How do you guys copy and post your MIT settings?
Announcement
Collapse
No announcement yet.
copy and post bios??
Collapse
X
-
Re: copy and post bios??
No, lsd provides a template, and i saw a post where he explained how to do it. It's just a simple keyboard combo to copy that mit page and to post it here.
I've spent 2 freakin' hours looking for that post, but can't find it....grrrr
Comment
-
Re: copy and post bios??
I've found a post - But IGNORE the settings shown in it and enter your own in place!
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [8]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [333]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.40] = 800
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 5
Dram RAS# Precharge Delay_______5
Precharge Delay (tRAS)__________ 18
ACT to ACT Delay (tRRD)_________ 3-5
Rank Write to READ Delay________ 3-6
Write to Precharge Delay_________ 4-8
Refresh to ACT Delay______________ 52-65
Read to Precharge Delay__________ 3-5
Static tRead Value_______________8-12
Static tRead Phase Adjust________ [Auto] << Always leave
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.2V - +0.3] =2.0V -2.1V
PCI-E OverVoltage Control_ [+0.1V] << For stability
FSB OverVoltage Control___ [+0.1V] << For stability
(G)MCH OverVoltage Control [+0.0V - +0.2] << Needed for 2x2 ram
CPU Voltage Control_______ [1.20]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USBLast edited by VorLonUK; 10-29-2008, 05:50 PM.GA-P35C-DS3R Rev2.0 F11 bios, E8200 (@3.0Ghz), OCZ DDR3 PC3-10666 Reaper 4GB (@1200Mhz), Xonar D1, 8800GTS 512, Corsair HX520 (Single 12volt line, Max 40A), WDC 3200aaks/5000aaks in AHCI mode, Vista 64 Premium.
Comment
-
Re: copy and post bios??
Yes, it is all done by hand and pencil. Then copy/paste in the forum and enter your settings.
If you have a 10 year old Printer the Print screen button will print right to the printer. However this may also save the Screenshot into the print buffer so you can print it into Wordpad, Paint or Any image Program via Edit, paste. I will go test this now, as I have not tried it in years. But still that would be a image, so same as taking a picture with your camera.
Asus used to include a File Called CMOS.EXE which would print the settings all to a txt file, but they have not included that for many years (And yes I looked, could not find you one)
*EDIT*
No luck with my Print screen button, but I do not have a printer installed so the buffer may not be able to run to hold things?? Anyhow, just make it easier on yourself and copy one of these into a notepad or wordpad and then print them off. Then you can just go into your BIOS and write down the settings you are using and come post them. Be much easier that way as you would not have to write it all out, only your settings used. >>>
P31/35 Boards >>>
Code:Robust Graphics Booster___________ [Auto] CPU Clock Ratio ____________ [8] Fine Clock Ratio ____________[0.5] CPU Host Clock Control_ [Enabled] CPU Host Frequency (MHz)__________ [450] PCI Express Frequency (Mhz)_______ [100] C.I.A. 2__________________________ [Disabled] System Memory Multiplier (SPD)____ [2.00] DRAM Timing Selectable_______ SPD __ [Manual] Performance Enhance = [Standard] CAS Latency Time________________ ? Dram RAS# to CAS# Delay_________ ? Dram RAS# Precharge Delay_______? Precharge Delay (tRAS)__________ ? ACT to ACT Delay (tRRD)_________ ? Rank Write to READ Delay________ ? Write to Precharge Delay_________ ? Refresh to ACT Delay______________ ? Read to Precharge Delay__________ ? Static tRead Value_______________ Static tRead Phase Adjust________ [Auto] System Voltage Control____ [Manual] DDR2 OverVoltage Control__ [+0.300V] PCI-E OverVoltage Control_ [+0.1V] FSB OverVoltage Control___ [+0.1V] (G)MCH OverVoltage Control [+0.1V] CPU Voltage Control_______ [1.25] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC Integrated Peripherals Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB
