<br>
<br>
Hello..
I just upgrade from atholon xp..
Overclocking and setting was a breeze wht ep43-ud3l. ( the first board i tried. but northbridge was hot and i wanted a raid so i got ep45)
I can't get to 2 X 2 gig working on my board..
it works great with one stick. i lover clocked to 4.0ghz.
My wishes:
get the dual channel working
over clock 3.7+ stable.
++++++++++++++++++++++++++++++++++++++++++++++++
I hope i did this right... Couldn't run ET6 on Windows 7.. tried compabitly mode.. too
i tired bumping mch to 1.3... no go..
++++++++++++++++++++++++++++++++++++++++++++++++
Motherboard: GIGABYTE EP45-UD3P rev 1.6 bios FB
<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>
Cpu: Intel e5200
<o:p></o:p>
Ram: Crucial Ballistix 800 ddr2 4-4-4-12 2.0v<o:p></o:p>
Power Supply Unit: Coolmax 700W 700B
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [12 x]
Fine CPU Clock Ratio ----------------- : [+ 0.5] <-- ignore if not available
CPU Frequency ---------------------: 4.00 ( 320 X 12.5)<-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [320]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [800]
PCI Express Clock Drive -------------- : [900]
CPU Clock Skew (ps) ------------------ : [0]
MCH Clock Skew (ps) ------------------ : [0]
DRAM Performance Control
Performance Enhance ------------------- : [STD] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [3.20B] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [1024]
DRAM Timing Selectable ---------------- : [MANUAL] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- 5 ---------- : [5]
tRCD ------------------- 5---------- : [5]
tRP --------------------- 5 ---------- : [5]
tRAS ------------------- 18 ---------- : [15]
Advanced Timing Control
tRRD ------------------- 3 ---------- : [Auto]
tWTR ------------------- 3 ---------- : [Auto]
tWR --------------------- 6 ---------- : [Auto]
tRFC ------------------- 52---------- : [Auto]
tRTP ------------------- 3 ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- 1.27500 ---- : 1.40
CPU Termination --------- 1.2V* ----- : 1.2
CPU PLL ----------------- 1.5V* ----- : 1.5
CPU Reference ----------- 0.76V* ----- : [Auto]
CPU Reference2 ---------- NA
MCH/ICH
MCH Core ---------------- 1.1V ------- : 1.2
MCH Reference ----------- .76V ------- : [Auto]
MCH/DRAM Ref ------------ .900V ------ : [Auto]
ICH I/O ----------------- 1.5V ------- : 1.5
ICH Core ---------------- 1.1V ------- : 1.1
DRAM
DRAM Voltage ------------ 1.8V ------- : 2.2
DRAM Termination -------- .900V ------- : [Auto]
Channel A Reference ----- .900V ------- : [Auto]
Channel B Reference ----- .900V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]<o:p></o:p>
Comment