Hi guys,
I'm having trouble setting my memory (CORSAIR 1600C7DHX 2x1 GB DDR3) to run at 1600 MHz using Gigabyte EP45T-DS3R and Intel Q9450.
I've set the FSB to 400 MHz and the multiplier at 4 but i keep getting triple boot failure.
Please help me out
This is the link to my memory information
Motherboard: EP45T-DS3R: Rev#: latest:
Cpu: Q9450
Power Supply Unit: Corsair, Model#, Wattage 650 W
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [8x]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: 3200 <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [?400]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Enabled]
Advanced Clock Control ------- [Press Enter] //don't know what this is so i left it as it is
CPU Clock Drive ---------------------- : [???]
PCI Express Clock Drive -------------- : [???]
CPU Clock Skew (ps) ------------------ : [???]
MCH Clock Skew (ps) ------------------ : [???]
DRAM Performance Control
Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [4] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [1600]
DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [7]
tRCD ------------------- ?? ---------- : [7]
tRP --------------------- ?? ---------- : [7]
tRAS ------------------- ?? ---------- : [20]
Advanced Timing Control // also don't know what this does
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- ?.????? ---- : [Auto]
CPU Termination --------- ?.???V* ----- : [Auto]
CPU PLL ----------------- ?.???V* ----- : [Auto]
CPU Reference ----------- ?.???V* ----- : [Auto]
CPU Reference2 ---------- ?.???V* ----- : [Auto]
MCH/ICH
MCH Core ---------------- ?.???V ------- : [Auto]
MCH Reference ----------- ?.???V ------- : [Auto]
MCH/DRAM Ref ------------ ?.???V ------ : [Auto]
ICH I/O ----------------- ?.???V ------- : [Auto]
ICH Core ---------------- ?.???V ------- : [Auto]
DRAM
DRAM Voltage ------------ ?.???V ------- : [1.9]
DRAM Termination -------- ?.???V ------- : [Auto]
Channel A Reference ----- ?.???V ------- : [Auto]
Channel B Reference ----- ?.???V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]
I'm having trouble setting my memory (CORSAIR 1600C7DHX 2x1 GB DDR3) to run at 1600 MHz using Gigabyte EP45T-DS3R and Intel Q9450.
I've set the FSB to 400 MHz and the multiplier at 4 but i keep getting triple boot failure.
Please help me out
This is the link to my memory information
Motherboard: EP45T-DS3R: Rev#: latest:
Cpu: Q9450
Power Supply Unit: Corsair, Model#, Wattage 650 W
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [8x]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: 3200 <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [?400]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Enabled]
Advanced Clock Control ------- [Press Enter] //don't know what this is so i left it as it is
CPU Clock Drive ---------------------- : [???]
PCI Express Clock Drive -------------- : [???]
CPU Clock Skew (ps) ------------------ : [???]
MCH Clock Skew (ps) ------------------ : [???]
DRAM Performance Control
Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [4] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [1600]
DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [7]
tRCD ------------------- ?? ---------- : [7]
tRP --------------------- ?? ---------- : [7]
tRAS ------------------- ?? ---------- : [20]
Advanced Timing Control // also don't know what this does
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- ?.????? ---- : [Auto]
CPU Termination --------- ?.???V* ----- : [Auto]
CPU PLL ----------------- ?.???V* ----- : [Auto]
CPU Reference ----------- ?.???V* ----- : [Auto]
CPU Reference2 ---------- ?.???V* ----- : [Auto]
MCH/ICH
MCH Core ---------------- ?.???V ------- : [Auto]
MCH Reference ----------- ?.???V ------- : [Auto]
MCH/DRAM Ref ------------ ?.???V ------ : [Auto]
ICH I/O ----------------- ?.???V ------- : [Auto]
ICH Core ---------------- ?.???V ------- : [Auto]
DRAM
DRAM Voltage ------------ ?.???V ------- : [1.9]
DRAM Termination -------- ?.???V ------- : [Auto]
Channel A Reference ----- ?.???V ------- : [Auto]
Channel B Reference ----- ?.???V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]
Comment