Re: UD3P and Q9550 Overclock Problems
I agree with what Jim says and check the event log it should show a stop error of some sort and a code.
I agree with what Jim says and check the event log it should show a stop error of some sort and a code.
Motherboard: Model: GA-EP45-UD3P(rev 1.6) Bios Version: FDa Cpu: Q9550 E0 Ram: 2X2GB Brand: Mushkin 996559 [url=http://www.mushkin.com/doc/products/memory_detail.asp?id=661]XP2-8500 DDR2 - Mushkin Enhanced[/url] Power Supply Unit: Corsair 620HX MB Intelligent Tweaker (M.I.T.) Robust Graphics Booster ---------------- : [Auto] CPU Clock Ratio ------------------------ : [ 8 X] Fine CPU Clock Ratio ------------------- : [+0.5] CPU Frequency -----------------------: 3.90GHz( 459X8.5) Clock Chip Control Standard Clock Control CPU Host Clock Control ----------------- : [Enabled] CPU Host Frequency (Mhz) --------------- : [ 459] PCI Express Frequency (Mhz) ------------ : [ 100] C.I.A.2 -------------------------------- : [Disabled] Advanced Clock Control [Press Enter] CPU Clock Drive ------------------------ : [ 800mV] PCI Express Clock Drive ---------------- : [ 900Mv] CPU Clock Skew (ps) -------------------- : [ 0ps] MCH Clock Skew (ps) -------------------- : [ 0ps] DRAM Performance Control Performance Enhance -------------------- : [Standard] Extreme Memory Profile --- (X.M.P.) ---- : [Disabled] (G)MCH Frequency Latch ----------------- : [Auto] System Memory Multiplier --------------- : [2.40B] Memory Frequency (Mhz) -----------------: 1066 1102 DRAM Timing Selectable -(SPD)----------- : [Manual] Standard Timing Control CAS Latency Time -------- 5 ------------ : [5] tRCD -------------------- 7 ------------ : [ 5] tRP --------------------- 7 ------------ : [ 5] tRAS ------------------- 24 ------------ : [ 15] Advanced Timing Control [Press Enter] tRRD -------------------- 4 ------------ : [ 3] tWTR -------------------- 4 ------------ : [ 3] tWR --------------------- 8 -------------: [ 5] tRFC --------------------68 ------------ : [52] tRTP -------------------- 4 ------------ : [ 3] Command Rate (CMD) ------ 0 -------------: [Auto] Channel A Channel A Timing Settings [Press Enter] Static tRead Value ------ 8 ------------ : [ 8] tRD Phase0 Adjustment --- 0 ------------ : [Auto] tRD Phase1 Adjustment --- 0 ------------ : [Auto] tRD Phase2 Adjustment --- 0 ------------ : [Auto] tRD Phase3 Adjustment --- 0 ------------ : [Auto] Trd2rd(Different Rank) -- 8 ------------ : [Auto] Twr2wr(Different Rank) -- 8 ------------ : [Auto] Twr2rd(Different Rank) -- 7 ------------ : [Auto] Trd2wr(Same/Diff Rank) -- 9 ------------ : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] Dimm2 Clock Skew Control --------------- : [Auto] DDR Write Training --------------------- : [Auto] Channel B Channel B Timing Settings [Press Enter] Static tRead Value ------ 8 ------------ : [ 8] tRD Phase0 Adjustment --- 0 ------------ : [Auto] tRD Phase1 Adjustment --- 0 ------------ : [Auto] tRD Phase2 Adjustment --- 0 ------------ : [Auto] tRD Phase3 Adjustment --- 0 ------------ : [Auto] Trd2rd(Different Rank) -- 8 ------------ : [Auto] Twr2wr(Different Rank) -- 8 ------------ : [Auto] Twr2rd(Different Rank) -- 7 ------------ : [Auto] Trd2wr(Same/Diff Rank) -- 9 ------------ : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] Dimm2 Clock Skew Control --------------- : [Auto] DDR Write Training --------------------- : [Auto] Channel A Driving Settings [Press Enter] Driving Strength Profile --------------- : [Auto] Data Driving Pull-Up