Hi there, some of you might be aware I was having some OC stability problems. Well I seem to of fixed them and I have no crashes in games and everything seems to be running fine.
My system is 20 hours prime stable using Small AND Large tests.
I used default settings after installing prime and just ran the 2 tests seperatly. I ran the small FTF test twice both times going for 20 hours.
I stopped it after 20 hours and had no errors. My temps topped out at 76, but were generally lower around 70 most of the time.
My temps during Intel burn test were alot higher. Topping out at 86
My system also passed the Intel burn test of 5 passes using maximum stress level.
Ive taken some screenshots and ill post my complete bios settings, Could you please give me some advice if you think voltages are way too high or anything should be lowered. Or if any of the below settings should be changed. Or if you think I should push the system even more. Thanks.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [TURBO]
CPU Clock Ratio ---------------------- : [10X]
Fine CPU Clock Ratio ----------------- : [0.0]
CPU Frequency ---------------------: 4.0GHZ 10X400
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [400]
PCI Express Frequency (Mhz) ---------- : [100]
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [800mv]
PCI Express Clock Drive -------------- : [900mv]
CPU Clock Skew (ps) ------------------ : [0ps]
MCH Clock Skew (ps) ------------------ : [0ps]
DRAM Performance Control
Performance Enhance ------------------- : [Turbo]
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [2.00d
Memory Frequency (Mhz) ---------------- : [800]
DRAM Timing Selectable ---------------- : [Manual]
Standard Timing Control
CAS Latency Time -------- 5 ---------- : [5]
tRCD ------------------- 5 ---------- : [5]
tRP --------------------- 5 ---------- : [5]
tRAS ------------------- 15 ---------- : [15]
Advanced Timing Control
tRRD ------------------- 3 ---------- : [Auto]
tWTR ------------------- 3 ---------- : [Auto]
tWR --------------------- 6 ---------- : [Auto]
tRFC ------------------- 52 ---------- : [Auto]
tRTP ------------------- 3 ---------- : [Auto]
Command Rate (CMD) ----- 0 ------------ : [Auto]
Channel A
Static tRead Value --------- 9 --------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value -------- 9 ---------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto]
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
Load-Line Calibration ----------------- : [Enabled]
CPU Vcore --------------- 1.28750v ---- : [1.36875]
CPU Termination --------- 1.200v ----- : [1.240v]
CPU PLL ----------------- 1.500v ----- : [1.500v]
CPU Reference ----------- 0.760v ----- : [0.785v]
MCH/ICH
MCH Core ---------------- 1.100V ------- : [1.300v]
MCH Reference ----------- 0.760V ------- : [.765v]
MCH/DRAM Ref ------------ 0.900V ------- : [0.970v]
ICH I/O ----------------- 1.500V ------- : [Auto]
ICH Core ---------------- 1.100V ------- : [Auto]
DRAM
DRAM Voltage ------------ 1.800V ------- : [2.00v]
DRAM Termination -------- 0.900V ------- : [0.910v]
Channel A Reference ----- 0.900V ------- : [0.910v]
Channel B Reference ----- 0.900V ------- : [0.910v]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function ---------------------- : [Enabled]
Virtualization Technology -------------- : [Disabled]
and heres a screenshot with EIST Disabled, sorry bout that.
My system is 20 hours prime stable using Small AND Large tests.
I used default settings after installing prime and just ran the 2 tests seperatly. I ran the small FTF test twice both times going for 20 hours.
I stopped it after 20 hours and had no errors. My temps topped out at 76, but were generally lower around 70 most of the time.
My temps during Intel burn test were alot higher. Topping out at 86
My system also passed the Intel burn test of 5 passes using maximum stress level.
Ive taken some screenshots and ill post my complete bios settings, Could you please give me some advice if you think voltages are way too high or anything should be lowered. Or if any of the below settings should be changed. Or if you think I should push the system even more. Thanks.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [TURBO]
CPU Clock Ratio ---------------------- : [10X]
Fine CPU Clock Ratio ----------------- : [0.0]
CPU Frequency ---------------------: 4.0GHZ 10X400
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [400]
PCI Express Frequency (Mhz) ---------- : [100]
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [800mv]
PCI Express Clock Drive -------------- : [900mv]
CPU Clock Skew (ps) ------------------ : [0ps]
MCH Clock Skew (ps) ------------------ : [0ps]
DRAM Performance Control
Performance Enhance ------------------- : [Turbo]
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [2.00d
Memory Frequency (Mhz) ---------------- : [800]
DRAM Timing Selectable ---------------- : [Manual]
Standard Timing Control
CAS Latency Time -------- 5 ---------- : [5]
tRCD ------------------- 5 ---------- : [5]
tRP --------------------- 5 ---------- : [5]
tRAS ------------------- 15 ---------- : [15]
Advanced Timing Control
tRRD ------------------- 3 ---------- : [Auto]
tWTR ------------------- 3 ---------- : [Auto]
tWR --------------------- 6 ---------- : [Auto]
tRFC ------------------- 52 ---------- : [Auto]
tRTP ------------------- 3 ---------- : [Auto]
Command Rate (CMD) ----- 0 ------------ : [Auto]
Channel A
Static tRead Value --------- 9 --------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value -------- 9 ---------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto]
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
Load-Line Calibration ----------------- : [Enabled]
CPU Vcore --------------- 1.28750v ---- : [1.36875]
CPU Termination --------- 1.200v ----- : [1.240v]
CPU PLL ----------------- 1.500v ----- : [1.500v]
CPU Reference ----------- 0.760v ----- : [0.785v]
MCH/ICH
MCH Core ---------------- 1.100V ------- : [1.300v]
MCH Reference ----------- 0.760V ------- : [.765v]
MCH/DRAM Ref ------------ 0.900V ------- : [0.970v]
ICH I/O ----------------- 1.500V ------- : [Auto]
ICH Core ---------------- 1.100V ------- : [Auto]
DRAM
DRAM Voltage ------------ 1.800V ------- : [2.00v]
DRAM Termination -------- 0.900V ------- : [0.910v]
Channel A Reference ----- 0.900V ------- : [0.910v]
Channel B Reference ----- 0.900V ------- : [0.910v]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function ---------------------- : [Enabled]
Virtualization Technology -------------- : [Disabled]
and heres a screenshot with EIST Disabled, sorry bout that.
Comment