I don't know...
This will be about my third thread started on this subject. Maybe I wasn't asking the right questions.
Before I start up again let me say a greatful thanks to those who tried to help before.
Been reading everything I can but can't seem to get a grip on the subject of figuring out how my system sets up FSB/DRAM ratios to it's respective strap. I'm just stumped.
Below are the different Memory Multiplier values available for my board. All I did was start on AUTO, pressed the Page Down key to the next value, took a pic, pressed the Page Down key again, took another pic, and so on, and so on.....till I wound back up on AUTO.
Now, I know that 4.0+ means that the memory will run 4x FSB on the 800 strap at a certain speed of the FSB. Same scenario with 4.0~ except it will be on the 1066 strap.
I already know that I CANNOT run my memory and overclock the FSB enough to utilize the respective strap/1:2 ratio: it would be clocked at gazillion Mhz and I wouldn't be able to bootup at all.
The question that I tried to put forth in my previous threads is: what straps are the other Memory Multiplier values(2.0, 2.4, 2.5, 3.0, 3.20, and 3.33) running on???
I am almost postive that 2.0(1:1) is on the 1066 strap. I have clocked my FSB up to 540 Mhz(Real), with memory at 1080 (540 Mhz) and tested it with MemTest STANDARD 6 full passes with no errors. I couldn't imagine it passing if it was running on the 800 strap.
I know that the Memory Multiplier values have their respective FSB/DRAM ratios. I don't know all of them off-hand (4.0x of course is 1:2 and 2.0x is 1:1, I think 2.4x is 5:6).
So, again my question is: what strap are the other values running on: 800 or 1066? To the best of my knowledge those are the only 2 straps that I can use when overclocking (FSB and/or memory???)
This will be about my third thread started on this subject. Maybe I wasn't asking the right questions.
Before I start up again let me say a greatful thanks to those who tried to help before.
Been reading everything I can but can't seem to get a grip on the subject of figuring out how my system sets up FSB/DRAM ratios to it's respective strap. I'm just stumped.
Below are the different Memory Multiplier values available for my board. All I did was start on AUTO, pressed the Page Down key to the next value, took a pic, pressed the Page Down key again, took another pic, and so on, and so on.....till I wound back up on AUTO.
Now, I know that 4.0+ means that the memory will run 4x FSB on the 800 strap at a certain speed of the FSB. Same scenario with 4.0~ except it will be on the 1066 strap.
I already know that I CANNOT run my memory and overclock the FSB enough to utilize the respective strap/1:2 ratio: it would be clocked at gazillion Mhz and I wouldn't be able to bootup at all.
The question that I tried to put forth in my previous threads is: what straps are the other Memory Multiplier values(2.0, 2.4, 2.5, 3.0, 3.20, and 3.33) running on???
I am almost postive that 2.0(1:1) is on the 1066 strap. I have clocked my FSB up to 540 Mhz(Real), with memory at 1080 (540 Mhz) and tested it with MemTest STANDARD 6 full passes with no errors. I couldn't imagine it passing if it was running on the 800 strap.
I know that the Memory Multiplier values have their respective FSB/DRAM ratios. I don't know all of them off-hand (4.0x of course is 1:2 and 2.0x is 1:1, I think 2.4x is 5:6).
So, again my question is: what strap are the other values running on: 800 or 1066? To the best of my knowledge those are the only 2 straps that I can use when overclocking (FSB and/or memory???)
Comment