new to AMD but just got this board with a phenom ll x2 555. how do i unlock? also any o/c templates?
Announcement
Collapse
No announcement yet.
Ga-890gpa-ud3h o/c
Collapse
X
-
Re: Ga-890gpa-ud3h o/c
Hi race301 What do you want to work on first RAID? http://forums.tweaktown.com/f69/ga-8...se-help-38942/ or OC? Unlocking cores? Find Advanced Clock Calibration (ACC) function in your bios. http://www.xbitlabs.com/articles/cpu...-ii-x2_15.html
Have you flashed your bios yet? http://www.gigabyte.com.tw/Support/M...ctID=3342&ver=
Below is a PDF of your motherboard manual. It may take a bit to download. http://download.gigabyte.ru/manual/m...gpa-ud3h_e.pdfLast edited by artdrivers; 04-02-2010, 08:42 PM.http://forums.tweaktown.com/gigabyte...ench-test.html
http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
Gigabyte GA-MA78GM-S2H rev.1.1 F11
Sapphire 3870HD / 100225L / 512MB / ddr4
4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
(2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
(1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
(2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
Antec /Neo HE550 / 550W
Mid size ATX case with show through panel
2) 80x80 front fans (1) 120x120 rear fan and small nb fan
Microsoft comfort curve USB keyboard 2000 ver.1.0
Logitech G500 USB mouse
Monitor: CMV937A
7.1+2 Channel High Definition ALC889A
Dual boot Windows 7 32bit home & Windows 7 64bit home
Comment
-
Re: Ga-890gpa-ud3h o/c
I already have W7 64b loaded on a 650 WD drive, so o/c for now. :) First AMD I have owned. Thanks in advance.
I have this ram http://www.newegg.com/Product/Produc...82E16820227483
Comment
-
Re: Ga-890gpa-ud3h o/c
Could we start with a picture of your PC health? Below is a template of it for you to copy your bios temps, voltages, and fan settings to it. I believe this is a good place to start. When you first go into bios set it to load optimized defaults. Save and exit. Reboot back into bios for readings.
Code:PC Health Status Hardware Thermal Control [Enabled] Reset Case Open Status [Disabled] Case Opened No Vcore 1.364V DDR3 1.5V 1.536V +3.3V 3.280V +12V 12.048V Current System Temperature 38oC Current CPU Temperature 36oC Current CPU FAN Speed 1962 RPM Current SYSTEM FAN1 Speed 0 RPM Current SYSTEM FAN2 Speed 0 RPM Current POWER FAN Speed 0 RPM CPU Warning Temperature [Disabled] CPU FAN Fail Warning [Disabled] SYSTEM FAN1 Fail Warning [Disabled] SYSTEM FAN2 Fail Warning [Disabled] POWER FAN Fail Warning [Disabled] CPU Smart FAN Control [Enabled] CPU Smart FAN Mode [Auto] System Smart FAN Control [Enabled]
Code:MB Intelligent Tweaker(M.I.T.) } IGX Configuration [Press Enter] CPU Clock Ratio [Auto] 2800Mhz CPU NorthBridge Freq. [Auto] 2000Mhz CPU Host Clock Control [Auto] x CPU Frequency(MHz) 200 PCIE Clock(MHz) [Auto] HT Link Width [Auto] HT Link Frequency [Auto] 2000Mhz Set Memory Clock [Auto] x Memory Clock x6.66 1333Mhz } DRAM Configuration [[COLOR="darkred"]Press Enter[/COLOR]] ******** System Voltage Optimized ******** System Voltage Control [Auto] x CPU PLL Voltage Control Auto x DRAM Voltage Control Auto x DDR VTT Voltage Control [COLOR="darkred"]manual[/COLOR] x NB Voltage Control [COLOR="darkred"]manual[/COLOR] x SidePort Mem Volt Control [COLOR="darkred"]manua[/COLOR]l x NB/PCIe/PLL Voltage Control [COLOR="darkred"]manual[/COLOR] x CPU NB VID Control [COLOR="darkred"]manual[/COLOR] x CPU Voltage Control Auto Normal CPU Vcore 1.3250V
