Tweet
Re: GA-EP45-UD3P - Q9550 not posting correctly...
Cool! Always great to hear that!
Try these for 3.6 for now then and see how you get along with overclocking, and how temps are under load once you find a good Vcore.
Cool! Always great to hear that!
Try these for 3.6 for now then and see how you get along with overclocking, and how temps are under load once you find a good Vcore.
Code:
[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] Robust Graphics Booster ...............: Auto or Fast CPU Clock Ratio ..........................: 8 Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: 3.6 [b][u]Clock Chip Control [/u][/b] [b][u]Standard Clock Control[/u][/b] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 450Mhz [B]PCI Express Frequency (Mhz) .........:Set to 100[/B] C.I.A.2 .................................:[Disabled] [b][u]Advanced Clock Control [Press Enter][/u][/b] CPU Clock Drive...........................: <<< 800 PCI Express Clock Drive.................: <<< 900 CPU Clock Skew (ps)....................: <<< MCH Clock Skew (ps)...................: <<< [b][u]DRAM Performance Control[/u][/b][u][/u] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [Auto] System Memory Multiplier ..............: 2.00D (Can try 2.00B or 2.40B later) Memory Frequency (Mhz) ..............: 900Mhz DRAM Timing Selectable ................: [Manual] [b]Standard Timing Control[/b] CAS Latency Time........................ 5 tRCD ......................................... 4/5 tRP'........................................... 4/5 tRAS.......................................... 12/15 Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go [b][u]Advanced Timing Control[/u][/b] tRRD........................................... 3-4 tWTR.......................................... 3-6 tWR............................................ 4-6 tRFC........................................... 52-62 tRTP........................................... 3-5 Command Rate (CMD) ....................:2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................ 1066 [b]Channel A[/b] Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Use 9 for now, lower later tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b]Channel B[/b] Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Use 9 for now, lower later tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b][U]Motherboard Voltage Control[/U][/b][U][/U] [b]CPU[/b] CPU Vcore….……….........................: All up to your CPU, maybe 1.25-1.38 would be enough. (Enable LLC - Load Line Calibration) CPU Termination…..... 1.200V*.......: << 1.225-1.34 should be plenty CPU PLL…………………....1.500V*.......: << 1.5-1.55 CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly [b]MCH/ICH[/b] MCH Core…………….....1.100V...........: << 1.2-1.24 MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.500V............: <<< Leave ICH Core…………...……1.100V............: <<< Leave [b]DRAM[/b] DRAM Voltage ……....1.800V............: 2.0-2.1 DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [b][U]Advanced Settings[/U][/b][U][/U] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [b][U]Integrated Peripherals[/U][/b][U][/U] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Comment