Creative X-Fi no sound with Gigabyte UD-5 X-58 board

[Lsdmeasap]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Ahh, I have done that a time or two myself!

Good luck, and if you get quick failures you might need to just raise vcore a bit ot QPI/Vtt

[TorwaK]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Ahh, I have done that a time or two myself!

Good luck, and if you get quick failures you might need to just raise vcore a bit ot QPI/Vtt

Mate as you can see I reached 4Ghz limit however I can't enable HT at bios because of I get BSOD when I run 3DMark06 or somthing which is forcing the CPU. I tried to increase my VTT and VCPU however it didnt help me. Do you have any idea?

[Lsdmeasap]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Hmm, I'd need to see all your settings to even start to advise you of things to try.

Lets see what you are using and I will suggest some things to try out

[B]Advanced CPU Features:[/B]
CPU Clock Ratio ................................ [20x]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Enabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Enabled]
Virtualization Technology ................... [Enabled]
Bi-Directional PROCHOT ..................... [Enabled]


[B]Uncore & QPI Features:[/B]
QPI Link Speed .............................. 
Uncore Frequency .......................... 
Isonchronous Frequency ..................[Enabled]


[B]Standard Clock Control:[/B]
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

[B]Advanced Clock Control:[/B]
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


[B]Advanced DRAM Features:[/B]
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO]
DRAM Timing Selectable (SPD) .......... [Manual]

[B]Channel A

Channel A Timing Settings:[/B]
##Channel A Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................

##Channel A Advanced Timing Control##
tRC .........................................
tRRD .......................................
tWTR ......................................
tWR ........................................
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel A Misc Timing Control##
Round Trip Latency ...................


[B]Channel B

Channel B Timing Settings:[/B]
##Channel B Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................

##Channel B Advanced Timing Control##
tRC .........................................
tRRD .......................................
tWTR ......................................
tWR ........................................
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel B Misc Timing Control##
Round Trip Latency ...................


[B]Channel C

Channel C Timing Settings:[/B]
##Channel C Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................

##Channel C Advanced Timing Control##
tRC .........................................
tRRD .......................................
tWTR ......................................
tWR ........................................
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel C Misc Timing Control##
Round Trip Latency ...................


[B]Advanced Voltage Control:

CPU[/B]
Load Line Calibration ................. [Disabled]
CPU Vcore ...............................
QPI/VTT Voltage 1.150v ............
CPU PLL 1.800v .......................

[B]MCH/ICH[/B]
PCIE 1.500v ...........................
QPI PLL 1.100v .......................
IOH Core 1.100v .....................
ICH I/O 1.500v .......................
ICH Core 1.1v ........................

[B]DRAM[/B]
DRAM Voltage 1.500v ..............
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

[TorwaK]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Roger... When I go home I'll share my BIOS screen shots.

[TorwaK]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Those are shots from my BIOS settings.. I'd to listen your advices to make my HT option enable with overclock.

[C3D76]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Hi Torwak.

From your "advanced clock control" screenshot it looks like you did not load optimized defaults before OC'ing.

If you load Optimized defaults, values change to:
"Cpu Clock drive = 800", and "PCI Express clockdrive = 900" (I think)

[TorwaK]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Hi,

I increased the values Cpu Clock drive = 800, and PCI Express clockdrive = 900 however it didn't help me out about enable my HT option. It seems like not enough voltage for it.

Btw at least I break 25k wall. However my CPU score is low because of I can't enable HT option.

[Lsdmeasap]

Re: Creative X-Fi no sound with Gigabyte UD-5 X-58 board

Manually changing those setting does not help as it would not apply all other hidden settings that optimized defaults load.

So please try again, but load optimized defaults and start over with entering all your settings after you reboot. You will HAVE TO set your SATA/Disk settings again before you load windows, do not forget

That is a lot of Vcore for only 4Ghz. I see most get that at 1.25-1.3 with HT enabled. I use 1.34 and I think my CPU is volt hungry, so I think you may need some other voltage set and then you would not think you need so much Vcore.

But now that I look again, I do see you are running 20x200, I have only ran 21x190 (Needs 1.34) and 21x200 needs 1.36-1.376 those are CPU-z voltages. Same as I mention above, most 920 only need 1.25-1.3 or so for 4Ghz from what I see.

What Try Performance Enhance standard, less QPI PLL, Less IPH Voltage as well, and CPU PLL 1.84-1.88