Code:DRAM Configuration DCTs Mode [Unganged] DDR3 Timing Items [[COLOR="darkred"]manual[/COLOR]] SPD Auto x CAS# latency Auto 9T 9T x RAS to CAS R/W Delay Auto 9T 9T x Row Precharge Time Auto 9T 9T x Minimum RAS Active Time Auto 24T 24T x 1T/2T Command Timing Auto -- -- x TwTr Command Delay Auto 5T 5T x Trfc0 for DIMM1 Auto 110ns 110ns x Trfc2 for DIMM2 Auto -- -- x Trfc1 for DIMM3 Auto -- -- x Trfc3 for DIMM4 Auto -- -- x Write Recovery Time Auto 10T 10T x Precharge Time Auto 5T 5T x Row Cycle Time Auto 33T 33T x RAS to RAS Delay Auto 4T 4T **DCTs Drive Strength** DCT0 DCT1 ProcOdt(ohms) [Auto] 60 [Auto] 60 DQS drive Strength [Auto] 1.0x [Auto] 1.0x Data drive Strength [Auto] 1.0x [Auto] 1.0x MEMCLK drive Strength [Auto] 1.25x [Auto] 1.25x Addr/Cmd drive Strength [Auto] 1.5x [Auto] 1.5x CS/ODT drive Strength [Auto] 1.5x [Auto] 1.5x CKE drive Strength [Auto] 1.5x [Auto] 1.5x Bank Interleaving [Enabled] Channel interleave [Enabled]
We will get back to you later with changes. After we have a chance to see your bios readings. OK?http://forums.tweaktown.com/gigabyte...ench-test.html
http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
Gigabyte GA-MA78GM-S2H rev.1.1 F11
Sapphire 3870HD / 100225L / 512MB / ddr4
4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
(2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
(1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
(2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
Antec /Neo HE550 / 550W
Mid size ATX case with show through panel
2) 80x80 front fans (1) 120x120 rear fan and small nb fan
Microsoft comfort curve USB keyboard 2000 ver.1.0
Logitech G500 USB mouse
Monitor: CMV937A
7.1+2 Channel High Definition ALC889A
Dual boot Windows 7 32bit home & Windows 7 64bit home
Comment
-
Re: Ga-890gpa-ud3h o/c
Put mine next to yours
Originally posted by artdrivers View PostCould we start with a picture of your PC health? Below is a template of it for you to copy your bios temps, voltages, and fan settings to it. I believe this is a good place to start. When you first go into bios set it to load optimized defaults. Save and exit. Reboot back into bios for readings.
Code:PC Health Status Hardware Thermal Control [Enabled] Reset Case Open Status [Disabled] Case Opened No yes Vcore 1.364V 1.472 DDR3 1.5V 1.536V 1.488 +3.3V 3.280V 3.344 +12V 12.048V 12.175 Current System Temperature 38oC 36 Current CPU Temperature 36oC 28 Current CPU FAN Speed 1962 RPM 1011 Current SYSTEM FAN1 Speed 0 RPM Current SYSTEM FAN2 Speed 0 RPM Current POWER FAN Speed 0 RPM CPU Warning Temperature [Disabled] CPU FAN Fail Warning [Disabled] SYSTEM FAN1 Fail Warning [Disabled] SYSTEM FAN2 Fail Warning [Disabled] POWER FAN Fail Warning [Disabled] CPU Smart FAN Control [Enabled] CPU Smart FAN Mode [Auto] System Smart FAN Control [Enabled]
Code:MB Intelligent Tweaker(M.I.T.) } IGX Configuration [Press Enter] CPU Clock Ratio [Auto] 2800Mhz 3200 CPU NorthBridge Freq. [Auto] 2000Mhz CPU Host Clock Control [Auto] x CPU Frequency(MHz) 200 PCIE Clock(MHz) [Auto] HT Link Width [Auto] HT Link Frequency [Auto] 2000Mhz Set Memory Clock [Auto] x Memory Clock x6.66 1333Mhz x5.33 1066 } DRAM Configuration [[COLOR="darkred"]Press Enter[/COLOR]] ******** System Voltage Optimized ******** System Voltage Control [Auto] x CPU PLL Voltage Control Auto x DRAM Voltage Control Auto x DDR VTT Voltage Control [COLOR="darkred"]manual[/COLOR] x NB Voltage Control [COLOR="darkred"]manual[/COLOR] x SidePort Mem Volt Control [COLOR="darkred"]manua[/COLOR]l x NB/PCIe/PLL Voltage Control [COLOR="darkred"]manual[/COLOR] x CPU NB VID Control [COLOR="darkred"]manual[/COLOR] x CPU Voltage Control Auto Normal CPU Vcore 1.3250V
One more while we are here. For this one you will need to change timing items from auto to manual, save and exit reboot into bios and read the timing items put them on a change the auto's on the template and post all of these results.
