q6600 3.6ghz ep 45dsl help

[wutsup]

Re: q6600 3.6ghz ep 45dsl help

my board doesn't have that the problem with the ep45 ds3l is the big vdroop

at idle in windows its 1.44 with the above settings and under load it goes all the way to 1.396

[Psycho101]

Re: q6600 3.6ghz ep 45dsl help

It's still worth trying. You don't know if you don't try and it will do no harm.

And you defiantly need to lower CPU termination to 1.4-1.42 IMO. VTT is important in its own right but it must also be slightly lower than Vcore. I would lower this without even trying LLC. You may even be ok at 1.38V. More is not always better.

[Lsdmeasap]

Re: q6600 3.6ghz ep 45dsl help

If you are trying to load 3.6Ghz on a Q6600 you may need more Vtt actually, maybe 1.45-1.5

[wutsup]

Re: q6600 3.6ghz ep 45dsl help

hey LSD ive been waiting for a reply from you lol. is that safe for the cpu in the long run?

and what settings do you suggest i try for 3.6(reead previous posts for what ive tried)
thanks man

[Lsdmeasap]

Re: q6600 3.6ghz ep 45dsl help

Well that all depends on your temps, but yes 65NM Cpu's need and can handle far more Vtt than 45NM ones can. If your temps are good the CPU will outlast your desire to own it really.

3.6 is pretty tough on a Q6600 not all will do it for sure. Please post for me the furthest stable settings you have as of now and I will try to see if I can advise you back somethings to try

[wutsup]

Re: q6600 3.6ghz ep 45dsl help

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [##] 9
Fine CPU Clock Ratio ----------------- : [0.0] < ignore if not available
CPU Frequency ---------------------: #### 3.60ghz (400x9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [Mhz] 400
PCI Express Frequency (Mhz) ---------- : [Auto] <--- 100
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : <<< 800
PCI Express Clock Drive -------------- : <<< 800
CPU Clock Skew (ps) ------------------ : <<< 0
MCH Clock Skew (ps) ------------------ : <<< 0
DRAM Performance Control
Performance Enhance ------------------- : [Turbo] <--- set to DISABLED when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto] 400
System Memory Multiplier -------------- : [Auto] 2.66d
Memory Frequency (Mhz) ---------------- : [Auto] 1066
DRAM Timing Selectable ---------------- : [Auto] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [Auto] 5
tRCD ------------------- ?? ---------- : [Auto] 6
tRP --------------------- ?? ---------- : [Auto] 6
tRAS ------------------- ?? ---------- : [Auto] 18
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : 55
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value ----------- ?? ------ : [Auto] 7
tRD Phase0 Adjustment -------- ?? ------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment -------- ?? ------ : [Auto]
tRD Phase2 Adjustment -------- ?? ------ : [Auto]
tRD Phase3 Adjustment -------- ?? ------ : [Auto]
Trd2rd(Different Rank) ------- ?? ------ : [Auto]
Twr2wr(Different Rank) ------- ?? ------ : [Auto]
Twr2rd(Different Rank) ------- ?? ------ : [Auto]
Trd2wr(Same/Diff Rank) ------- ?? ------ : [Auto]
Dimm1 Clock Skew Control ----- ?? ------ : [Auto] ps
Dimm2 Clock Skew Control ----- ?? ------ : [Auto] ps
Channel B
Static tRead Value ----------- ?? ------ : [Auto] 7
tRD Phase0 Adjustment -------- ?? ------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment -------- ?? ------ : [Auto]
tRD Phase2 Adjustment -------- ?? ------ : [Auto]
tRD Phase3 Adjustment -------- ?? ------ : [Auto]
Trd2rd(Different Rank) ------- ?? ------ : [Auto]
Twr2wr(Different Rank) ------- ?? ------ : [Auto]
Twr2rd(Different Rank) ------- ?? ------ : [Auto]
Trd2wr(Same/Diff Rank) ------- ?? ------ : [Auto]
Dimm1 Clock Skew Control ----- ?? ------ : [Auto] ps
Dimm2 Clock Skew Control ----- ?? ------ : [Auto] ps
Motherboard Voltage Control
CPU
CPU Vcore --------------- 1.????? ---- : 1.493(just one notch under 1.5
CPU Termination --------- 1.200V* ----- : 1.44
CPU PLL ----------------- 1.500V* ----- : 1.55
cPU Reference ----------- 0.755V* ----- : [Auto] <--- Auto Will set this correctly
MCH/ICH
MCH Core ---------------- 1.100V ------- : 1.4
MCH Reference ----------- 0.800V ------- : [Auto]
ICH I/O ----------------- 1.500V ------- : [Auto]
DRAM
DRAM Voltage ------------ 1.800V ------- : 2.1(manufacturer settings)
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled] disabled
No-Execute Memory Protect -------------- : Enabled
CPU Enhanced Halt (C1E) ---------------- : [Disabled] disabled
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled] enabled
CPU EIST Function --------------------- : [Disabled] disabled
Virtualization Technology -------------- : [Disabled] disabled
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Enabled] disabled

[wutsup]

Re: q6600 3.6ghz ep 45dsl help

bump