Hello my Motherboard is X58A-UD7 Rev 2. I have two problems, starting with OCZ SSD Revodrive x2 PCIe and two new Toshiba hard disk DT01ACA300 3TB.
Before I change my BIOS configuration FD13 (RAID XHD) Running is perfectly follows:
Start by OCZ PCIE-X8_2 Revodrive x2
Intel controller ICHR10R:
Port 0 and 1: Two HDD WD 1TB Black (2TB Raid 0)
Port 2 and 3: Two HDD WD 1TB Black (2TB Raid 0)
Port 4 and 5: Two hard drive WD Black 500GB (1TB Raid 0)
Marvell controller
Port A and B: Two Seagate 2TB (4TB Raid 0)
Gigabyte controller
Puerto D: Asus DVD Player
Puerto E: Empty
The FD13 perfectly bios recognizes the SSDs in RAID XHD Revodrive x2 way to recognize my raids on Intel controller.
Now I introduce my new hardware. Change in ports 4 and 5 of the Intel controller my two 500GB hard disk by Toshiba 2UD DT01ACA300 3TB in IDE mode:
Intel controller ICHR10R:
Port 0 and 1: Two HDD WD 1TB Black (2TB Raid 0)
Port 2 and 3: Two HDD WD 1TB Black (2TB Raid 0)
Puerto 4 and 5: Two hard drive Toshiba 3TB DT01ACA300 (non-RAID)
Marvell controller
Port A and B: Two Seagate 2TB (4TB Raid 0)
Gigabyte controller
Puerto D: DVD Player
Puerto E: Empty
The problems begin.
The FD13 bios only recognizes 750GB but windows 7 x64 if that recognizes 3TB.
After passing the new data and information to 3TB hard disk, formatting and installed new windows 7. When I start windows 7 install all the drivers and see that I can not access certain information from the data stored on disk 3TB. Change 3TB hard drive to Gigabyte and I can access all data 3TB.
As Controller Intel ICHR10R have problems with 3TB update the bios to FD (09/11/2012 3TB + HDD support)
With the new bios FD perfectly accept 3TB drives from Intel controller. But my problem is that I can not start with PCIE Revodrive. RAID mode XHD not recognizing my PCIE RevoDrive x2. I changed X8_2 to PCIE-PCIE-16_2 and still not working. I have also put the graphics card on PCIE-16_2 and RevoDrive PCIe-X16_1 and nowhere PCIE slot, recognizes OCZ Revodrive x2.
If I change the boot AHCI or IDE mode if you recognize my OCZ Revodrive x2. Then this no longer Availablee my Raid 0 of the ports 0-1 and 2-3.
Abandonment bios FD and return to FD13 again. Decide not to connect the 3TB hard drive for problems Intel has given me the windows with no access data.
Start by OCZ PCIE-X8_2 Revodrive x2
Intel controller ICHR10R:
Port 0 and 1: Two HDD WD 1TB Black (2TB Raid 0)
Port 2 and 3: Two HDD WD 1TB Black (2TB Raid 0)
Port 4 and 5: Empty
Marvell controller
Port A and B: Two Seagate 2TB (4TB Raid 0)
Gigabyte controller
Port D-E: Two hard drive Toshiba 3TB DT01ACA300
It seems that it can work well but I need to connect the DVD player. I decide to connect the DVD player in the port 4 and 5 are empty. Then no recognizes my Revodrive x2 PCIE.
I can leave this set up and connect the DVD player to Intel but it seems very strange that connect the DVD fail to recognize Revodrive x2 PCIE. I have also doubts that the Gigabyte controller manages well DT01ACA300 my hard drives Toshiba 3TB.
I can connect my DVD player with a cable SATA to E-SATA controller JMB362 JMICRON (it's the only solution I've found so far)
In the bios is the SATA PORT 0-3 Native Mode option for the Intel controller that is just the solution for my DVD player. Not if activating the option and change the port Raid 0 0-1 4-5 and 0-1 to connect the reader to recognize the problems port X2 Revodrive be solved....
