Configuration for GA-EP45-DS3P

[Lsdmeasap]

Re: Configuration for GA-EP45-DS3P

Yes, I already gave you that setting back with the full settings. That is your CPU's default setting anyway

So you need this >>>
>>> Standard Clock Control
CPU Host Clock Control Disabled
CPU Host Frequency (Mhz) 333
PCI Express Frequency (Mhz) 100
CIA2 Disabled
System Memory Multiplier (SPD)____ [2.40B] (FSB of CPU is 333 x 2.40B = 800Mhz ram speed)
DRAM Timing Selectable_______ SPD __ [Manual]

Your English is fine, I just thought maybe you were not listening to me or thought I was wrong.

[DjGonk]

Re: Configuration for GA-EP45-DS3P

So i change my bios configuration. Now it's ok, i wait some hours and days to see if it's ok.

I have a question : when i changed my bios configuration my pc reboot, it's possible this is due to a bad memory?

[Psycho101]

Re: Configuration for GA-EP45-DS3P

when i changed my bios configuration my pc reboot, it's possible this is due to a bad memory?

No this is normal. If a setting you changed requires the motherboard to re-set internal settings to accomodate the change, it will totally power off the system before re-starting again.

[DjGonk]

Re: Configuration for GA-EP45-DS3P

But the system not restarted, i restarted my computer with the button reset. I did not even validate my input (F10). I think May be that you said : th e motherboard want to reboot after changed an option.

[Lsdmeasap]

Re: Configuration for GA-EP45-DS3P

You need to use F10 to apply your changes, then the system will restart, sometimes 2-3 times before the settings are applied and windows will boot. Depends on what you change or how many changes you make

[DjGonk]

Re: Configuration for GA-EP45-DS3P

So. I still had some Bosd but I like the RC windows seven, I don't know what to think about this.

Moreover some times when starting the BIOS, he block on the detection of memory. I'm going into the BIOS, and then I got a warning message telling me that I had a bios crash to overclock.

So i changed some voltage : Auto to Normal.

If you have some ideas. Thx.

[Chike]

Re: Configuration for GA-EP45-DS3P

Could you post your current BIOS settings?
Have you ran memtest86+ with only one stick in slot 3 too?

[DjGonk]

Re: Configuration for GA-EP45-DS3P

Hi,

Now my Bios blocked many many times at the first sreen on "Detecting Memory" (bottom of the logo of Bios Award). I think tomorrow i will change my memory.

My Bios is :

Thanks!

Here would be default settings for your hardware

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.00


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................4
tRCD .........................................4
tRP'...........................................4
tRAS..........................................12

Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3
tWR............................................ 4
tRFC........................................... 52
tRTP........................................... 3
Command Rate (CMD) ....................:2

Channel A
Static tRead Value.........................:6/7-10 333/B MCH
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:6/7-10 333/B MCH
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto

Motherboard Voltage Control

CPU
CPU Vcore….……….........................:Auto
CPU Termination…..... 1.200V*.......: << 1.200V
CPU PLL…………………....1.500V*.......: << 1.500V
CPU Referen.…………....0.755V*.......: <<< 0.755V
CPU Reference2………,,0.800V*.......:<<< 0.800V

MCH/ICH
MCH Core…………….....1.100V...........: << 1.100V
MCH Reference….…….0.800V...........; <<< 0.800V
MCH/DRAM Ref.…......0.900V...........: <<< 0.900V
ICH I/O……………….....1.500V............: <<< 1.500V
ICH Core…………...……1.100V............: <<< 1.100V

DRAM
DRAM Voltage ……....1.800V............: 2.1V
DRAM Termination .…0.900V............: 0.900V
Channel A Reference 0.900V............: 0.900V
Channel B Reference 0.900V............: 0.900V

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]<< you can leave enabled if you do not want to overclock
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled] << you can leave enabled if you do not want to overclock
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from</pre>

[Chike]

Re: Configuration for GA-EP45-DS3P

It could be much easier to assist you if you had your system specs in your signature,
IMO you don't need most the settings changes you made in BIOS where the assential settings MCH Core left auto.
I reccomend you to clear BIOS, the load optimized defaults, Set Performance Enhance to standard, all other settings on auto, and see if incerasing MCH Core, one notch at a time, up to 1.26v make things better.
If increasing MCH Core doesn't help try lowering down from 1.1v, again one notch at a time, down to 0.95v,

[DjGonk]

Re: Configuration for GA-EP45-DS3P

Thank's for your reply. I make my signature, but i write my system specs on the first post.

For the Bios i changed auto to the value for voltage, because my bios got a warning message telling me that I had a bios crash to overclock.

But i'm trying now with your proposition.

[DjGonk]

Re: Configuration for GA-EP45-DS3P

Ok so i changed my bios, and now it's that :

My Bios is :

Thanks!

Here would be default settings for your hardware

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.00


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................4
tRCD .........................................4
tRP'...........................................4
tRAS..........................................12

Advanced Timing Control
tRRD........................................... Auto
tWTR.......................................... Auto
tWR............................................ Auto
tRFC........................................... Auto
tRTP........................................... Auto
Command Rate (CMD) ....................:Auto

Channel A
Static tRead Value.........................:7
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto

Driving Strenght Profiles
Driving Strenght ...........................: 800Mhz

Motherboard Voltage Control

CPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]


It's good for you?

[Chike]

Re: Configuration for GA-EP45-DS3P

Settings look ok, do you still get the red warning?
It's not if it's good for me but if they are stable and work for you, you the only one to say if they are good or not.
Run memtest86+ first then see if you get more BSODs.
To be sure everything is 99.9% stable you'll need to run some kind of stress test like Prime95 blend test for 6+ hours,

[DjGonk]

Re: Configuration for GA-EP45-DS3P

The red warning disappear and i see this warning just one time.
For the value may be it's good for me, you have right when you said that : "It's not if it's good for me but if they are stable and work for you, you the only one to say if they are good or not". But I don't want necessarily overcloker the computer but it only works well at first. However in the futur if the system is stable may be ...

For memtest86+ my memory pass 14 times without erros. I will try Prime95 blend test this night and i post the result of this test tomorow.

Thx a lot Chike. And good night (may be just for me because in France it's night )

[Chike]

Re: Configuration for GA-EP45-DS3P

If sticker on the memory says it can have 2.1v, and Prime95 fail, set DRAM Voltage 2.05-2.1v, try again.
If this does not help try 1.26v MCH Core.

[DjGonk]

Re: Configuration for GA-EP45-DS3P

Hi Chike.

Prime95 has turned all night without error. Now i can't try another test but tonigth may be i can try some test if you want (may be another software for testing memory and system).