OK, finally am ready to tag someone else in :)
I have tried every config found on this board as a starting point. (From Grishka's E8400 builds to D-an-W's huge discussion thread)
My goal is to get above 4ghz for daily (gaming) usage. 4.04 would be fine.
My current stable settings Overclocked at 3.6:
D-an-W's initial posted settings were the first I could use to get into Windows, but I had to set all of my memory settings to AUTO to get there. It was NOT stable running Orthos for longer than 5 seconds :)
I am just not sure where to go... HELP!
I have tried every config found on this board as a starting point. (From Grishka's E8400 builds to D-an-W's huge discussion thread)
My goal is to get above 4ghz for daily (gaming) usage. 4.04 would be fine.
My current stable settings Overclocked at 3.6:
Code:
Motherboard: Model: EP45-UD3P Rev#: 1.1 Bios Version: F9 Cpu: Intel E8400 C0 step Ram: Dominator Series Twin2X2048-8500C5D (http://www.corsair.com/_datasheets/TWIN2X2048-8500C5D.pdf) Power Supply Unit: Thermaltake 750w MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster -------------- : Fast CPU Clock Ratio ---------------------- : 9x Fine CPU Clock Ratio ----------------- : 0 CPU Frequency ---------------------: 3.600 Clock Chip Control Standard Clock Control CPU Host Clock Control --------------- : [Enabled] CPU Host Frequency (Mhz) --------------: [400] PCI Express Frequency (Mhz) ---------- : [100] C.I.A.2 ------------------------------ : [Disabled] Advanced Clock Control ------- [Press Enter] CPU Clock Drive ---------------------- : Auto PCI Express Clock Drive -------------- : Auto CPU Clock Skew (ps) ------------------ : Auto MCH Clock Skew (ps) ------------------ : Auto DRAM Performance Control Performance Enhance ------------------- : [Disabled] Extreme Memory Profile --- (X.M.P.) --- : [Disabled] (G)MCH Frequency Latch ---------------- : [Auto] System Memory Multiplier -------------- : [2.66d] Memory Frequency (Mhz) ---------------- : [1066] DRAM Timing Selectable ---------------- : [Manual] Standard Timing Control CAS Latency Time -------- ?? ---------- : [5] tRCD ------------------- ?? ---------- : [5] tRP --------------------- ?? ---------- : [5] tRAS ------------------- ?? ---------- : [15] Advanced Timing Control tRRD ------------------- ?? ---------- : [Auto] tWTR ------------------- ?? ---------- : [Auto] tWR --------------------- ?? ---------- : [Auto] tRFC ------------------- ?? ---------- : [Auto] tRTP ------------------- ?? ---------- : [Auto] Command Rate (CMD) -------------------- : [Auto] Channel A Static tRead Value --------------------- : [Auto] tRD Phase0 Adjustment ------------------ : [Auto] tRD Phase1 Adjustment ------------------ : [Auto] tRD Phase2 Adjustment ------------------ : [Auto] tRD Phase3 Adjustment ------------------ : [Auto] Trd2rd(Different Rank) ----------------- : [Auto] Twr2wr(Different Rank) ----------------- : [Auto] Twr2rd(Different Rank) ----------------- : [Auto] Trd2wr(Same/Diff Rank) ----------------- : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] ps Dimm2 Clock Skew Control --------------- : [Auto] ps Channel B Static tRead Value --------------------- : [Auto] tRD Phase0 Adjustment ------------------ : [Auto] tRD Phase1 Adjustment ------------------ : [Auto] tRD Phase2 Adjustment ------------------ : [Auto] tRD Phase3 Adjustment ------------------ : [Auto] Trd2rd(Different Rank) ----------------- : [Auto] Twr2wr(Different Rank) ----------------- : [Auto] Twr2rd(Different Rank) ----------------- : [Auto] Trd2wr(Same/Diff Rank) ----------------- : [Auto] Dimm1 Clock Skew Control --------------- : [Auto] ps Dimm2 Clock Skew Control --------------- : [Auto] ps Motherboard Voltage Control CPU Voltage Types------------ Normal -------- Current ----- Load-Line Calibration ----------------- : [Enables] CPU Vcore --------------- 1.????? ---- : [1.306] CPU Termination --------- 1.200V* ----- : [Auto] CPU PLL ----------------- 1.500V* ----- : [Auto] CPU Reference ----------- 0.755V* ----- : [Auto] CPU Reference2 ---------- 0.800V* ----- : [Auto] MCH/ICH MCH Core ---------------- 1.100V ------- : [1.2] MCH Reference ----------- 0.800V ------- : [Auto] MCH/DRAM Ref ------------ 0.900V ------ : [Auto] ICH I/O ----------------- 1.500V ------- : [Auto] ICH Core ---------------- 1.100V ------- : [Auto] DRAM DRAM Voltage ------------ 1.800V ------- : [2.100] DRAM Termination -------- 0.900V ------- : [Auto] Channel A Reference ----- 0.900V ------- : [Auto] Channel B Reference ----- 0.900V ------- : [Auto] Advanced Settings Limit CPUID Max. to 3 ------------------ : [Disabled] No-Execute Memory Protect -------------- : [Enabled] CPU Enhanced Halt (C1E) ---------------- : [Disabled] C2/C2E State Support ------------------- : [Disabled] x C4/C4E State Support ----------------- : [Disabled] CPU Thermal Monitor 2 (TM2) ------------ : [Enabled] CPU EIST Function --------------------- : [Disabled] Virtualization Technology -------------- : [Disabled] Integrated Peripherals Legacy USB Storage Detect ------------- : [Disabled]
D-an-W's initial posted settings were the first I could use to get into Windows, but I had to set all of my memory settings to AUTO to get there. It was NOT stable running Orthos for longer than 5 seconds :)
I am just not sure where to go... HELP!
Comment