Hi all,
I have the ep45-ds3 board and after I tried a million times the hyperx 8500 to make them work at 1066 I changed them with the xms2 8500 2x2gb but it seems that I have the same problem,please help me figure this out because its going to drive me crazy.
Here are my settings:
GIGABYTE GA-EP45_EXTREME
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster: AUTO
CPU Clock Ratio: 8x
Fine CPU Clock Ratio: [0.0]
CPU Frequency: 2.66Ghz(333x8)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control: [Disabled]
CPU Host Frequency(Mhz): 333 Mhz
PCI Express Frequency(Mhz): 100 Mhz
C.I.A. 2: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive: 800mv
PCI Express Clock Drive: 900mv
CPU Clock Skew: 0ps
MCH Clock Skew: 50ps
DRAM Performance Control
Performance Enhance: [Standard]
Extreme Memory Profile (X.M.P.): [Disabled]
(G)MCH Frequency Latch: [333]
System Memory Multiplier:3.20
Memory Frequency (Mhz):1066 Mhz
DRAM Timing Selectable: [Manual]
Standard Timing Control
CAS Latency Time: 5
tRCD: 5
tRP: 5
tRAS: 18 (I tried also 15)
Advanced Timing Control [Press Enter]
tRRD:6
tWTR:14
tWR:16
tRFC:75
tRTP:7
Command Rate (CMD):2
>>>>> Channel A
Channel A Timing Settings: [Press Enter]
Static tRead Value: 10 I've tried also 12 and 14
tRD Phase0 Adjustment: Auto
tRD Phase1 Adjustment: Auto
tRD Phase2 Adjustment: Auto
tRD Phase3 Adjustment: Auto
Trd2rd(Different Rank).: 8
Twr2wr(Different Rank): 8
Twr2rd(Different Rank): 7
Trd2wr(Same/Diff Rank): 9
Dimm1 Clock Skew Control: Auto
Dimm2 Clock Skew Control: Auto
DDR3 Write Training: Auto
Channel A Driving Settings: [Press Enter]
Driving Strength Profile: 1066Mhz I 've tried also oc-1200
Data Driving Pull-Up Level: AUTO
Cmd Driving Pull-Up Level: AUTO
Ctrl Driving Pull-Up Level: AUTO
Clk Driving Pull-Up Level: AUTO
Data Driving Pull-Down Level: AUTO
Cmd Driving Pull-Down Level: AUTO
Ctrl Driving Pull-Down Level: AUTO
Clk Driving Pull-Down Level: AUTO
>>>>> Channel B
Channel B Timing Settings: [Press Enter]
Static tRead Value: 10 I've tried also 12 and 14
tRD Phase0 Adjustment: Auto
tRD Phase1 Adjustment: Auto
tRD Phase2 Adjustment: Auto
tRD Phase3 Adjustment: Auto
Trd2rd(Different Rank).: 8
Twr2wr(Different Rank): 8
Twr2rd(Different Rank): 7
Trd2wr(Same/Diff Rank): 9
Dimm1 Clock Skew Control: Auto ps
Dimm2 Clock Skew Control: Auto ps
DDR3 Write Training: Auto
Channel B Driving Settings: [Press Enter]
Driving Strength Profile: 1066Mhz I 've tried also oc-1200
Data Driving Pull-Up Level: AUTO
Cmd Driving Pull-Up Level: AUTO
Ctrl Driving Pull-Up Level: AUTO
Clk Driving Pull-Up Level: AUTO
Data Driving Pull-Down Level: AUTO
Cmd Driving Pull-Down Level: AUTO
Ctrl Driving Pull-Down Level: AUTO
Clk Driving Pull-Down Level: AUTO
Motherboard Voltage Control
CPU Vcore: 1.25v
CPU Termination | 1.200V: v
CPU PLL | 1.500V: v
CPU Reference | 0.760V: v
MCH Core | 1.100V:1.26 v
MCH Reference | 0.900V: v
MCH/DRAM Ref | 0.900V: v
ICH I/O | 1.500V: v
DRAM Voltage | 1.800V:2.1 v
DRAM Termination | 0.900V: v
Channel A Reference | 0.900V: v
Channel B Reference | 0.900V: v
Thanks in advance
Nikos
I have the ep45-ds3 board and after I tried a million times the hyperx 8500 to make them work at 1066 I changed them with the xms2 8500 2x2gb but it seems that I have the same problem,please help me figure this out because its going to drive me crazy.
