Re: Problem overclock Q6600 + EP45-DS3l
OK, thanks!
You never answered my questions...
You may need to look into testing changes to your MCH Ref/Vtt
See if this helps you any >>
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
CPU Frequency ...........................: 3600
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400 Mhz << Use 399 or 401
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800 mV
PCI Express Clock Drive.................: 800 mV
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00D << Have you tried 2.00B, just wondered as this sometimes is better depending on the memory
Memory Frequency (Mhz) ..............: 800 800
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................12
Advanced Timing Control - ALL AuTO
tRRD........................................... << Set 4 for now
tWTR.......................................... << Set 6 for now
tWR............................................ << Set 10 for now
tRFC........................................... << Set 72 for now
tRTP........................................... << Set 4 for now
Command Rate (CMD) ....................:2 << Set 2 manually, just in case
MISSING Settings, please set
Driving Strength Profiles
Driving Strength ............................ << Set 1066 for now
Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Set 9 for now
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Set 9 for now
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
CPU
CPU Vcore….……….........................:1.475
CPU Termination…..... 1.200V*.......:1.300
CPU PLL…………………....1.500V*.......: 1.550
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………,,0.800V*.......:Auto
MCH/ICH
MCH Core…………….....1.100V...........: 1.34 << Try less, maybe 1.24-1.28
MCH Reference….…….0.760V...........; Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.500V............: Auto
ICH Core…………...……1.100V............: Auto << Set 1.14
DRAM
DRAM Voltage ……....1.800V............: 2.000
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Enabled] <<< DISABLED
C2/C2E State Support....................: [Enabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Enabled] I', using vmware
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled]
OK, thanks!
You never answered my questions...
You may need to look into testing changes to your MCH Ref/Vtt
See if this helps you any >>
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
CPU Frequency ...........................: 3600
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400 Mhz << Use 399 or 401
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800 mV
PCI Express Clock Drive.................: 800 mV
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00D << Have you tried 2.00B, just wondered as this sometimes is better depending on the memory
Memory Frequency (Mhz) ..............: 800 800
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................12
Advanced Timing Control - ALL AuTO
tRRD........................................... << Set 4 for now
tWTR.......................................... << Set 6 for now
tWR............................................ << Set 10 for now
tRFC........................................... << Set 72 for now
tRTP........................................... << Set 4 for now
Command Rate (CMD) ....................:2 << Set 2 manually, just in case
MISSING Settings, please set
Driving Strength Profiles
Driving Strength ............................ << Set 1066 for now
Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Set 9 for now
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Set 9 for now
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
CPU
CPU Vcore….……….........................:1.475
CPU Termination…..... 1.200V*.......:1.300
CPU PLL…………………....1.500V*.......: 1.550
CPU Referen.…………....0.755V*.......: Auto
CPU Reference2………,,0.800V*.......:Auto
MCH/ICH
MCH Core…………….....1.100V...........: 1.34 << Try less, maybe 1.24-1.28
MCH Reference….…….0.760V...........; Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.500V............: Auto
ICH Core…………...……1.100V............: Auto << Set 1.14
DRAM
DRAM Voltage ……....1.800V............: 2.000
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Enabled] <<< DISABLED
C2/C2E State Support....................: [Enabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Enabled] I', using vmware
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled]
Comment