Hey Guys,
This is a reference for those interested in overclocking a Q6600 B3 Stepping on a UD3R. CPU @ 3.0 ghz and ram ddr2 800 @ 1000mhz
This is a low/simple overclock. My 3.2 ghz boots but fails orthos. Too much work so I settled with 3.0. Any Ideas? Otherwise, use these references for your own overclocks if needed.
Below are my specs and bios settings.
Intel Q6600 @ 3.0 ghz
4 GB ddr2 800
(2x1 OCZ reapers rated at 4-4-4-15 1T 'OCZ2RPR8002GK' and 2x1 OCZ gaming ram 4-4-4-15 1T 'OCZ2N800SR2GK')
8800 GTX
Corsair 520HX
EP45-UD3R rev. A3
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9x
CPU Frequency ...........................: 3.0GHz (333x9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: auto
PCI Express Clock Drive.................: auto
CPU Clock Skew (ps)....................: auto
MCH Clock Skew (ps)...................: auto
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Auto
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: auto
Memory Frequency (Mhz) ..............: 1000
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time.......................5
tRCD .........................................5
tRP'...........................................5
tRAS.........................................15
Advanced Timing Control
tRRD...........................................aut o
tWTR..........................................auto
tWR............................................aut o
tRFC...........................................aut o
tRTP...........................................aut o
Command Rate (CMD) ....................2t
Driving Strength Profiles
Driving Strength ............................
Channel A
Static tRead Value.........................:Auto
tRD Phase0 Adjustment...................Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
Channel B
Static tRead Value.........................:Auto
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
Motherboard
This is a reference for those interested in overclocking a Q6600 B3 Stepping on a UD3R. CPU @ 3.0 ghz and ram ddr2 800 @ 1000mhz
This is a low/simple overclock. My 3.2 ghz boots but fails orthos. Too much work so I settled with 3.0. Any Ideas? Otherwise, use these references for your own overclocks if needed.
Below are my specs and bios settings.
Intel Q6600 @ 3.0 ghz
4 GB ddr2 800
(2x1 OCZ reapers rated at 4-4-4-15 1T 'OCZ2RPR8002GK' and 2x1 OCZ gaming ram 4-4-4-15 1T 'OCZ2N800SR2GK')
8800 GTX
Corsair 520HX
EP45-UD3R rev. A3
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9x
CPU Frequency ...........................: 3.0GHz (333x9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: auto
PCI Express Clock Drive.................: auto
CPU Clock Skew (ps)....................: auto
MCH Clock Skew (ps)...................: auto
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Auto
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: auto
Memory Frequency (Mhz) ..............: 1000
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time.......................5
tRCD .........................................5
tRP'...........................................5
tRAS.........................................15
Advanced Timing Control
tRRD...........................................aut o
tWTR..........................................auto
tWR............................................aut o
tRFC...........................................aut o
tRTP...........................................aut o
Command Rate (CMD) ....................2t
Driving Strength Profiles
Driving Strength ............................
Channel A
Static tRead Value.........................:Auto
tRD Phase0 Adjustment...................Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
Channel B
Static tRead Value.........................:Auto
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
Motherboard
Comment