Code:DRAM Configuration DCTs Mode [Unganged] DDR3 Timing Items [[COLOR="darkred"]manual[/COLOR]] SPD Auto x CAS# latency Auto 9T 9T 7t x RAS to CAS R/W Delay Auto 9T 9T 7t x Row Precharge Time Auto 9T 9T 7t x Minimum RAS Active Time Auto 24T 24T 30 x 1T/2T Command Timing Auto -- -- x TwTr Command Delay Auto 5T 5T 4t x Trfc0 for DIMM1 Auto 110ns 110ns x Trfc2 for DIMM2 Auto -- -- 110ns x Trfc1 for DIMM3 Auto -- -- x Trfc3 for DIMM4 Auto -- -- x Write Recovery Time Auto 10T 10T 8t x Precharge Time Auto 5T 5T 4t x Row Cycle Time Auto 33T 33T 27t x RAS to RAS Delay Auto 4T 4T 4t **DCTs Drive Strength** DCT0 DCT1 ProcOdt(ohms) [Auto] 60 [Auto] 60 60 240 DQS drive Strength [Auto] 1.0x [Auto] 1.0x 1.25 1.5 Data drive Strength [Auto] 1.0x [Auto] 1.0x 1.25 1.5 MEMCLK drive Strength [Auto] 1.25x [Auto] 1.25x 1.5 1.5 Addr/Cmd drive Strength [Auto] 1.5x [Auto] 1.5x 2.0 2.0 CS/ODT drive Strength [Auto] 1.5x [Auto] 1.5x 1.5 2.0 CKE drive Strength [Auto] 1.5x [Auto] 1.5x 2.0 2.0 Bank Interleaving [Enabled] Channel interleave [Enabled]
We will get back to you later with changes. After we have a chance to see your bios readings. OK?
Comment
-
Re: Ga-890gpa-ud3h o/c
This may be better
Comment
-
Code:PC Health Status Hardware Thermal Control [Enabled] Reset Case Open Status [Disabled] Case Opened No yes Vcore 1.364V 1.472 DDR3 1.5V 1.536V 1.488 +3.3V 3.280V 3.344 +12V 12.048V 12.175 Current System Temperature 38oC 36 Current CPU Temperature 36oC 28 Current CPU FAN Speed 1962 RPM 1011 Current SYSTEM FAN1 Speed 0 RPM Current SYSTEM FAN2 Speed 0 RPM Current POWER FAN Speed 0 RPM CPU Warning Temperature [[COLOR="darkred"]70oC/158oF[/COLOR]] CPU FAN Fail Warning [Disabled] SYSTEM FAN1 Fail Warning [Disabled] SYSTEM FAN2 Fail Warning [Disabled] POWER FAN Fail Warning [Disabled] CPU Smart FAN Control [Enabled] CPU Smart FAN Mode [Auto] System Smart FAN Control [Enabled]
You don't so we will be adjusting the cpu frequency which is a little more tricky. It will change the memory, northbridge, and HT Link frequencies at the same time. So we need to calibrate these settings as well. The best way is set the memory, northbridge, and HT Link multipliers down a little to adjust for the much higher overall frequency which they call cpu frequency. I will supply minor tweeks on voltage as well.
