Announcement

Collapse
No announcement yet.

ep45 and corsair xms2 8500 problem at 1066

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    ep45 and corsair xms2 8500 problem at 1066

    Hi all,
    I have the ep45-ds3 board and after I tried a million times the hyperx 8500 to make them work at 1066 I changed them with the xms2 8500 2x2gb but it seems that I have the same problem,please help me figure this out because its going to drive me crazy.
    Here are my settings:

    GIGABYTE GA-EP45_EXTREME
    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster: AUTO
    CPU Clock Ratio: 8x
    Fine CPU Clock Ratio: [0.0]
    CPU Frequency: 2.66Ghz(333x8)

    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control: [Disabled]
    CPU Host Frequency(Mhz): 333 Mhz
    PCI Express Frequency(Mhz): 100 Mhz
    C.I.A. 2: [Disabled]

    Advanced Clock Control [Press Enter]
    CPU Clock Drive: 800mv
    PCI Express Clock Drive: 900mv
    CPU Clock Skew: 0ps
    MCH Clock Skew: 50ps

    DRAM Performance Control
    Performance Enhance: [Standard]
    Extreme Memory Profile (X.M.P.): [Disabled]
    (G)MCH Frequency Latch: [333]
    System Memory Multiplier:3.20
    Memory Frequency (Mhz):1066 Mhz
    DRAM Timing Selectable: [Manual]
    Standard Timing Control
    CAS Latency Time: 5
    tRCD: 5
    tRP: 5
    tRAS: 18 (I tried also 15)

    Advanced Timing Control [Press Enter]
    tRRD:6
    tWTR:14
    tWR:16
    tRFC:75
    tRTP:7
    Command Rate (CMD):2

    >>>>> Channel A
    Channel A Timing Settings: [Press Enter]
    Static tRead Value: 10 I've tried also 12 and 14
    tRD Phase0 Adjustment: Auto
    tRD Phase1 Adjustment: Auto
    tRD Phase2 Adjustment: Auto
    tRD Phase3 Adjustment: Auto
    Trd2rd(Different Rank).: 8
    Twr2wr(Different Rank): 8
    Twr2rd(Different Rank): 7
    Trd2wr(Same/Diff Rank): 9
    Dimm1 Clock Skew Control: Auto
    Dimm2 Clock Skew Control: Auto
    DDR3 Write Training: Auto

    Channel A Driving Settings: [Press Enter]
    Driving Strength Profile: 1066Mhz I 've tried also oc-1200

    Data Driving Pull-Up Level: AUTO
    Cmd Driving Pull-Up Level: AUTO
    Ctrl Driving Pull-Up Level: AUTO
    Clk Driving Pull-Up Level: AUTO

    Data Driving Pull-Down Level: AUTO
    Cmd Driving Pull-Down Level: AUTO
    Ctrl Driving Pull-Down Level: AUTO
    Clk Driving Pull-Down Level: AUTO

    >>>>> Channel B
    Channel B Timing Settings: [Press Enter]
    Static tRead Value: 10 I've tried also 12 and 14
    tRD Phase0 Adjustment: Auto
    tRD Phase1 Adjustment: Auto
    tRD Phase2 Adjustment: Auto
    tRD Phase3 Adjustment: Auto
    Trd2rd(Different Rank).: 8
    Twr2wr(Different Rank): 8
    Twr2rd(Different Rank): 7
    Trd2wr(Same/Diff Rank): 9
    Dimm1 Clock Skew Control: Auto ps
    Dimm2 Clock Skew Control: Auto ps
    DDR3 Write Training: Auto

    Channel B Driving Settings: [Press Enter]
    Driving Strength Profile: 1066Mhz I 've tried also oc-1200

    Data Driving Pull-Up Level: AUTO
    Cmd Driving Pull-Up Level: AUTO
    Ctrl Driving Pull-Up Level: AUTO
    Clk Driving Pull-Up Level: AUTO

    Data Driving Pull-Down Level: AUTO
    Cmd Driving Pull-Down Level: AUTO
    Ctrl Driving Pull-Down Level: AUTO
    Clk Driving Pull-Down Level: AUTO

    Motherboard Voltage Control

    CPU Vcore: 1.25v
    CPU Termination | 1.200V: v
    CPU PLL | 1.500V: v
    CPU Reference | 0.760V: v


    MCH Core | 1.100V:1.26 v
    MCH Reference | 0.900V: v
    MCH/DRAM Ref | 0.900V: v
    ICH I/O | 1.500V: v

    DRAM Voltage | 1.800V:2.1 v
    DRAM Termination | 0.900V: v
    Channel A Reference | 0.900V: v
    Channel B Reference | 0.900V: v


    Thanks in advance
    Nikos
    Tags: None
  • #2
    Re: ep45 and corsair xms2 8500 problem at 1066

    Sorry I forgot my specs:

