ep45-ud3p few questions

[nafroman]

Re: ep45-ud3p few questions

(LLC) not safe.. meaning i should disable it ?


and those are my current settings ... who passed all tests except prime95 failing after 7 hours..

******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 3.8GHz............................[ 475 x 8.0 ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 475 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]

******DRAM Performance Control******

Performance Enhance.............................[Standard]
(G) MCH Frequency Latch.........................[ AUTO]
System Memory Multiplier.........................[ 2.00D]
Memory Frequency 800............................[ 950]
DRAM Timing Selectable..........................[ Manual]

CAS Latency Time................................[ 5]
tRCD............................................[ 5]
tRP.............................................[ 5]
tRAS............................................[ 15 ]

******Advanced Timing Control******

tRRD............................................[ 4 ]
tWTR............................................[ 4 ]
tWR.............................................[ 5 ]
tRFC............................................[ 55 ]
tRTP............................................[ 4 ]
Command Rate (cmd)..............................[ 2 ]

******Channel A Timing Settings******

Static tRead Value  ...............[ 9 ]
tRD Phase0 Adjustment ................[ Auto ]
tRD Phase1 Adjustment  ................[ Auto ]
tRD Phase2 Adjustment  ................[ Auto ]
tRD Phase3 Adjustment  ................[ Auto ]

tRD 2rd (Different Rank)  ................[ Auto ]
tWR 2wr (Different Rank)  ................[ Auto ]
tWR 2rd (Different Rank)  ................[ Auto ]
tRD 2wr (Same/Difft Rank) ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******

Drive Strength Profile..........................[ 800MHZ ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******

Static tRead Value  ...............[ 9 ]
tRD Phase0 Adjustment  ................[ Auto ]
tRD Phase1 Adjustment  ................[ Auto ]
tRD Phase2 Adjustment  ................[ Auto ]
tRD Phase3 Adjustment  ................[ Auto ]

tRD 2rd (Different Rank)  ................[ Auto ]
tWR 2wr (Different Rank)  ................[ Auto ]
tWR 2rd (Different Rank)  ................[ Auto ]
tRD 2wr (Same/Difft Rank)................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******

Drive Strength Profile..........................[800MHZ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.21250 ]...................[ 1.28125V ]
CPU Termination [ 1.20 ]...................[ 1.240V ]
CPU PLL [ 1.50 ]...................[ 1.590V ]
CPU Reference [ 0.760 ]...................[ 0.785V ]

MCH Core [ 1.100 ]...................[ 1.22V]
MCH Reference [ 0.760 ]...................[ 0.825V ]
MCH/DRAM Reference [ 0.900 ]...................[0.9V ]
ICH I/O [ 1.500 ]...................[ 1.57V ]
ICH Core [ 1.100 ]...................[ 1.2V]

DRAM Voltage [ 1.800 ]...................[ 2.1V]
DRAM Termination [ 0.900 ]...................[0.9V]
Channel A Ref [ 0.900 ]...................[ 0.9V]
Channel B Ref [ 0.900 ]...................[0.9V]

[nafroman]

Re: ep45-ud3p few questions

so what now ? i left this testing issue aside for a day ... now in this day with system on 3.8GHZ ... i manage to play heavy games .. like crysis , gta4 , cod5 and others... everything seems to be going o.k... no crashes or freezes... but still i guess when ill run prime95 it would freeze/crash the system after 7-8 hours... i beginning to think that the problem is not my O.C being unstable .. instead i think maybe it's my sound card device or driver... cause it sitting on PCI-E , so he might be trobuled by this O.C stuff..

is it possible ?
or it's not the problem ? in that case ...should i stay as is or try tweaking and running prime95 once again ?