Overclocking the Gigabyte X58 UD4P

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

Those aren't high voltages at all, it just shows you need a better cooler is all, or you do not have it fully installed (Loose or too much paste)

I just though you might be able to lower voltages and temps a little,you want a top quality cooler like the. Prolimatech megahalems or the true 120,and two fans in push/pull,I use two fans on my cooler,you want to use top quality thermal paste like mx and tx 2 or 3,it will all help to lower CPU temps

The thermal paste I have is the Tuniq TX2 which is not bad I think it is among one of the best as I said
Now it's true I have only installed a fan on the cooler so it would have that tomorrow or tonight you esoty installing another fan to the famous push / pull
Another thing I have not always had high temperatures that I have to consider factors such as temperature against ambient summer now in round 20 at 25c and above all in the room that is the pc is very hot so no air power is part of the pc is stuck in a wooden desk
Mmmm otherwise thermal paste and apply it 2 years ago do not know if has something to do
Well what I describe is what I have right now on the pc
And what I do is change the fans that I came from stock in the case for a best to help remove hot air and the extra fan for the cooler unless you have another idea to help me I hope your answers

[wazza300]

Re: Overclocking the Gigabyte X58 UD4P

Yes summer temperatures will affect things,tx doesn't need any cure time so it should be fine,you can leave a window slightly open I find it helps in summer and leave side panel off on really hot days,noctua make powerful silent fans and scythe but you might need fan controller with the scythe as they can be loud

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

Yes summer temperatures will affect things,tx doesn't need any cure time so it should be fine,you can leave a window slightly open I find it helps in summer and leave side panel off on really hot days,noctua make powerful silent fans and scythe but you might need fan controller with the scythe as they can be loud

I forgot to mention that I have installed on the pc the NZXT Sentry 2, which controls all of the pc fans I have it 100%

[Lsdmeasap]

Re: Overclocking the Gigabyte X58 UD4P

Please do not put flash codes in your replies, thanks :)

TX-2 is good paste, I refer it over all others!

I just think you need a larger cooler for your system, especially since it's warmer where you live.

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

if good was thinking about buying a new one as the Tuniq TX4
For now not within my plans to buy a new cooler fans perhaps best buy for the cooler and the case
now I've put a fan over the cooler fan to be dual check the temperature and if you really like about 5 degrees down

[Lsdmeasap]

Re: Overclocking the Gigabyte X58 UD4P

I think TX-3 and MX-3 are WAY too thick, haven't tried TX-4

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

I rather do the oc intenet but in small amounts until you purchase a new thermal paste as the Tuniq TX4 and I have a small doubt about voltages for the oc to 3.0 ghz and so on for the vcore as not to start

Escuchar

[Lsdmeasap]

Re: Overclocking the Gigabyte X58 UD4P

What did I say about flash codes? Why do you keep putting them in your posts? If it's by accident some how that is fine, but please explain if so. If not, then stop it :)

< / OBJECT id=tts_flash codeBase=http://download.macromedia.com/pub/shockwave/cabs/flash/swflash.cab#version=5,0,0,0 height=18 width=18 classid=clsid:D27CDB6E-AE6D-11cf-96B8-444553540000 > < / OBJECT / >

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

If by accident sorry was something else and put it there by mistake
My only question is with which voltages for 3.0 and start going up and testing so far as it can reach temperatures kill me
Another thing seeing maybe a possible replacement to my cooler
what is the opinon for corsair h50?

[bacon612]

Re: Overclocking the Gigabyte X58 UD4P

I have applied your settings below last night and have begun stress testing to see if im stable now. Thanks for your suggestions and Ill report back soon.

Yeap, 124 BSOD is QPI/Vtt, often too low.

Try these and see how you get along.

Note my mention of Fail Safe, you are using that so it's probably part of your issues.

Advanced CPU Features:
CPU Clock Ratio ................................ [20x]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Auto]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Disabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... (x17)  x16-18
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 190
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[700mV]  << You are using Fail Safe, please load optimized defaults, and save/apply/reboot BACK TO THE BIOS.   Once in the BIOS set your SATA/Disk settings again, then come set all the overclock settings you need.

