I'm going to post as much information as possible so hopefully it will help get me some answers. This was my first system build and I kinda just went with it in terms of getting things running. My problem is that I will constantly get a system lock which requires a power off. Sometimes it boots right up and I can resume. Other times, I'll power on and be stuck in a bootloop or the BIOS will simply stop. Sometimes there will be text fragments and articles over the screen which is the only visible sign indication of a problem. I can't recall when these problems started, but I don't remember them occurring too soon after initial build. I'd like to think that it's due to using 4 sticks of RAM and that partially because I don't have something set correctly.
System specs: (built August 2008)
Gigabyte EP45T-DS3R (F2 bios) Rev 1.0
Intel E8500 Wolfdale 3.16ghz
OCZ3P13334GK - OCZ Platinum DDR3 1333 (4x2GB)
ATI Radeon 4870 1GB
Found the P45 template which I'm going to fill in. I imagine there's probably a host of issues with my settings as I'm really not to privy to some of these fields and their direct correlation to the :
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .............: Auto
CPU Clock Ratio .....................: 9x
Fine CPU Clock Ratio.................: 0.5
CPU Frequency .......................: 3.16 (333 x 9.5)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control...............: [Enabled]
CPU Host Frequency (Mhz) ............: 333 Mhz
PCI Express Frequency (Mhz) .........: Auto
C.I.A.2 .............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive......................: 800
PCI Express Clock Drive..............: 900
CPU Clock Skew (ps)..................: 0
MCH Clock Skew (ps)..................: 0
DRAM Performance Control
Performance Enhance..................: [Turbo]
Extreme Memory Profile (X.M.P.)......: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ............: Auto
Memory Frequency (Mhz) ..............: 1333
DRAM Timing Selectable ..............: [Auto]
Standard Timing Control
CAS Latency Time.....................: 7
tRCD ................................: 7
tRP'.................................: 7
tRAS.................................: 20
Advanced Timing Control
tRRD.................................: 4
tWTR.................................: 5
tWR..................................: 10
tRFC.................................: 60
tRTP.................................: 5
Command Rate (CMD) ..................: 0
Channel A
Static tRead Value...................: 6
tRD Phase0 Adjustment................: 0
tRD Phase1 Adjustment................: 0
tRD Phase2 Adjustment ...............: 1
tRD Phase3 Adjustment................: 1
Trd2rd(Different Rank)...............: 7
Twr2wr(Different Rank)...............: 7
Twr2rd(Different Rank)...............: 8
Trd2wr(Same/Diff Rank)...............: 9
Channel B
Static tRead Value...................: 6
tRD Phase0 Adjustment................: 0
tRD Phase1 Adjustment................: 0
tRD Phase2 Adjustment ...............: 1
tRD Phase3 Adjustment................: 1
Trd2rd(Different Rank)...............: 7
Twr2wr(Different Rank)...............: 7
Twr2rd(Different Rank)...............: 8
Trd2wr(Same/Diff Rank)...............: 9
Motherboard Voltage Control
CPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)..............: [Disabled]
C2/C2E State Support.................: [Disabled]
x C4/C4E State Support...............: [Disabled]
CPU Thermal Monitor 2(TM2) ..........: [Enabled]
CPU EIST Function....................: [Disabled]
Virtualization Technology............: [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ...........: [Enabled]</pre>
As I write this, I am in one of my non-boot phases (posting from laptop). Power on, single beep, nada. Power on, single beep, show mobo info, show processor info, freeze. And I could type the many different scenarios.
So, can this be fixed?
System specs: (built August 2008)
Gigabyte EP45T-DS3R (F2 bios) Rev 1.0
Intel E8500 Wolfdale 3.16ghz
OCZ3P13334GK - OCZ Platinum DDR3 1333 (4x2GB)
ATI Radeon 4870 1GB
Found the P45 template which I'm going to fill in. I imagine there's probably a host of issues with my settings as I'm really not to privy to some of these fields and their direct correlation to the :
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .............: Auto
CPU Clock Ratio .....................: 9x
Fine CPU Clock Ratio.................: 0.5
CPU Frequency .......................: 3.16 (333 x 9.5)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control...............: [Enabled]
CPU Host Frequency (Mhz) ............: 333 Mhz
PCI Express Frequency (Mhz) .........: Auto
C.I.A.2 .............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive......................: 800
PCI Express Clock Drive..............: 900
CPU Clock Skew (ps)..................: 0
MCH Clock Skew (ps)..................: 0
DRAM Performance Control
Performance Enhance..................: [Turbo]
Extreme Memory Profile (X.M.P.)......: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ............: Auto
Memory Frequency (Mhz) ..............: 1333
DRAM Timing Selectable ..............: [Auto]
Standard Timing Control
CAS Latency Time.....................: 7
tRCD ................................: 7
tRP'.................................: 7
tRAS.................................: 20
Advanced Timing Control
tRRD.................................: 4
tWTR.................................: 5
tWR..................................: 10
tRFC.................................: 60
tRTP.................................: 5
Command Rate (CMD) ..................: 0
Channel A
Static tRead Value...................: 6
tRD Phase0 Adjustment................: 0
tRD Phase1 Adjustment................: 0
tRD Phase2 Adjustment ...............: 1
tRD Phase3 Adjustment................: 1
Trd2rd(Different Rank)...............: 7
Twr2wr(Different Rank)...............: 7
Twr2rd(Different Rank)...............: 8
Trd2wr(Same/Diff Rank)...............: 9
Channel B
Static tRead Value...................: 6
tRD Phase0 Adjustment................: 0
tRD Phase1 Adjustment................: 0
tRD Phase2 Adjustment ...............: 1
tRD Phase3 Adjustment................: 1
Trd2rd(Different Rank)...............: 7
Twr2wr(Different Rank)...............: 7
Twr2rd(Different Rank)...............: 8
Trd2wr(Same/Diff Rank)...............: 9
Motherboard Voltage Control
CPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)..............: [Disabled]
C2/C2E State Support.................: [Disabled]
x C4/C4E State Support...............: [Disabled]
CPU Thermal Monitor 2(TM2) ..........: [Enabled]
CPU EIST Function....................: [Disabled]
Virtualization Technology............: [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ...........: [Enabled]</pre>
As I write this, I am in one of my non-boot phases (posting from laptop). Power on, single beep, nada. Power on, single beep, show mobo info, show processor info, freeze. And I could type the many different scenarios.
So, can this be fixed?
Comment