    Q9400
    GA-ER45-DS3(running f9)
    Geforce GTX 260
    Vista 64x

    Comment

    • #3
      Re: ep45 and corsair xms2 8500 problem at 1066

      See if this helps you any >>>

      MB Intelligent Tweaker(M.I.T.)
      Robust Graphics Booster: AUTO or FAST
      CPU Clock Ratio: 8x
      Fine CPU Clock Ratio: [0.0]
      CPU Frequency: 2.66Ghz(333x8)

      Clock Chip Control
      Standard Clock Control
      CPU Host Clock Control: [Disabled]
      CPU Host Frequency(Mhz): 333 Mhz
      PCI Express Frequency(Mhz): 100 Mhz
      C.I.A. 2: [Disabled]

      Advanced Clock Control [Press Enter]
      CPU Clock Drive: 800mv
      PCI Express Clock Drive: 900mv
      CPU Clock Skew: 0ps
      MCH Clock Skew: 150ps

      DRAM Performance Control
      Performance Enhance: [Standard]
      Extreme Memory Profile (X.M.P.): [Disabled]
      (G)MCH Frequency Latch: [333]
      System Memory Multiplier:3.20
      Memory Frequency (Mhz):1066 Mhz
      DRAM Timing Selectable: [Manual]
      Standard Timing Control
      CAS Latency Time: 5
      tRCD: 5
      tRP: 5
      tRAS: 18 (I tried also 15)

      Advanced Timing Control [Press Enter]
      tRRD:6 << 3-4
      tWTR:14 << 3-6
      tWR:16 << 4-8
      tRFC:75 << 52-62
      tRTP:7 << 3-5
      Command Rate (CMD):2

      >>>>> Channel A
      Channel A Timing Settings: [Press Enter]
      Static tRead Value: 10 I've tried also 12 and 14 (6/7-10 for 333/B MCH Latch)
      tRD Phase0 Adjustment: Auto
      tRD Phase1 Adjustment: Auto
      tRD Phase2 Adjustment: Auto
      tRD Phase3 Adjustment: Auto
      Trd2rd(Different Rank).: 8 << AUTO
      Twr2wr(Different Rank): 8 << AUTO
      Twr2rd(Different Rank): 7 << AUTO
      Trd2wr(Same/Diff Rank): 9 << AUTO
      Dimm1 Clock Skew Control: Auto
      Dimm2 Clock Skew Control: Auto
      DDR3 Write Training: Auto

      Channel A Driving Settings: [Press Enter]
      Driving Strength Profile: 1066Mhz I 've tried also oc-1200 800-1200

      Data Driving Pull-Up Level: AUTO
      Cmd Driving Pull-Up Level: AUTO
      Ctrl Driving Pull-Up Level: AUTO
      Clk Driving Pull-Up Level: AUTO

      Data Driving Pull-Down Level: AUTO
      Cmd Driving Pull-Down Level: AUTO
      Ctrl Driving Pull-Down Level: AUTO
      Clk Driving Pull-Down Level: AUTO

      >>>>> Channel B
      Channel B Timing Settings: [Press Enter]
      Static tRead Value: 10 I've tried also 12 and 14 (6/7-10 for 333/B MCH Latch)
      tRD Phase0 Adjustment: Auto
      tRD Phase1 Adjustment: Auto
      tRD Phase2 Adjustment: Auto
      tRD Phase3 Adjustment: Auto
      Trd2rd(Different Rank).: 8 << AUTO
      Twr2wr(Different Rank): 8 << AUTO
      Twr2rd(Different Rank): 7 << AUTO
      Trd2wr(Same/Diff Rank): 9 << AUTO
      Dimm1 Clock Skew Control: Auto ps
      Dimm2 Clock Skew Control: Auto ps
      DDR3 Write Training: Auto

      Channel B Driving Settings: [Press Enter]
      Driving Strength Profile: 1066Mhz I 've tried also oc-1200 800-1200

      Data Driving Pull-Up Level: AUTO
      Cmd Driving Pull-Up Level: AUTO
      Ctrl Driving Pull-Up Level: AUTO
      Clk Driving Pull-Up Level: AUTO

      Data Driving Pull-Down Level: AUTO
      Cmd Driving Pull-Down Level: AUTO
      Ctrl Driving Pull-Down Level: AUTO
      Clk Driving Pull-Down Level: AUTO

      Motherboard Voltage Control

      CPU Vcore: 1.25v
      CPU Termination | 1.200V: v
      CPU PLL | 1.500V: v
      CPU Reference | 0.760V: v


      MCH Core | 1.100V:1.26 v << Maybe 1.28-1.3
      MCH Reference | 0.900V: v
      MCH/DRAM Ref | 0.900V: v
      ICH I/O | 1.55