PCI Express Clock Drive ................... [700mV]  << You are using Fail Safe, please load optimized defaults, and save/apply/reboot BACK TO THE BIOS.   Once in the BIOS set your SATA/Disk settings again, then come set all the overclock settings you need.
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard]  << Extreme may be best
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [8]
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................8
tRCD .......................................8
tRP .........................................8
tRAS .......................................24



##Channel A Advanced Timing Control##
tRC ........................................ 27 Auto(Should be = tRAS + tRP or above for stability)
tRRD .......................................4 Auto
tWTR ...................................... 4 Auto(Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................8 Auto
tWTP ....................................... 19 Auto (tWTP Must = tWR + tWL + 4)
tWL ........................................ 7 Auto (tWL Must be CAS Latency -1)
tRFC ....................................... 60 Auto
tRTP ....................................... 4 Auto
tFAW ...................................... 16 Auto
Command Rate (CMD) ................ 1

##Channel A Misc Timing Control##
Round Trip Latency ................... 60 Auto

B2B CAS Delay .......................... - Auto


Advanced Voltage Control:

CPU
Load Line Calibration ................. [Enabled]
CPU Vcore ............................... 1.425
QPI/VTT Voltage 1.150v ............ 1.5 (have tried 1.36 to 1.5)  Ideal would be 1.25-1.45
CPU PLL 1.800v .......................1.880

MCH/ICH
PCIE 1.500v ........................... Auto
QPI PLL 1.100v ....................... 1.360  << 1.2 should be ok
IOH Core 1.100v ..................... 1.260
ICH I/O 1.500v ....................... Auto
ICH Core 1.1v ........................ 1.280  << 1.14-1.2 should be plenty

DRAM
DRAM Voltage 1.500v .............. 1.660
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

Finally I decided to buy another corsair cooler the h50 and the thermal paste tx-4 temperatures are greatly improved by at least 10 degrees still have not done OC and try to reach 4hgz I would like to know any help I can get trying make a stable and getting it to 4.0 ghz

[Lsdmeasap]

Re: Overclocking the Gigabyte X58 UD4P

This should work for you for 4Ghz

CPU Advanced Features:
CPU Clock Ratio ................................ [19x]
Intel (R) Turbo Boost Tech .................. [Enabled]
Enabled CPU Cores ............................ [All]
Multi Threading CPU .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
State C3/C6/C7 Support .................... [Disabled]
CPU Thermal Monitor.........................[Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled]
Bi-Directional PROCHOT ..................... [Enabled]

QPI Uncore & Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... X16
Frequency Isonchronous ..................[ Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 210
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive.............................[800MV]
PCI Express Clock Drive ................... [900MV]
CPU Clock Skew ............................. [0ps]
Clock Skew IOH ............................. [0ps]


DRAM Advanced Features:
Enhance Performance ...................... [Standard]  << Extreme
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [8.0]
DRAM Timing Selectable (SPD) .......... [Expert]

Channel A + B + C

Channel A Timing Settings:
Channel A # # # # Standard Timing Control
CAS Latency Time ...................... 8
tRCD ....................................... 8
tRP ......................................... 8
tRAS ....................................... 24

##Channel A Advanced Timing Control##
tRC ........................................Auto
tRRD .......................................Auto
tWTR ...................................... Auto
tWR ........................................Auto
tWTP .......................................Auto
tWL ........................................Auto
tRFC .......................................80
tRTP .......................................Auto
tFAW ......................................Auto
Command Rate (CMD) ................1

Channel A # # # # Misc Timing Control
Round Trip Latency ................... Auto


Advanced Voltage Control:

CPU
Load Line Calibration ................. [Enabled]
CPU Vcore ...............................1.350v-1.44
QPI/VTT Voltage 1.150v ............1.3-1.425
CPU PLL 1.800v .......................Auto

MCH/ICH
PCIE 1.500v ...........................Auto
QPI PLL 1.100v ....................... 1.2
IOH Core 1.100v ..................... 1.14-1.2
ICH I/O 1.500v .......................Auto
ICH Core 1.1v ........................Auto

DRAM
DRAM Voltage 1.500v..............1.66
0.750v DRAM Termination [Auto]
Ch-A Data Vref. 0.750v [AUTO]
Ch-B Data Vref. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address Vref. 0.750v [AUTO]
Ch-B Address Vref. 0.750v [AUTO]
Address VRef Ch-C. 0.750v [AUTO]

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

thanks i tried in the night

[Lsdmeasap]

Re: Overclocking the Gigabyte X58 UD4P

Cool, good luck tweaking and let us know how things work out for ya!

[k@non]

Re: Overclocking the Gigabyte X58 UD4P

try to do as I say above, but I had two problems
I first came the classic error 124 and then increase the vcore I just hung the pc bios entry