Trouble with GA-EP43-DS3L

[righty]

Re: Trouble with GA-EP43-DS3L

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: 0.0
CPU Frequency ...........................: 3.60


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 3600 MHz (400 x 9)
PCI Express Frequency (Mhz) .........: Auto

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.66D

Memory Frequency (Mhz) ..............: 1066
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 6
tRP'........................................... 6
tRAS.......................................... 18

Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD........................................... 4
tWTR.......................................... 6
tWR............................................ 8
tRFC........................................... 62
tRTP........................................... 5
Command Rate (CMD) ....................: [0]

Driving Strength Profiles
Driving Strength ............................ 1066

Channel A
Static tRead Value.........................:12
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:12
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

About your voltages here for CPU, I did not advise because you said you have a stable 3.6 overclock, but I do want to ask you are not using Auto Vcore, Termination, And PLL are you?? I hope not as it will fry your CPU

MotherboardAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB <<< [Enabled]

I am sending the RAM back for a RMA. I won't have the RAM to test after tomorrow but will be getting my returned RAM hopefully by next week. I would still like to hear what you think is going on. I mean after I applied the settings you stated above my PC didn't even want to start. As of now I am using my trusty Kingston 800 MHz RAM. Let's just hope this RAM doesn't mess up on me .

[Lsdmeasap]

Re: Trouble with GA-EP43-DS3L

I suggested 399 or 401 FSB, not likely a huge issue, but just wanted to point that out as the first thing I noticed.

Did you try 1.05 MCH and less then 1.3 like 1.2-1.24 or so? 1.3 may have been to much

I also see you are using 1.25 vcore, that may need to be much more or at least more anyway. And I advised that you should not use Auto PLL and Termination but you are still, this will fry your CPU. You have to manually set those for sure.

Let us know when you get your new ram, if it is different, and we will try to help ya get going.