Level ------------- : [Auto] Cmd Driving Pull-Up Level ------------- : [Auto] Ctrl Driving Pull-Up Level ------------- : [Auto] Clk Driving Pull-Up Level ------------- : [Auto] Data Driving Pull-Down Level ----------- : [Auto] Cmd Driving Pull-Down Level ----------- : [Auto] Ctrl Driving Pull-Down Level ----------- : [Auto] Clk Driving Pull-Down Level ----------- : [Auto] Channel B Driving Settings [Press Enter] Driving Strength Profile --------------- : [Auto] Data Driving Pull-Up Level ------------- : [Auto] Cmd Driving Pull-Up Level ------------- : [Auto] Ctrl Driving Pull-Up Level ------------- : [Auto] Clk Driving Pull-Up Level ------------- : [Auto] Data Driving Pull-Down Level ----------- : [Auto] Cmd Driving Pull-Down Level ----------- : [Auto] Ctrl Driving Pull-Down Level ----------- : [Auto] Clk Driving Pull-Down Level ----------- : [Auto] Motherboard Voltage Control CPU Voltage Types ----------- Normal ---------- Current Load-Line Calibration ------------------ : [Disabled] CPU Vcore --------------- 1.28750V ----- : [1.3250V] CPU Termination --------- 1.200V* ------ : [1.220V] CPU PLL ----------------- 1.500V* ------ : [1.500V] CPU Reference ----------- 0.760V* ------ : [0.812V] MCH/ICH MCH Core ---------------- 1.100V ------- : [1.24V] MCH Reference ----------- 0.760V ------- : [0.812V] MCH/DRAM Ref ------------ 0.900V ------- : [1.030V] ICH I/O ----------------- 1.500V ------- : [1.570V] ICH Core ---------------- 1.100V ------- : [1.200V] DRAM DRAM Voltage ------------ 1.800V ------- : [2.060V] DRAM Termination -------- 0.900V ------- : [1.030V] Channel A Reference ----- 0.900V ------- : [Auto] Channel B Reference ----- 0.900V ------- : [Auto] Standard CMOS Features Floppy A ------------------------------- : [None] Floppy 3 Mode Support ------------------ : [Disabled] Advanced Settings Hard Disk Boot Priority ---------------- : [Press Enter] Quick Boot ----------------------------- : [Disabled] First Boot Device ---------------------- : [CDROM] Second Boot Device --------------------- : [Hard Disk] Third Boot Device ---------------------- : [Disabled] Password Check ------------------------- : [Setup] HDD S.M.A.R.T. Capability -------------- : [Enabled] Limit CPUID Max. to 3 ------------------ : [Disabled] No-Execute Memory Protect -------------- : [Enabled] CPU Enhanced Halt (C1E) ---------------- : [Disabled] C2/C2E State Support ------------------- : [Disabled] x C4/C4E State Support ----------------- : [Disabled] CPU Thermal Monitor 2 (TM2) ------------ : [Enabled] CPU EIST Function ---------------------- : [Disabled] Virtualization Technology -------------- : [Disabled] Display For HDD (Secs) ----------------- : [ 0] Full Screen LOGO Show ------------------ : [Disabled] Backup BIOS Image to HDD --------------- : [Disabled] Init Display First --------------------- : [PCI] Integrated Peripherals SATA RAID/AHCI Mode -------------------- : [Disabled] SATA Port0-3 Native Mode --------------- : [Disabled] Azalia Codec --------------------------- : [Disabled] Onboard H/W 1394 ----------------------- : [Disabled] Onboard H/W LAN1 ----------------------- : [Enabled] Onboard H/W LAN2 ----------------------- : [Enabled] Green Lan ------------------------------ : [Disabled] Smart LAN1 ----------------------------- : [Press Enter] Smart LAN2 ----------------------------- : [Press Enter] Onboard LAN1 Boot ROM ------------------ : [Disabled] Onboard LAN2 Boot ROM ------------------ : [Disabled] Onboard SATA/IDE Device ---------------- : [Enabled] Onboard SATA/IDE Ctrl Mode ------------- : [IDE] Onboard Serial Port 1 ------------------ : [Disabled] Onboard Parallel Port ------------------ : [Disabled] X Parallel Port Mode ------------------- : SPP X ECP Mode Use DMA --------------------- : 3 USB 1.0 Controlller -------------------- : [Enabled] USB 2.0 Controlller -------------------- : [Enabled] USB Keyboard Function ------------------ : [Enabled] USB Mouse Function --------------------- : [Enabled] USB Storage Function ------------------- : [Disabled] PC Health Status Reset Case Open Status ----------------- : [Disabled] CPU Warning Temperature ---------------- : [70 C/150 F] CPU Fan Warning ------------------------ : [Disabled] System Fan2 Fail Warning --------------- : [Disabled] Power Fan Warning ---------------------- : [Disabled] CPU Smart Fan Control ------------------ : [Enabled] CPU Samrt Fan Mode --------------------- : [PWM] OCCT 1 Hour - No Errors Ran Prime95 for 2+ hours Vista Reboot __________________
Advanced Timing Control [Press Enter] tRRD -------------------- 4 ------------ : [ 3] 4 tWTR -------------------- 4 ------------ : [ 3] 4 tWR --------------------- 8 -------------: [ 5] 8 tRFC --------------------68 ------------ : [52] 68 tRTP -------------------- 4 ------------ : [ 3] 4 Command Rate (CMD) ------ 0 -------------: [Auto] 2
Q9650 @ 4.10GHz [9x456MHz] P35-DS4 [rev: 2.0] ~ Bios: F14 4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15 MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ----> Seasonic SS-660XP2 80 Plus Platinum psu (660w) WD Caviar Black WD6401AALS 640GB (data) Samsung 840 Pro 256GB SSD (boot) SLI @ 16/4 works when running HyperSLI |
Cooler Master 120XL Seidon push/pull AIO cpu water cooling Cooler Master HAF XB computer case (RC-902XB-KKN1) Asus VH242H 24" monitor [1920x1080] MSI N460GTX Hawk (1GB) video card Logitech Z-5500 Digital 5.1 Speakers win7 x64 sp1 Home Premium HT|Omega Claro plus+ sound card CyberPower CP1500PFCLCD UPS |
Motherboard: Model: GA-EP45-UD3P(rev 1.6) Bios Version: FD Cpu: Q9550 E0 Ram: 2X2GB Brand: Mushkin 996559 [url=http://www.mushkin.com/doc/products/memory_detail.asp?id=661]991599 - 2GB DDR2 PC2-8500 5-5-5-15 Blackline (Module)[/url] Power Supply Unit: Corsair 620HX MB Intelligent Tweaker (M.I.T.) Robust Graphics Booster ---------------- : [Auto] CPU Clock Ratio ------------------------ : [ 8 X] Fine CPU Clock Ratio ------------------- : [+0.5] CPU Frequency -----------------------: 3.82GHz( 450X8.5) Clock Chip Control Standard Clock Control CPU Host Clock Control ----------------- : [Enabled] CPU Host Frequency (Mhz) --------------- : [ 450] PCI Express Frequency (Mhz) ------------ : [ 100] C.I.A.2 -------------------------------- : [Disabled] Advanced Clock Control [Press Enter] CPU Clock Drive ------------------------ : [ 800mV] PCI Express Clock Drive ---------------- : [ 900Mv] CPU Clock Skew (ps) -------------------- : [ 0ps] MCH Clock Skew (ps) -------------------- : [ 0ps] DRAM Performance Control Performance Enhance -------------------- : [Standard] Extreme Memory Profile --- (X.M.P.) ---- : [Disabled] (G)MCH Frequency Latch ----------------- : [Auto] System Memory Multiplier --------------- : [2.40B] Memory Frequency (Mhz) -----------------: 1066 1080 DRAM Timing Selectable -(SPD)----------- : [Manual] Standard Timing Control CAS Latency Time -------- 5 ------------ : [5] tRCD -------------------- 7 ------------ : [ 5] tRP --------------------- 7 ------------ : [ 5] tRAS ------------------- 24 ------------ : [ 15] Advanced Timing Control [Press Enter] tRRD -------------------- 4 ------------ : [ 3] tWTR -------------------- 4 ------------ : [ 3] tWR --------------------- 8 -------------: [ 5] tRFC --------------------68 ------------ : [52] tRTP -------------------- 4 ------------ : [ 3] Command Rate (CMD) ------ 0 -------------: [Auto] Channel A Channel A Timing Settings [Press Enter] Static tRead Value ------ 8 ------------ : [ 8] tRD Phase0 Adjustment --- 0 ------------ : [Auto] tRD Phase1 Adjustment --- 0 ------------ : [Auto] tRD Phase2 Adjustment --- 0 ------------ : [Auto] tRD Phase3 Adjustment --- 0 ------------ : [Auto] Trd2rd(Different Rank) -- 8 ------------ : [Auto] Twr2wr(Different Rank) -- 8 ------------ : [Auto] Twr2rd(Different Rank) -- 7 ------------ : [Auto] Trd2wr(Same/Diff Rank) -- 9 ------------ : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] Dimm2 Clock Skew Control --------------- : [Auto] DDR Write Training --------------------- : [Auto] Channel B Channel B Timing Settings [Press Enter] Static tRead Value ------ 8 ------------ : [ 8] tRD Phase0 Adjustment --- 0 ------------ : [Auto] tRD Phase1 Adjustment --- 0 ------------ : [Auto] tRD Phase2 Adjustment --- 0 ------------ : [Auto] tRD Phase3 Adjustment --- 0 ------------ : [Auto] Trd2rd(Different Rank) -- 8 ------------ : [Auto] Twr2wr(Different Rank) -- 8 ------------ : [Auto] Twr2rd(Different Rank) -- 7 ------------ : [Auto] Trd2wr(Same/Diff Rank) -- 9 ------------ : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] Dimm2 Clock Skew Control --------------- : [Auto] DDR Write Training --------------------- : [Auto] Channel A Driving Settings [Press Enter] Driving Strength Profile --------------- : [Auto] Data Driving Pull-Up Level ------------- : [Auto] Cmd Driving Pull-Up Level ------------- : [Auto] Ctrl Driving Pull-Up Level ------------- : [Auto] Clk Driving Pull-Up Level ------------- : [Auto] Data Driving Pull-Down Level ----------- : [Auto] Cmd Driving Pull-Down Level ----------- : [Auto] Ctrl Driving Pull-Down Level ----------- : [Auto] Clk Driving Pull-Down Level ----------- : [Auto] Channel B Driving Settings [Press Enter] Driving Strength Profile --------------- : [Auto] Data Driving Pull-Up Level ------------- : [Auto] Cmd Driving Pull-Up Level ------------- : [Auto] Ctrl Driving Pull-Up Level ------------- : [Auto] Clk Driving Pull-Up Level ------------- : [Auto] Data Driving Pull-Down Level ----------- : [Auto] Cmd Driving Pull-Down Level ----------- : [Auto] Ctrl Driving Pull-Down Level ----------- : [Auto] Clk Driving Pull-Down Level ----------- : [Auto] Motherboard Voltage Control CPU Voltage Types ----------- Normal ---------- Current Load-Line Calibration ------------------ : [Enabled] CPU Vcore --------------- 1.28750V ----- : [1.3250V] CPU Termination --------- 1.200V* ------ : [1.220V] CPU PLL ----------------- 1.500V* ------ : [1.500V] CPU Reference ----------- 0.760V* ------ : [0.812V] MCH/ICH MCH Core ---------------- 1.100V ------- : [1.26V] MCH Reference ----------- 0.760V ------- : [0.812V] MCH/DRAM Ref ------------ 0.900V ------- : [1.030V] ICH I/O ----------------- 1.500V ------- : [1.570V] ICH Core ---------------- 1.100V ------- : [1.200V] DRAM DRAM Voltage ------------ 1.800V ------- : [2.060V] DRAM Termination -------- 0.900V ------- : [1.030V] Channel A Reference ----- 0.900V ------- : [Auto] Channel B Reference ----- 0.900V ------- : [Auto] Standard CMOS Features Floppy A ------------------------------- : [None] Floppy 3 Mode Support ------------------ : [Disabled] Advanced Settings Hard Disk Boot Priority ---------------- : [Press Enter] Quick Boot ----------------------------- : [Disabled] First Boot Device ---------------------- : [CDROM] Second Boot Device --------------------- : [Hard Disk] Third Boot Device ---------------------- : [Disabled] Boot Up Floppy Seek -------------------- : [Disabled] Boot up Num-Lock ----------------------- : [On] Password Check ------------------------- : [Setup] HDD S.M.A.R.T. Capability -------------- : [Enabled] Limit CPUID Max. to 3 ------------------ : [Disabled] No-Execute Memory Protect -------------- : [Disabled] CPU Enhanced Halt (C1E) ---------------- : [Disabled] C2/C2E State Support ------------------- : [Disabled] x C4/C4E State Support ----------------- : [Disabled] CPU Thermal Monitor 2 (TM2) ------------ : [Enabled] CPU EIST Function ---------------------- : [Disabled] Virtualization Technology -------------- : [Disabled] Display For HDD (Secs) ----------------- : [ 0] Full Screen LOGO Show ------------------ : [Disabled] Backup BIOS Image to HDD --------------- : [Disabled] Init Display First --------------------- : [PCI] Integrated Peripherals SATA RAID/AHCI Mode -------------------- : [Disabled] SATA Port0-3 Native Mode --------------- : [Disabled] Azalia Codec --------------------------- : [Auto] Onboard H/W 1394 ----------------------- : [Disabled] Onboard H/W LAN1 ----------------------- : [Enabled] Onboard H/W LAN2 ----------------------- : [Enabled] Green Lan ------------------------------ : [Disabled] Smart LAN1 ----------------------------- : [Press Enter] Smart LAN2 ----------------------------- : [Press Enter] Onboard LAN1 Boot ROM ------------------ : [Disabled] Onboard LAN2 Boot ROM ------------------ : [Disabled] Onboard SATA/IDE Device ---------------- : [Enabled] Onboard SATA/IDE Ctrl Mode ------------- : [IDE] Onboard Serial Port 1 ------------------ : [Disabled] Onboard Parallel Port ------------------ : [Disabled] X Parallel Port Mode ------------------- : SPP X ECP Mode Use DMA --------------------- : 3 USB 1.0 Controlller -------------------- : [Enabled] USB 2.0 Controlller -------------------- : [Enabled] USB Keyboard Function ------------------ : [Enabled] USB Mouse Function --------------------- : [Enabled] USB Storage Function ------------------- : [Disabled] PC Health Status Reset Case Open Status ----------------- : [Disabled] CPU Warning Temperature ---------------- : [70 C/150 F] CPU Fan Warning ------------------------ : [Disabled] System Fan2 Fail Warning --------------- : [Disabled] Power Fan Warning ---------------------- : [Disabled] System Fan1 Fail Warning --------------- : [Disabled] CPU Smart Fan Control ------------------ : [Enabled] CPU Samrt Fan Mode --------------------- : [PWM] Ran Prime95 for 13+ hours
Q9650 @ 4.10GHz [9x456MHz] P35-DS4 [rev: 2.0] ~ Bios: F14 4x2GB OCZ Reaper PC2-8500 1094MHz @5-5-5-15 MSI N460GTX Hawk Talon Attack (1GB) video card <---- SLI ----> Seasonic SS-660XP2 80 Plus Platinum psu (660w) WD Caviar Black WD6401AALS 640GB (data) Samsung 840 Pro 256GB SSD (boot) SLI @ 16/4 works when running HyperSLI |
Cooler Master 120XL Seidon push/pull AIO cpu water cooling Cooler Master HAF XB computer case (RC-902XB-KKN1) Asus VH242H 24" monitor [1920x1080] MSI N460GTX Hawk (1GB) video card Logitech Z-5500 Digital 5.1 Speakers win7 x64 sp1 Home Premium HT|Omega Claro plus+ sound card CyberPower CP1500PFCLCD UPS |
Comment