Code:[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] Robust Graphics Booster ...............: CPU Clock Ratio ..........................: Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: [b][u]Clock Chip Control [/u][/b] [b][u]Standard Clock Control[/u][/b] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: Mhz [B]PCI Express Frequency (Mhz) .........:Set to 100[/B] C.I.A.2 .................................:[Disabled] [b][u]Advanced Clock Control [Press Enter][/u][/b] CPU Clock Drive...........................: <<< PCI Express Clock Drive.................: <<< CPU Clock Skew (ps)....................: <<< MCH Clock Skew (ps)...................: <<< [b][u]DRAM Performance Control[/u][/b][u][/u] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [Auto] System Memory Multiplier ..............: Memory Frequency (Mhz) ..............: DRAM Timing Selectable ................: [Manual] [b]Standard Timing Control[/b] CAS Latency Time........................ tRCD ......................................... tRP'........................................... tRAS.......................................... [b][u]Advanced Timing Control[/u][/b] tRRD........................................... tWTR.......................................... tWR............................................ tRFC........................................... tRTP........................................... Command Rate (CMD) ....................:2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................ [b]Channel A[/b] Static tRead Value.........................:7-10 tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b]Channel B[/b] Static tRead Value.........................:7-10 tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b][U]Motherboard Voltage Control[/U][/b][U][/U] Voltage Type.���... Manual [b]CPU[/b] CPU Vcore�.���.........................: CPU Termination�..... 1.200V*.......: <<< Leave CPU PLL�������....1.500V*.......: <<< Leave CPU Referen.����....0.755V*.......: <<< .64% Of Vtt (Termination above) CPU Reference2���,,0.800V*.......:<<< .67% Of Vtt (Termination above) [b]MCH/ICH[/b] MCH Core�����.....1.100V...........: << MCH Reference�.��.0.800V...........; <<< Leave MCH/DRAM Ref.�......0.900V...........: <<< Leave ICH I/O������.....1.550V............: <<< Leave ICH Core����...��1.100V............: <<< Leave DRAM DRAM Voltage ��....1.800V............: DRAM Termination .�0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [b][U]Advanced Settings[/U][/b][U][/U] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [b][U]Integrated Peripherals[/U][/b][U][/U] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Last edited by Lsdmeasap; 10-30-2008, 01:15 AM.
Comment
-
Re: copy and post bios??
THANK YOU LSD....such a simple answer to a simple question. I guess nobody knew what i was asking! Here you are...
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [9]
Fine Clock Ratio ____________[0.0] (greyed out)
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [412]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00]
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 4
Dram RAS# to CAS# Delay_________ 4
Dram RAS# Precharge Delay_______4
Precharge Delay (tRAS)__________ 13
ACT to ACT Delay (tRRD)_________ auto
Rank Write to READ Delay________ auto
Write to Precharge Delay_________ auto
Refresh to ACT Delay______________ auto
Read to Precharge Delay__________ auto
Static tRead Value_______________auto
Static tRead Phase Adjust________ [Auto]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.200V]
PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control normal
CPU Voltage Control_______1.325
default voltage (greyed out) 1.225v
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: disabled
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from Usb
----------
bios f5
Monitor is still very slow at 1st boot-up of the day...fine after that.Last edited by jazluvr; 10-30-2008, 11:40 AM.
Comment
-
Re: copy and post bios??
Monitor issue could be your PSU or GFX card, or your actual monitor.
Which Mushkin Model is this? These right 996523? Just wondered because of the Main timings you were using, Wasn't sure if you still had those sticks or not.
