Tweet
Re: EP45T-USB3P problem with PSU
Try the following changes for 3.8GHz.
Remember to 2-3 passes of memtest86+ before attemting to run windows.
Any clarifications needed, just ask.
Try the following changes for 3.8GHz.
Remember to 2-3 passes of memtest86+ before attemting to run windows.
Any clarifications needed, just ask.
Code:
MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster --------------- : [Fast] CPU Clock Ratio ----------------------- : [8x] Fine CPU Clock Ratio ------------------ : [0.0] CPU Frequency ------------------------- : [3.60GHz(450x8)] Clock Chip Control Standard Clock Control CPU Host Clock Control ---------------- : [Enabled] CPU Host Frequency (Mhz) ---------------: [[COLOR=red][B]450[/B][/COLOR]] PCI Express Frequency (Mhz) ----------- : [100] C.I.A.2 ------------------------------- : [Disabled] Advanced Clock Control -------- [Press Enter] CPU Clock Drive ----------------------- : 800 PCI Express Clock Drive --------------- : 900 CPU Clock Skew (ps) ------------------- : 0ps MCH Clock Skew (ps) ------------------- : 0ps DRAM Performance Control Performance Enhance -------- (SPD) ---- : [Standard] Extreme Memory Profile --- (X.M.P.) --- : [Profile 1] (G)MCH Frequency Latch ----- (SPD) ---- : [Auto] System Memory Multiplier -------------- : [3.33D] [COLOR=darkred]<<< 2.66D, 3.20B or others if fail[/COLOR] Memory Frequency (Mhz) ------[1600]---- : [1500] DRAM Timing Selectable ---------------- : [Manual] Standard Timing Control CAS Latency Time -------- [7] --------- : [[COLOR=red][B]7[/B][/COLOR]] tRCD ------------------- [8] --------- : [[B][COLOR=red]8[/COLOR][/B]] tRP --------------------- [7] --------- : [[COLOR=red][B]7[/B][/COLOR]] tRAS ------------------ [24] --------- : [[COLOR=red][B]24[/B][/COLOR]] Advanced Timing Control tRRD ------------------- [5] --------- : [Auto] tWTR ------------------- [6] --------- : [Auto] tWR ---------------------[12] --------- : [Auto] tRFC -------------------[88] --------- : [Auto] tRTP --------------------[6] --------- : [Auto] Command Rate (CMD) -------[0] --------- : [Auto] Driving Strength Profiles Driving Strength ---------- [Auto only] : [Auto] Channel A Static tRead Value ---------------- [9] : [[COLOR=red][B]10[/B][/COLOR]] <<< lower later Auto everything below Channel B Static tRead Value ---------------- [9] : [[B][COLOR=red]10[/COLOR][/B]] <<< lower later Auto everything below Motherboard Voltage Control CPU Voltage Types------------ Normal -------- Current --- Load-Line Calibration ----------------- : [Disabled] CPU Vcore --------------- 1.27500v ---- : [1.325] [COLOR=darkred]<<< a step or two up "just in case"[/COLOR] CPU Termination --------- 1.200V* ----- : [1.260] CPU PLL ----------------- 1.500V* ----- : [1.500] [COLOR=darkred]<<< may increase one step up[/COLOR] CPU Reference ----------- 0.760V* ----- : [Auto] [COLOR=darkred]<<< may need adjusment[/COLOR] CPU Reference2 ---------- 0.800V* ----- : [Auto] MCH/ICH MCH Core ---------------- 1.100V ------- : [1.240] [COLOR=darkred]<<< more may be needed 1.26-.128v[/COLOR] MCH Reference ----------- 0.760V ------- : [Auto] [COLOR=darkred]<<< this may need adjusment, try 0.74/0.72/0.70 @ 1.2VTT before raising MCH Core[/COLOR] MCH/DRAM Ref ------------ 0.750V ------ : [Auto] ICH I/O ----------------- 1.500V ------- : [1.500] ICH Core ---------------- 1.100V ------- : [1.100] DRAM DRAM Voltage ------------ 1.500V ------- : [1.35] DRAM Termination -------- 0.750V ------- : [Auto] Ch-A Data VRef.---------- 0.750v ------- : [Auto] Ch-B Data VRef.---------- 0.750v ------- : [Auto] Ch-A Address Ref.-------- 0.750v ------- : [Auto] Ch-B Address Ref.-------- 0.750v ------- : [Auto]
Comment