Tweet
Re: Help me overclock my E7200--> All info included in OP
Thanks
Please start over before you use these settings!! You are using Fail Safe defaults and this is not good to start with, load Optimized Defaults and save/apply/reboot BACK to the BIOS, then set all your SATA/Disk settings again and any other settings you need to before loading windows again.
This is very important that you do not load windows again after doing that until you go back and set your SATA/Disk settings again, especially if you are using RAID.
Although my real suggestion to you would be to take care of all this at once by updating to the latest BIOS
GA-EP45-UD3P (rev. 1.0) - GIGABYTE - Support&Download - Motherboard - BIOS
DO NOT USE @BIOS!! Please use Qflash, here is a guide
In the update process you will do all of the above (Optimized Defaults process) anyway so you only need to do it once after you flash the BIOS.
Thanks
Please start over before you use these settings!! You are using Fail Safe defaults and this is not good to start with, load Optimized Defaults and save/apply/reboot BACK to the BIOS, then set all your SATA/Disk settings again and any other settings you need to before loading windows again.
This is very important that you do not load windows again after doing that until you go back and set your SATA/Disk settings again, especially if you are using RAID.
Although my real suggestion to you would be to take care of all this at once by updating to the latest BIOS
GA-EP45-UD3P (rev. 1.0) - GIGABYTE - Support&Download - Motherboard - BIOS
DO NOT USE @BIOS!! Please use Qflash, here is a guide
In the update process you will do all of the above (Optimized Defaults process) anyway so you only need to do it once after you flash the BIOS.
Code:
CPU Host Clock Control --------------- : [Enabled] CPU Multiplier ------------------------: [B]9.0[/B] CPU Host Frequency (Mhz) --------------: [266] << Set 401 PCI Express Frequency (Mhz) ---------- : [100] C.I.A.2 ------------------------------ : [Disabled] CPU Clock Drive ---------------------- : 700mv << Will be different once you load optimized PCI Express Clock Drive -------------- : 700mv << Will be different once you load optimized CPU Clock Skew (ps) ------------------ : 0ps MCH Clock Skew (ps) ------------------ : 0ps DRAM Performance Control Performance Enhance ------------------ : [Standard] Extreme Memory Profile --- (X.M.P.) -- : [Disabled] (G)MCH Frequency Latch --------------- : [Auto] System Memory Multiplier ------------- : [3.00A] << Set 2.00D Memory Frequency (Mhz) --------------- : [800] DRAM Timing Selectable --------------- : [Manual] Standard Timing Control CAS Latency Time -------- 5 ---------- : [5] tRCD -------------------- 5 ---------- : [5] tRP --------------------- 5 ---------- : [5] tRAS ------------------- 15 ---------- : [15] Advanced Timing Control tRRD -------------------- 3 ---------- : 3-4 tWTR -------------------- 3 ---------- :3-6 tWR --------------------- 6 ---------- : 4-6 tRFC ------------------- 52 ---------- : 52-62 tRTP -------------------- 3 ---------- : 3-5 Command Rate (CMD) ------ 0 ---------- : 2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................ 800 or 1066, try 1066 later but it may be best Channel A Static tRead Value --------------------- : 8-9 tRD Phase0 Adjustment ---------------- : [Auto] tRD Phase1 Adjustment ---------------- : [Auto] tRD Phase2 Adjustment ---------------- : [Auto] tRD Phase3 Adjustment ---------------- : [Auto] Trd2rd(Different Rank) --------------- : [Auto] Twr2wr(Different Rank) --------------- : [Auto] Twr2rd(Different Rank) --------------- : [Auto] Trd2wr(Same/Diff Rank) --------------- : [Auto] Dimm1 Clock Skew Control ------------- : [Auto] ps Dimm2 Clock Skew Control ------------- : [Auto] ps Channel B Static tRead Value ------------------- : 8-9 tRD Phase0 Adjustment ---------------- : [Auto] tRD Phase1 Adjustment ---------------- : [Auto] tRD Phase2 Adjustment ---------------- : [Auto] tRD Phase3 Adjustment ---------------- : [Auto] Trd2rd(Different Rank) --------------- : [Auto] Twr2wr(Different Rank) --------------- : [Auto] Twr2rd(Different Rank) --------------- : [Auto] Trd2wr(Same/Diff Rank) --------------- : [Auto] Dimm1 Clock Skew Control ------------- : [Auto] ps Dimm2 Clock Skew Control ------------- : [Auto] ps Load-Line Calibration ---------------- : [Disabled] << Enabled CPU Vcore --------------- 1.1000 ---- : [1.10000] << Set 1.225-1.35 CPU Termination --------- 1.200V* ---- : [1.200v] << may need 1.225-1.3 CPU PLL ----------------- 1.500V* ---- : [1.500v] << 1.5 may be fine, but you might need 1.55 or so CPU Reference ----------- 0.755V* ---- : [Auto] CPU Reference2 ---------- 0.800V* ---- : [Auto] MCH/ICH MCH Core ---------------- 1.100V ----- : [1.100] << Set 1.2-1.24 MCH Reference ----------- 0.800V ----- : [Auto] MCH/DRAM Ref ------------ 0.900V ---- : [Auto] ICH I/O ----------------- 1.500V ----- : [1.500] ICH Core ---------------- 1.100V ----- : [1.100] DRAM DRAM Voltage ------------ 1.800V ----- : [1.90] DRAM Termination -------- 0.900V ----- : [Auto] Channel A Reference ----- 0.900V ----- : [Auto] Channel B Reference ----- 0.900V ----- : [Auto] Advanced Settings Limit CPUID Max. to 3 ---------------- : [Disabled] No-Execute Memory Protect ------------ : [Enabled] CPU Enhanced Halt (C1E) -------------- : [Disabled] C2/C2E State Support ----------------- : [Disabled] x C4/C4E State Support --------------- : [Disabled] CPU Thermal Monitor 2 (TM2) ---------- : [Enabled] CPU EIST Function ------------------- : [Disabled] Virtualization Technology ------------ : [Disabled] Integrated Peripherals Legacy USB Storage Detect ----------- : [Disabled]
Comment