hi,
i have build up an new pc with
an DS3, e8400 and 2x2gb apogee ddr2 1066 5-5-5-15
bios is v.F9 and the apogees will run with 1.9 at 1066
(on my old mainboard and P35 DS3 they run at 1180 with 2.0v)
for now i have OC'ed my cpu too 4ghz like this:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: AUTO
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 4.00ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 445Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 1068
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Advanced Timing Control
tRRD...........................................aut o (3)
tWTR..........................................auto (3)
tWR............................................aut o (6)
tRFC...........................................52
tRTP...........................................aut o (3)
Command Rate (CMD) ....................:auto (0)
Driving Strength Profiles
Driving Strength ............................1066
Channel A
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Enabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
CPU and northbridge are watercooled, so they get not warm.
for now system seems to be stable, is there any fault in my config?
and *how can i increase my RAM performance, because i can't get the
2x2gb over 1068mhz stable.
how can i do this, my older P35-DS3 reaced more ram performance so will
get this again if this is possible.
the apogess run very smooth, i have run them at 580 1:1 at 2.2v
(max. for this ram is 2.3v)
thx for reading
alice
i have build up an new pc with
an DS3, e8400 and 2x2gb apogee ddr2 1066 5-5-5-15
bios is v.F9 and the apogees will run with 1.9 at 1066
(on my old mainboard and P35 DS3 they run at 1180 with 2.0v)
for now i have OC'ed my cpu too 4ghz like this:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: AUTO
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 4.00ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 445Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 1068
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Advanced Timing Control
tRRD...........................................aut o (3)
tWTR..........................................auto (3)
tWR............................................aut o (6)
tRFC...........................................52
tRTP...........................................aut o (3)
Command Rate (CMD) ....................:auto (0)
Driving Strength Profiles
Driving Strength ............................1066
Channel A
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Enabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
CPU and northbridge are watercooled, so they get not warm.
for now system seems to be stable, is there any fault in my config?
and *how can i increase my RAM performance, because i can't get the
2x2gb over 1068mhz stable.
how can i do this, my older P35-DS3 reaced more ram performance so will
get this again if this is possible.
the apogess run very smooth, i have run them at 580 1:1 at 2.2v
(max. for this ram is 2.3v)
thx for reading
alice
Comment