Bios FD13 no problem recognizing RAID X2 Revodrive XHD but does not recognize 3TB disks.
Regards
Before I change my BIOS configuration FD13 (RAID XHD) Running is perfectly follows:
Start by OCZ PCIE-X8_2 Revodrive x2
Intel controller ICHR10R:
Port 0 and 1: Two HDD WD 1TB Black (2TB Raid 0)
Port 2 and 3: Two HDD WD 1TB Black (2TB Raid 0)
Port 4 and 5: Two hard drive WD Black 500GB (1TB Raid 0)
Marvell controller
Port A and B: Two Seagate 2TB (4TB Raid 0)
Gigabyte controller
Puerto D: Asus DVD Player
Puerto E: Empty
The FD13 perfectly bios recognizes the SSDs in RAID XHD Revodrive x2 way to recognize my raids on Intel controller.
Now I introduce my new hardware. Change in ports 4 and 5 of the Intel controller my two 500GB hard disk by Toshiba 2UD DT01ACA300 3TB in IDE mode:
Intel controller ICHR10R:
Port 0 and 1: Two HDD WD 1TB Black (2TB Raid 0)
Port 2 and 3: Two HDD WD 1TB Black (2TB Raid 0)
Puerto 4 and 5: Two hard drive Toshiba 3TB DT01ACA300 (non-RAID)
Marvell controller
Port A and B: Two Seagate 2TB (4TB Raid 0)
Gigabyte controller
Puerto D: DVD Player
Puerto E: Empty
The problems begin.
The FD13 bios only recognizes 750GB but windows 7 x64 if that recognizes 3TB.
After passing the new data and information to 3TB hard disk, formatting and installed new windows 7. When I start windows 7 install all the drivers and see that I can not access certain information from the data stored on disk 3TB. Change 3TB hard drive to Gigabyte and I can access all data 3TB.
As Controller Intel ICHR10R have problems with 3TB update the bios to FD (09/11/2012 3TB + HDD support)
With the new bios FD perfectly accept 3TB drives from Intel controller. But my problem is that I can not start with PCIE Revodrive. RAID mode XHD not recognizing my PCIE RevoDrive x2. I changed X8_2 to PCIE-PCIE-16_2 and still not working. I have also put the graphics card on PCIE-16_2 and RevoDrive PCIe-X16_1 and nowhere PCIE slot, recognizes OCZ Revodrive x2.
If I change the boot AHCI or IDE mode if you recognize my OCZ Revodrive x2. Then this no longer Availablee my Raid 0 of the ports 0-1 and 2-3.
Abandonment bios FD and return to FD13 again. Decide not to connect the 3TB hard drive for problems Intel has given me the windows with no access data.
Start by OCZ PCIE-X8_2 Revodrive x2
Intel controller ICHR10R:
Port 0 and 1: Two HDD WD 1TB Black (2TB Raid 0)
Port 2 and 3: Two HDD WD 1TB Black (2TB Raid 0)
Port 4 and 5: Empty
Marvell controller
Port A and B: Two Seagate 2TB (4TB Raid 0)
Gigabyte controller
Port D-E: Two hard drive Toshiba 3TB DT01ACA300
It seems that it can work well but I need to connect the DVD player. I decide to connect the DVD player in the port 4 and 5 are empty. Then no recognizes my Revodrive x2 PCIE.
I can leave this set up and connect the DVD player to Intel but it seems very strange that connect the DVD fail to recognize Revodrive x2 PCIE. I have also doubts that the Gigabyte controller manages well DT01ACA300 my hard drives Toshiba 3TB.
I can connect my DVD player with a cable SATA to E-SATA controller JMB362 JMICRON (it's the only solution I've found so far)
In the bios is the SATA PORT 0-3 Native Mode option for the Intel controller that is just the solution for my DVD player. Not if activating the option and change the port Raid 0 0-1 4-5 and 0-1 to connect the reader to recognize the problems port X2 Revodrive be solved....
Bios FD13 no problem recognizing RAID X2 Revodrive XHD but does not recognize 3TB disks.
Regards
Comment