p35-ds4 with 8500c rams BSOD

[negrala]

hi all.. i need help i have a p35-ds4 mobo and 2x2gb corsair memories model 8500c and i cant make them run at their stock speed (1066) mhz i have them running at 1000mhz and i still get the problems sometimes can anyone tell me what can i do to fix my problem i dont want to underclock my computer anymore... thnx
here are my computer specs

[Lsdmeasap]

Re: p35-ds4 with 8500c rams BSOD

Please post me a link to your ram's exact model so I can check warrantied voltages, and then please fill this out with your settings as of now and I will advise back >>>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [8] 
Fine Clock Ratio ____________[0.5]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [450] 
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00]
DRAM Timing Selectable_______ SPD __ [Manual]

Performance Enhance = [Standard]

CAS Latency Time________________ ?
Dram RAS# to CAS# Delay_________ ?
Dram RAS# Precharge Delay_______?
Precharge Delay (tRAS)__________ ?

ACT to ACT Delay (tRRD)_________ ?
Rank Write to READ Delay________ ?
Write to Precharge Delay_________ ?
Refresh to ACT Delay______________ ?
Read to Precharge Delay__________ ?
Static tRead Value_______________
Static tRead Phase Adjust________ [Auto]

CPU/PCIEX Clock Driving Control [800mV]
CPU Clock Skew Control [normal]
GMCH Clock Skew Control [Normal]

System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V] 
PCI-E OverVoltage Control_ [+0.1V] 
FSB OverVoltage Control___ [+0.1V] 
(G)MCH OverVoltage Control [+0.1V] 
CPU Voltage Control_______ [1.25]

Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB

[negrala]

Re: p35-ds4 with 8500c rams BSOD

Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [8]
Fine Clock Ratio ____________xxx
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [300]
PCI Express Frequency (Mhz)_______ [auto]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [333]
DRAM Timing Selectable_______ SPD __ [auto]

Performance Enhance = [Standard]

CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 7
Dram RAS# Precharge Delay_______7
Precharge Delay (tRAS)__________ 24

ACT to ACT Delay (tRRD)_________ 4
Rank Write to READ Delay________ 4
Write to Precharge Delay_________ 8
Refresh to ACT Delay______________ 68
Read to Precharge Delay__________ 4
Static tRead Value_______________4
Static tRead Phase Adjust________ 0


System Voltage Control____ [Manual] auto
DDR2 OverVoltage Control__ [+0.300V] normal
PCI-E OverVoltage Control_ [+0.1V] normal
FSB OverVoltage Control___ [+0.1V] normal
(G)MCH OverVoltage Control [+0.1V] normal
CPU Voltage Control_______ [1.25] 1.28750



thats all i could found when i try to run it at 5-5-5-15 it doesnt even boot
my ram model is cm2x2048-8500c5</pre>
</pre>

[VorLonUK]

Re: p35-ds4 with 8500c rams BSOD

I think you've mixed up memory multiplier with the system Bus.

It may be that your board doesn't like the 3.00 multiplier at some settings (mine is like that).

For starters underclock your ram, by setting:-

1) Memory multiplier = 2.40
2) Main memory settings = 5-5-5-15
3) Advanced memory all to Auto; Except,
4) tFRC (Refresh To Act Delay) = 56
5) All voltages to Auto; Except,
6) Set DDR2 Voltage to +0.2volts

From that base, see how your system runs. This way we can rule out other problems. Your memory to full speed can be tweaked later.

[negrala]

Re: p35-ds4 with 8500c rams BSOD

ok ready with that now i have my ram running at 640 mhz with a clock ratio at 9x and a cpu host frequency of 266 what do i do now to get my 1066? thnx

[VorLonUK]

Re: p35-ds4 with 8500c rams BSOD

ok ready with that now i have my ram running at 640 mhz with a clock ratio at 9x and a cpu host frequency of 266 what do i do now to get my 1066? thnx

From your settings I thought you had a 1333 FSB chip, so infact you have a 1066 chip?
I didn't intend for you to start as low as 266 x 2.40 = 640Mhz. I thought your Host frequency was 333 as per the template above in your post.

Ok i can see from the tiny print in the Screenshot now.

Assuming you have no BSOD's now, try changing Just the memory multiplier to 3.00x, leaving the settings I gave you (above) exactly the same.

[negrala]

Re: p35-ds4 with 8500c rams BSOD

ok i set the ratio to 8x and the cpu host to 300 and the memory multiplier to 333 no my ram is running at 1000 mhz thats what u wanted right now what do i do? xD

[VorLonUK]

Re: p35-ds4 with 8500c rams BSOD

You've got a q6600 right? The CPU host frequency should be at 266Mhz for it to run at its normal speed.

[negrala]

Re: p35-ds4 with 8500c rams BSOD

ok so i put it at 266 and the memory multipliear at 400?

[VorLonUK]

Re: p35-ds4 with 8500c rams BSOD

ok so i put it at 266 and the memory multiplier at 400?

Yes - That would be the correct combination for your CPU and your PC8500 (1066Mhz) ram.

In MIT section of bios, you should change the following:-
1) Set the main memory timings to 5-5-5-18
2) Performance Enhance to Standard
3) tRFC (Refresh To Act Delay) to 56

[Lsdmeasap]

Re: p35-ds4 with 8500c rams BSOD

Let me know if you need any further help with this, and as asked before a link to your ram would be needed for me to best advise you

[negrala]

Re: p35-ds4 with 8500c rams BSOD

ok all set im gonna test it now xD, do anyone have a tip to start windows xp faster? and load programs faster?

[Lsdmeasap]

Re: p35-ds4 with 8500c rams BSOD

Let us know how you get along. Ya, you can uninstall Norton to make XP load faster ( J/K, but if you are using it I am serious! )

[negrala]

Re: p35-ds4 with 8500c rams BSOD

no i dont use norton xD i have eset nod32... im talking about the black loading screen that windows displays when u restart or turn on your computer... and when u load all the programs im thinking of removing windows live messenger from the startup its kindda heavy program any suggestion?

[negrala]

Re: p35-ds4 with 8500c rams BSOD

i got a BSOD a few moments ago dont know why :( need help