ..................1.1v
Channel Interleaving.....................[Auto]
Rank Interleaving........................[Auto]
>>>>> Channel A & B
Channel A Timing Settings [Press Enter]:
Cas Latency Time........................[8]
tRCD....................................[8]
tRP.....................................[8]
tRAS...................................[22]
>>>>> Advanced Timing Control
tRC....................................[Auto]
tRRD...................................[Auto]
tWTR...................................[Auto]
tWR....................................[Auto]
tWTP...................................[Auto]
tWL....................................[Auto]
tRFC...................................[84 Auto]
tRTP...................................[Auto]
tFAW...................................[Auto]
Command Rate (CMD).................. 1 [1]
>>>>> Misc Timing Control
B2B Cas Delay..........................[ Auto]
Round Trip Latency.....................[Auto]
Channel A Turnaround Settings [Press Enter]:
Different DIMMs........................[Auto]
Different DIMMs........................[ Auto]
On The Same Rank.......................[Auto]
Different DIMMs........................[ Auto]
Different DIMMs........................[ Auto]
On The Same Rank.......................[ Auto]
Load Line Calibration...................[auto]
CPU Vcore..................1.1000v..[normal]
CPU DVID.....................[+0.9275v]
QPI/VTT Voltage..........1.100v.....[1.230v]
>>> MCH/ICH
PCH Core....................1.050v.....[1.050]
CPU PLL......................1.800v.....[1.880]
>>> DRAM
DRAM Voltage..............1.500v.....[1.660v]
DRAM Termination.........0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Isochronous Support....................[Enabled]
Virtualisation technology..............[Enabled]
hope i can find some help
cu
Comment