Tweet
Hello ,
I'm trying to boot my system @ 5.0 GHZ , but no success so far 4.7 is my max...
my setup :
Xeon W3550
GA EX58-Extreme
G.Skill DDR3 3x4gb 2133 1.65V 9-11-10-28
right now this is what im running:
Advanced CPU Features:
CPU Clock Ratio ................................ [21x]
Intel(R) Turbo Boost Tech .................. [Disabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Disabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled]
Bi-Directional PROCHOT ..................... [Enabled]
Uncore & QPI Features:
QPI Link Speed .............................. [Slow Mode]
Uncore Frequency .......................... [x16]
Isonchronous Frequency ................. [Enabled]
Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................[215]
PCI Express Frequency (MHz) ........... [100] **** I've read somewhere , that if i raise this more atleast +3 i can achieve higher BCLK and stable ... but if i go even one notch higher than 100 the pc wont even boot
C.I.A.2 [Disabled]
Advanced Clock Control:
CPU Clock Drive ..............................[900mV]
PCI Express Clock Drive ................... [800mV]
CPU Clock Skew ............................. [100ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Profile1]
Channel A + B + C
Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................8
tRCD ........................................10
tRP ..........................................9
tRAS .......................................25
##Channel A Advanced Timing Control##
tRC ........................................ [Auto]
tRRD ....................................... [Auto]
tWTR ...................................... [Auto]
tWR ........................................ [Auto]
tWTP .......................................[Auto]
tWL ........................................ [Auto]
tRFC ....................................... [Auto]
tRTP ....................................... [Auto]
tFAW ...................................... [Auto]
Command Rate (CMD) ................ [Auto]
##Channel A Misc Timing Control##
Round Trip Latency ...................[Auto]
B2B CAS Delay ..........................[Auto]
Advanced Voltage Control:
CPU
Load Line Calibration ................. [Enabled]
CPU Vcore ...............................1.225V [1.4500]
QPI/VTT Voltage 1.150v ............1.175V [1.440]
CPU PLL 1.800v ........................1.800V [1.880]
MCH/ICH
PCIE 1.500v ...........................[1.500]
QPI PLL 1.100v .......................[1.160]
IOH Core 1.100v .....................[1.200]
ICH I/O 1.500v .......................[Auto]
ICH Core 1.1v ........................[1.140]
DRAM
DRAM Voltage 1.500v ..............[1.700]
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]
*Don't mind the memory setting , i'm just trying to take it to the limit (temporary)
please any suggestions ?
I'm trying to boot my system @ 5.0 GHZ , but no success so far 4.7 is my max...
my setup :
Xeon W3550
GA EX58-Extreme
G.Skill DDR3 3x4gb 2133 1.65V 9-11-10-28
right now this is what im running:
Advanced CPU Features:
CPU Clock Ratio ................................ [21x]
Intel(R) Turbo Boost Tech .................. [Disabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Disabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled]
Bi-Directional PROCHOT ..................... [Enabled]
Uncore & QPI Features:
QPI Link Speed .............................. [Slow Mode]
Uncore Frequency .......................... [x16]
Isonchronous Frequency ................. [Enabled]
Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................[215]
PCI Express Frequency (MHz) ........... [100] **** I've read somewhere , that if i raise this more atleast +3 i can achieve higher BCLK and stable ... but if i go even one notch higher than 100 the pc wont even boot
C.I.A.2 [Disabled]
Advanced Clock Control:
CPU Clock Drive ..............................[900mV]
PCI Express Clock Drive ................... [800mV]
CPU Clock Skew ............................. [100ps]
IOH Clock Skew ............................. [0ps]
Advanced DRAM Features:
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Profile1]
Channel A + B + C
Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................8
tRCD ........................................10
tRP ..........................................9
tRAS .......................................25
##Channel A Advanced Timing Control##
tRC ........................................ [Auto]
tRRD ....................................... [Auto]
tWTR ...................................... [Auto]
tWR ........................................ [Auto]
tWTP .......................................[Auto]
tWL ........................................ [Auto]
tRFC ....................................... [Auto]
tRTP ....................................... [Auto]
tFAW ...................................... [Auto]
Command Rate (CMD) ................ [Auto]
##Channel A Misc Timing Control##
Round Trip Latency ...................[Auto]
B2B CAS Delay ..........................[Auto]
Advanced Voltage Control:
CPU
Load Line Calibration ................. [Enabled]
CPU Vcore ...............................1.225V [1.4500]
QPI/VTT Voltage 1.150v ............1.175V [1.440]
CPU PLL 1.800v ........................1.800V [1.880]
MCH/ICH
PCIE 1.500v ...........................[1.500]
QPI PLL 1.100v .......................[1.160]
IOH Core 1.100v .....................[1.200]
ICH I/O 1.500v .......................[Auto]
ICH Core 1.1v ........................[1.140]
DRAM
DRAM Voltage 1.500v ..............[1.700]
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]
*Don't mind the memory setting , i'm just trying to take it to the limit (temporary)
please any suggestions ?
Comment