Code:MB Intelligent Tweaker(M.I.T.) } IGX Configuration [Press Enter] CPU Clock Ratio [Auto] 2800Mhz 3200 CPU NorthBridge Freq. [[COLOR="darkred"]9X or 18x[/COLOR]] [COLOR="darkred"]1800[/COLOR]Mhz CPU Host Clock Control [[COLOR="darkred"]Manual[/COLOR]] x CPU Frequency(MHz) [COLOR="darkred"]240[/COLOR] PCIE Clock(MHz) [Auto] HT Link Width [Auto] HT Link Frequency [[COLOR="darkred"]Manual[/COLOR]] 1800Mhz Set Memory Clock [[COLOR="darkred"]manual[/COLOR]] x Memory Clock x6.66 1333Mhz [COLOR="darkred"] x6.66 1333Mhz[/COLOR] } DRAM Configuration [Press Enter] ******** System Voltage Optimized ******** System Voltage Control [[COLOR="darkred"]Manual[/COLOR]] x CPU PLL Voltage Control Auto x DRAM Voltage Control [COLOR="darkred"]+0.15=1.65v[/COLOR] x DDR VTT Voltage Control [COLOR="darkred"]auto[/COLOR] x NB Voltage Control [COLOR="darkred"]auto[/COLOR] x SidePort Mem Volt Control [COLOR="darkred"]auto[/COLOR] x NB/PCIe/PLL Voltage Control [COLOR="darkred"]auto[/COLOR] x CPU NB VID Control [COLOR="darkred"]auto[/COLOR] x CPU Voltage Control Auto Normal CPU Vcore 1.3250V
Last edited by artdrivers; 04-03-2010, 08:15 PM.http://forums.tweaktown.com/gigabyte...ench-test.html
http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
Gigabyte GA-MA78GM-S2H rev.1.1 F11
Sapphire 3870HD / 100225L / 512MB / ddr4
4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
(2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
(1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
(2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
Antec /Neo HE550 / 550W
Mid size ATX case with show through panel
2) 80x80 front fans (1) 120x120 rear fan and small nb fan
Microsoft comfort curve USB keyboard 2000 ver.1.0
Logitech G500 USB mouse
Monitor: CMV937A
7.1+2 Channel High Definition ALC889A
Dual boot Windows 7 32bit home & Windows 7 64bit home
Comment
-
-
-
Re: Ga-890gpa-ud3h o/c
Awesome OC but you may want to set Dram voltage control to 1.5v +.15 = 1.65V and set Row Cycle Time to 32T 8+8+8+24=32T. Then try Prime 95 torture test http://mersenneforum.org/gimps/p64v2511.zip
See how long you can go without errors, but watch temperatures. I use HWmonitor for eyeing voltage and temperatures in Windows. http://www.cpuid.com/download/hwmoni...itor64_115.zip
These and other programs can be found here.
http://forums.tweaktown.com/gigabyte...ench-test.html
http://www.gigabyte-usa.com/FileList...ios_qflash.pdf
Phenom II 945 @ 3.2Ghz w/Thermaltake Big Typhoon Pro 14 CPU Cooler
Gigabyte GA-MA78GM-S2H rev.1.1 F11
Sapphire 3870HD / 100225L / 512MB / ddr4
4GB / Kingston / KHX8500D2K2/2GN / 5-5-5-18 / 1066Mhz
(2) WD Caviar / WD2500AAKS/ 250GB in SATA RAID-0
(1) WD Caviar / WD2500AAKS/ 250GB in SATA AHCI
(2) IDE's 1 8XdualDVDRW 1 52x32x52x CDRW
Antec /Neo HE550 / 550W
Mid size ATX case with show through panel
2) 80x80 front fans (1) 120x120 rear fan and small nb fan
Microsoft comfort curve USB keyboard 2000 ver.1.0
Logitech G500 USB mouse
Monitor: CMV937A
7.1+2 Channel High Definition ALC889A
Dual boot Windows 7 32bit home & Windows 7 64bit home
Comment
Comment