Here is optimal ranges for your setup above >>>
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [9]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [412]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00]
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 4
Dram RAS# to CAS# Delay_________ 4
Dram RAS# Precharge Delay_______3/4
Precharge Delay (tRAS)__________10/12/13
Set to all higest below and then later lower once at a time testing as you go with memtest86+
ACT to ACT Delay (tRRD)_________3-4
Rank Write to READ Delay________ 3-6
Write to Precharge Delay_________ 4-6
Refresh to ACT Delay______________ 38-42
Read to Precharge Delay__________ 2-5
Static tRead Value_______________6 (7-10)
Static tRead Phase Adjust________ [Auto] << always leave
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.200V] -0.3
PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.1V] For stability
CPU Voltage Control_______1.325
default voltage (greyed out) 1.225v
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: Enabled
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from Usb
Comment
-
Re: copy and post bios??
These settings are pretty much the same as i have now. They are to get an oc of 3.7, which i have and am 10 runs of intelburntest and 1/2 hour orthos stable. 2 passes of memtest just to see if test 5 would catch anything glaring. I only ran orthos shortly to test other chipsets and subsystem. I thought you said i could get to 4ghz, and were going to post settings for that.
I'm sorry about the misunderstanding and for wasting your time, but we did talk about that. You probably forgot because you are so busy here. We talked about it in my monitor thread. I think i know what the problem with the monitor is.
The slot is only pci-e1.1 which only provides 75watts, the problem, and 2.5gb of bandwidth, (my card can't saturate this bus) :-), and 2.0 provides 150w from the slot, which my 2.0 card needs, and has a bandwidth of 5gb's . I already bumped the bus up by 0.1v, but this morning, it booted right up...wierd.
When i was testing my card with evga precision and ati tool, i had task manager up so i could see what the load my cpu was powering the card, and it was only 1/2 load or less. So there is no cpu bottleneck at load for the card. 3.7ghz is plenty to power my card.
So from reading different posts in different forums, i should be glad it works at all. I'll try bumping up the pci-e v a little more. But I can't even boot into windows with anything tighter than [email protected]. That's @ 3.6. To get to 3.7, i just had to raise it to 4-4-4-13 and raise voltage to what you gave me here. And oh yeah, the ram is same...mushkin #996523
The only difference is the setting with question marks are filled in, but like i said, i am very stable with the setting i am @ now. And i think all the testing i did with burnin helped the mx-2 to settle in, because my temps seem to be improving.
If you think you can give me settings to get to 4ghz, and have time to post them, that would be great, but seeing as how i am stable at 3.7, i'm not going to mess with anything. If it ain't broke, don't fix it, right? Thank's again for your time and help.Last edited by jazluvr; 10-31-2008, 11:55 AM.
Comment
-
Re: copy and post bios??
K, sorry! Yeah I do answer so many posts!
Here is for 4Ghz, I just thought you would be there by now! All you need to do is maybe loosen ram a bit until you get CPU Stable by upping FSB and voltages >>>>
Robust Graphics Booster___________ [Auto] or Fast
CPU Clock Ratio ____________ [9]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [450]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00]
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 4/5
Dram RAS# to CAS# Delay_________ 4/5
Dram RAS# Precharge Delay_______4/5
Precharge Delay (tRAS)__________12/15
Set to all higest below and then later lower once at a time testing as you go with memtest86+
ACT to ACT Delay (tRRD)_________3-4
Rank Write to READ Delay________ 3-6
Write to Precharge Delay_________ 4-6
Refresh to ACT Delay______________ 38-42
Read to Precharge Delay__________ 2-5
Static tRead Value_______________7-10
Static tRead Phase Adjust________ [Auto] << always leave
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.200V] -0.3
PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.1V] For stability
CPU Voltage Control_______1.325 << Will need more, Around 1.3-1.34 or so Actual, not what you set in the BIOS
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: Enabled
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from Usb
Comment
-
Re: copy and post bios??
Awesome! Thanks Lsd! You da man....I'll go try it now. I'll let you know how it goes. Just hope the xiggy does it's job and cools this thing down well. 2nd day in a row my monitor has started right up. Thing has a mind of it's own!
Comment
Comment