Here are my settings:
GIGABYTE GA-EP45_EXTREME
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster: AUTO
CPU Clock Ratio: 8x
Fine CPU Clock Ratio: [0.0]
CPU Frequency: 2.66Ghz(333x8)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control: [Disabled]
CPU Host Frequency(Mhz): 333 Mhz
PCI Express Frequency(Mhz): 100 Mhz
C.I.A. 2: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive: 800mv
PCI Express Clock Drive: 900mv
CPU Clock Skew: 0ps
MCH Clock Skew: 50ps
DRAM Performance Control
Performance Enhance: [Standard]
Extreme Memory Profile (X.M.P.): [Disabled]
(G)MCH Frequency Latch: [333]
System Memory Multiplier:3.20
Memory Frequency (Mhz):1066 Mhz
DRAM Timing Selectable: [Manual]
Standard Timing Control
CAS Latency Time: 5
tRCD: 5
tRP: 5
tRAS: 18 (I tried also 15)
Advanced Timing Control [Press Enter]
tRRD:6
tWTR:14
tWR:16
tRFC:75
tRTP:7
Command Rate (CMD):2
>>>>> Channel A
Channel A Timing Settings: [Press Enter]
Static tRead Value: 10 I've tried also 12 and 14
tRD Phase0 Adjustment: Auto
tRD Phase1 Adjustment: Auto
tRD Phase2 Adjustment: Auto
tRD Phase3 Adjustment: Auto
Trd2rd(Different Rank).: 8
Twr2wr(Different Rank): 8
Twr2rd(Different Rank): 7
Trd2wr(Same/Diff Rank): 9
Dimm1 Clock Skew Control: Auto
Dimm2 Clock Skew Control: Auto
DDR3 Write Training: Auto
Channel A Driving Settings: [Press Enter]
Driving Strength Profile: 1066Mhz I 've tried also oc-1200
Data Driving Pull-Up Level: AUTO
Cmd Driving Pull-Up Level: AUTO
Ctrl Driving Pull-Up Level: AUTO
Clk Driving Pull-Up Level: AUTO
Data Driving Pull-Down Level: AUTO
Cmd Driving Pull-Down Level: AUTO
Ctrl Driving Pull-Down Level: AUTO
Clk Driving Pull-Down Level: AUTO
>>>>> Channel B
Channel B Timing Settings: [Press Enter]
Static tRead Value: 10 I've tried also 12 and 14
tRD Phase0 Adjustment: Auto
tRD Phase1 Adjustment: Auto
tRD Phase2 Adjustment: Auto
tRD Phase3 Adjustment: Auto
Trd2rd(Different Rank).: 8
Twr2wr(Different Rank): 8
Twr2rd(Different Rank): 7
Trd2wr(Same/Diff Rank): 9
Dimm1 Clock Skew Control: Auto ps
Dimm2 Clock Skew Control: Auto ps
DDR3 Write Training: Auto
Channel B Driving Settings: [Press Enter]
Driving Strength Profile: 1066Mhz I 've tried also oc-1200
Data Driving Pull-Up Level: AUTO
Cmd Driving Pull-Up Level: AUTO
Ctrl Driving Pull-Up Level: AUTO
Clk Driving Pull-Up Level: AUTO
Data Driving Pull-Down Level: AUTO
Cmd Driving Pull-Down Level: AUTO
Ctrl Driving Pull-Down Level: AUTO
Clk Driving Pull-Down Level: AUTO
Motherboard Voltage Control
CPU Vcore: 1.25v
CPU Termination | 1.200V: v
CPU PLL | 1.500V: v
CPU Reference | 0.760V: v
MCH Core | 1.100V:1.26 v
MCH Reference | 0.900V: v
MCH/DRAM Ref | 0.900V: v
ICH I/O | 1.500V: v
DRAM Voltage | 1.800V:2.1 v
DRAM Termination | 0.900V: v
Channel A Reference | 0.900V: v
Channel B Reference | 0.900V: v
Thanks in advance
Nikos
Comment