GA-X58A-UD5 memory issues :(

[REG1STRAT1ON]

Re: GA-X58A-UD5 memory issues :(

Gaming only gets to approx 60-70 - graphics card does most the work here. However after running Prime95 for about 30 seconds i reached 80 degrees. Something is very wrong here - will look at after market coolers.
Currently running the stock intel cooler. CPU i dont believe is throttle down, thats the C1/C3/C5 or something along those lines right? Will give you some BSOD errors, the codes very quite differently each time. Never had BSOD until this new ram.

Will post in the morning - thanks for the help so far - need to sleep (2.00am)

Keep watching this thread -
you guys are great <3

[wazza300]

Re: GA-X58A-UD5 memory issues :(

i think its about right for stock intel cooler,good aftermarket ones are the prolimatech megahalems

to enable cpu throttling you need to use auto cpu voltage if its fixed it wont throttle,or set to normal and add extra voltage in dvid to remain stable

enable eist c3/c6 c1e can be left disabled if your running win7

[REG1STRAT1ON]

Re: GA-X58A-UD5 memory issues :(

Advanced CPU Features:
CPU Clock Ratio ................................ [20x]
Intel(R) Turbo Boost Tech .................. [Disabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Enabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Enabled]
Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... [AUTO] (3200Mhz)
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................[Disabled] (133Mhz)
PCI Express Frequency (MHz) ........... [AUTO]

C.I.A.2 [Disabled] - Can't find this one :(

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [12.0]
DRAM Timing Selectable (SPD) .......... [Expert]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................8
tRCD .......................................8
tRP .........................................8
tRAS .......................................24

Below values may be left in Auto if you like, generally this is fine.  For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

##Channel A Advanced Timing Control##
tRC ........................................[AUTO]  (Should be = tRAS + tRP or above for stability)
tRRD .......................................[AUTO] 
tWTR ...................................... [AUTO] (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................[AUTO] 
tWTP .......................................[AUTO]    (tWTP Must = tWR + tWL + 4)
tWL ........................................[AUTO]     (tWL Must be CAS Latency -1)
tRFC .......................................[AUTO] 
tRTP .......................................[AUTO] 
tFAW ......................................[AUTO] 
Command Rate (CMD) ................[AUTO] 

##Channel A Misc Timing Control##
Round Trip Latency ...................[AUTO] (59)

B2B CAS Delay ..........................[AUTO] (-)


Advanced Voltage Control:

CPU
Load Line Calibration ................. [AUTO]
CPU Vcore ...............................[AUTO] (1.13750V)
QPI/VTT Voltage 1.150v ............[1.400V]
CPU PLL 1.800v .......................[AUTO]

MCH/ICH
PCIE 1.500v ...........................[AUTO]
QPI PLL 1.100v .......................[1.200V]
IOH Core 1.100v .....................[1.140V]
ICH I/O 1.500v .......................[AUTO]
ICH Core 1.1v ........................[AUTO]

DRAM
DRAM Voltage 1.500v ..............[1.660V]
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

[REG1STRAT1ON]

Re: GA-X58A-UD5 memory issues :(



0x50 = RAM timings/Frequency or uncore multi unstable, increase RAM voltage or adjust QPI/VTT, or lower uncore if you're higher than 2x

Im assuming thats what i need to fiddle with

[Acebmxer]

Re: GA-X58A-UD5 memory issues :(

Correct.

It will also better help us to help you if you could be a detailed list of your hard in your sig like you see must of us have this way we can quickly reference to the hardware you are using.

[REG1STRAT1ON]

Re: GA-X58A-UD5 memory issues :(

Correct.

It will also better help us to help you if you could be a detailed list of your hard in your sig like you see must of us have this way we can quickly reference to the hardware you are using.

I think there may be a minimum posts thing before i can edit my signature as its missing from the "My Settings" menu in VBulletin.

Still no luck atm.

[REG1STRAT1ON]

Re: GA-X58A-UD5 memory issues :(

Upped the QPI and DRAM voltage a little higher - havnt blue screened as of yet - however i seem to get full system "lag spikes". My CPU is now running very hot idle 60C under 70% load on any of the cores will get it to 80C no problems.

Will grab an after market cooler - looking at a water based system thats fully closed (one that i dont have to fill up etc etc)

Can't do any stress testing or ram testing whilst the CPU is running so hot so not sure how stable it is right now. This is currently the longest it has been up - even doing simple tasks such as web browsing without blue screening.

[Acebmxer]

Re: GA-X58A-UD5 memory issues :(

There should be no minimum post for having or editing your sig.

Just click settings link in the very top left corner of the forum then click edit signature on the left mid way down.

[REG1STRAT1ON]

Re: GA-X58A-UD5 memory issues :(

Still havn't crashed at current settings - DRAM voltage is 1.7v - QPI voltage is 1.44v. Waiting for aftermarket cooler for real tests!

Thanks for all your help!

[Lsdmeasap]

Re: GA-X58A-UD5 memory issues :(

He needs to verify his account via email before he can access those settings. I'll resend the email to him now, check your spam box in case it goes there!