      DRAM Voltage | 1.800V:2.1 v 2.0-2.1 (Is your ram 1.9V?)
      DRAM Termination | 0.900V: v
      Channel A Reference | 0.900V: v
      Channel B Reference | 0.900V: v

      Comment

      • #4
        Re: ep45 and corsair xms2 8500 problem at 1066

        THANK YOU
        It works at last, here I write down the settings I used just for enyone who might need them

        GIGABYTE GA-EP45_EXTREME
        MB Intelligent Tweaker(M.I.T.)
        Robust Graphics Booster: AUTO
        CPU Clock Ratio: 8x
        Fine CPU Clock Ratio: [0.0]
        CPU Frequency: 2.66Ghz(333x8)

        Clock Chip Control
        Standard Clock Control
        CPU Host Clock Control: [Disabled]
        CPU Host Frequency(Mhz): 333 Mhz
        PCI Express Frequency(Mhz): 100 Mhz
        C.I.A. 2: [Disabled]

        Advanced Clock Control [Press Enter]
        CPU Clock Drive: 800mv
        PCI Express Clock Drive: 900mv
        CPU Clock Skew: 0ps
        MCH Clock Skew: 150ps

        DRAM Performance Control
        Performance Enhance: [Standard]
        Extreme Memory Profile (X.M.P.): [Disabled]
        (G)MCH Frequency Latch: [333]
        System Memory Multiplier:3.20
        Memory Frequency (Mhz):1066 Mhz
        DRAM Timing Selectable: [Manual]
        Standard Timing Control
        CAS Latency Time: 5
        tRCD: 5
        tRP: 5
        tRAS: 15
        Advanced Timing Control [Press Enter]
        tRRD:3
        tWTR:3
        tWR:4
        tRFC:52
        tRTP:3
        Command Rate (CMD):2

        >>>>> Channel A
        Channel A Timing Settings: [Press Enter]
        Static tRead Value: 10
        tRD Phase0 Adjustment: Auto
        tRD Phase1 Adjustment: Auto
        tRD Phase2 Adjustment: Auto
        tRD Phase3 Adjustment: Auto
        Trd2rd(Different Rank).: 8
        Twr2wr(Different Rank): 8
        Twr2rd(Different Rank): 7
        Trd2wr(Same/Diff Rank): 9
        Dimm1 Clock Skew Control: Auto
        Dimm2 Clock Skew Control: Auto
        DDR3 Write Training: Auto

        Channel A Driving Settings: [Press Enter]
        Driving Strength Profile: 1066Mhz

        Data Driving Pull-Up Level: AUTO
        Cmd Driving Pull-Up Level: AUTO
        Ctrl Driving Pull-Up Level: AUTO
        Clk Driving Pull-Up Level: AUTO

        Data Driving Pull-Down Level: AUTO
        Cmd Driving Pull-Down Level: AUTO
        Ctrl Driving Pull-Down Level: AUTO
        Clk Driving Pull-Down Level: AUTO

        >>>>> Channel B
        Channel B Timing Settings: [Press Enter]
        Static tRead Value: 10
        tRD Phase0 Adjustment: Auto
        tRD Phase1 Adjustment: Auto
        tRD Phase2 Adjustment: Auto
        tRD Phase3 Adjustment: Auto
        Trd2rd(Different Rank).: 8
        Twr2wr(Different Rank): 8
        Twr2rd(Different Rank): 7
        Trd2wr(Same/Diff Rank): 9
        Dimm1 Clock Skew Control: Auto ps
        Dimm2 Clock Skew Control: Auto ps
        DDR3 Write Training: Auto

        Channel B Driving Settings: [Press Enter]
        Driving Strength Profile: 1066Mhz
        Data Driving Pull-Up Level: AUTO
        Cmd Driving Pull-Up Level: AUTO
        Ctrl Driving Pull-Up Level: AUTO
        Clk Driving Pull-Up Level: AUTO

        Data Driving Pull-Down Level: AUTO
        Cmd Driving Pull-Down Level: AUTO
        Ctrl Driving Pull-Down Level: AUTO
        Clk Driving Pull-Down Level: AUTO

        Motherboard Voltage Control

        CPU Vcore: 1.125v
        CPU Termination | 1.200V: v
        CPU PLL | 1.500V: v
        CPU Reference | 0.760V: v


        MCH Core | 1.100V:1.3v
        MCH Reference | 0.920V: v
        MCH/DRAM Ref | 0.920V: v
        ICH I/O | 1.570V: v

        DRAM Voltage | 1.800V:2.1 v
        DRAM Termination | 0.900V: v
        Channel A Reference | 0.900V: v
        Channel B Reference | 0.900V: v


        Thank you again you are great

        Comment

        • #5
          Re: ep45 and corsair xms2 8500 problem at 1066

          Thanks for posting back for others!

          Now you can likely lower your static tRead values to 7-9

          Comment

          Previous template Next
          Working...
          X