Is there an overclocking guide for the UD3P?

[Lsdmeasap]

Re: Is there an overclocking guide for the UD3P?

Please post for me the exact settings you are using so I can advise of maybe why you are having issues.

Ever use Acronis True Image? Works great and only take a few to mirror your system and then only a few minutes to mirror the drive back if your install fails

[Jsunn]

Re: Is there an overclocking guide for the UD3P?

Please post for me the exact settings you are using so I can advise of maybe why you are having issues.

Ever use Acronis True Image? Works great and only take a few to mirror your system and then only a few minutes to mirror the drive back if your install fails

I will post them this evening as I am at work now. I reinstalled

I tried to use the windows complete system backup that comes with vista. When I booted from the CD, it couldn't see my RAID array?? I even tried to load the RAID drivers from my USB thumb drive. It would say that it was loading drivers and then give an error that the "install was not successful".

I will need to be more careful.

Thanks for your help.

-Jason

[Jsunn]

Re: Is there an overclocking guide for the UD3P?

The following settings give me a BSOD before entering Windows:

I am using BIOS F7c

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: FAST 			
CPU Clock Ratio .......................: 9			
Fine CPU Clock Ratio...................: 0.5			
CPU Frequency .........................: 3.80GHz (400X9.5)

Clock Chip Control 
Standard Clock Control
CPU Host Clock Control.................: [Enabled] 		
CPU Host Frequency (Mhz) ..............: 400			
PCI Express Frequency (Mhz) ...........: 100			
C.I.A.2 ...............................: [Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 800mV 
PCI Express Clock Drive................: 900mV 
CPU Clock Skew (ps)....................: 0ps 
MCH Clock Skew (ps)....................: 0ps 


DRAM Performance Control
Performance Enhance....................: [STANDARD]		
Extreme Memory Profile (X.M.P.)........: [Disabled]		
(G)MCH Frequency Latch.................: [AUTO]
System Memory Multiplier ..............: 2.66D			
Memory Frequency (Mhz) ................: 1066		
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15

Advanced Timing Control
tRRD...................................: 4
tWTR...................................: 4
tWR....................................: 5 
tRFC...................................: 62 
tRTP...................................: 4
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ......................: 1066

Channel A
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO] 
Twr2wr(Different Rank).................: 8 [AUTO] 
Twr2rd(Different Rank).................: 7 [AUTO] 
Trd2wr(Same/Diff Rank).................: 9 [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]

Channel B
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO] 
Twr2wr(Different Rank).................: 8 [AUTO] 
Twr2rd(Different Rank).................: 7 [AUTO] 
Trd2wr(Same/Diff Rank).................: 9 [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]


Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Disabled]		
CPU Vcore..............................: 1.250v 		
CPU Termination........................: 1.240V 		
CPU PLL................................: 1.570V 	
CPU Reference..........................: 0.760V [AUTO] 		


MCH/ICH
MCH Core...............................: 1.240V 		
MCH Reference..........................: 0.760v [AUTO]		
MCH/DRAM Ref...........................: 0.900V [AUTO]		
ICH I/O................................: 1.570V 		
ICH Core...............................: 1.200V 		

DRAM
DRAM Voltage...........................: 1.9v 	
DRAM Termination ......................: 0.900V [AUTO]		
Channel A Reference....................: 0.900V [AUTO]		
Channel B Reference ...................: 0.900V [AUTO]		

Advanced Settings
Limit CPUID Max. to 3..................: [Disabled]
No-Execute Memory Protect..............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support...................: [Disabled]
x C4/C4E State Support.................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Disabled]
CPU EIST Function......................: [Disabled]
Virtualization Technology..............: [Disabled] 

Integrated Peripherals
Legacy USB Storage Detect .............:[Enabled]

[Jsunn]

Re: Is there an overclocking guide for the UD3P?

Now, if I just change the the FSB to 400 and manualy enter my RAM timings and keep everything else on auto. I can boot into Windows.

What do you think?

There are so many variables.

-Jason

[Jsunn]

Re: Is there an overclocking guide for the UD3P?

Anyone?