Hello from a new member of these forums.
My specs are:
EP43-DS3 (Bios F8)
E2160
4 x 1 PC6400 Ballistix (2 sticks older, 2 sticks new due to RMA)
Sapphire X1950 Pro
Corsair 620w psu
Arctic Cooling Freezer Pro with AS5
I used the above in my now replaced (RMA) P35C DS3R and got the chip to 3g and ram to 1000m very easily and this was stable for nearly a year, until the board and one stick of ram died, hence the new mobo and 2 sticks of new ram, which I assembled about 2 weeks ago.
Until yesterday, I was able to get the chip at 2.7g and was able to play games easily, but when I restart, the system either went into a loop and when I was able to get into bios, it would come up with the red warning message, so I saved the settings again and it would either loop again, or after numerous tries, it would eventually boot into Vista x64.
Today, with the settings below, it now loads up at the stock 1.8g and 800 ram settings and no matter how many times I've tweaked the settings, it will only boot at stock.
I've tried booting with just the old and then the new ram fitted, the same thing happens.
I hope the above makes sense, as I've been out of the overclocking scene for a while.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: x9
Fine CPU Clock Ratio.....................:.Don't have this option
CPU Frequency ...........................: 2.700MHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 300Mhz
PCI Express Frequency (Mhz) .........:Set to 100
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 200MHz
System Memory Multiplier ..............: 2.66c
Memory Frequency (Mhz) ..............: 800MHz
DRAM Timing Selectable ................: [Autol]
Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 5
tRAS.......................................... 15
Advanced Timing Control
tRRD........................................... 3 - Auto
tWTR.......................................... 3 - Auto
tWR............................................ 6 - Auto
tRFC........................................... 52 - Auto
tRTP........................................... 3 - Auto
Command Rate (CMD) ....................:0 - Auto
Channel A
Static tRead Value.........................:3 - Auto
tRD Phase0 Adjustment...................:0 - Auto
tRD Phase1 Adjustment...................:0 - Auto
tRD Phase2 Adjustment .................:0 - Auto
tRD Phase3 Adjustment..................:0 - Auto
Trd2rd(Different Rank)....................:6 - Auto
Twr2wr(Different Rank)...................:6 - Auto
Twr2rd(Different Rank)...................:5 - Auto
Trd2wr(Same/Diff Rank)..................:8 - Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................: 4
tRD Phase0 Adjustment...................:9 - Auto
tRD Phase1 Adjustment...................:1 - Auto
tRD Phase2 Adjustment .................:0 - Auto
tRD Phase3 Adjustment..................:0 - Auto
Trd2rd(Different Rank)....................:6 - Auto
Twr2wr(Different Rank)...................:6 - Auto
Twr2rd(Different Rank)...................:5 - Auto
Trd2wr(Same/Diff Rank)..................:8 - Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
CPU
CPU Vcore….……….........................: 1.3250V
CPU Termination…..... 1.200V*.......: Auto
CPU PLL…………………....1.500V*.......: Auto
CPU Referen.…………....0.760V*.......: Auto
MCH/ICH
MCH Core…………….....1.100V...........: << 1.20V
MCH Reference….…….0.760V...........; Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.500V............: Auto
DRAM
DRAM Voltage ……....1.800V............: 2.0V
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
My specs are:
EP43-DS3 (Bios F8)
E2160
4 x 1 PC6400 Ballistix (2 sticks older, 2 sticks new due to RMA)
Sapphire X1950 Pro
Corsair 620w psu
Arctic Cooling Freezer Pro with AS5
I used the above in my now replaced (RMA) P35C DS3R and got the chip to 3g and ram to 1000m very easily and this was stable for nearly a year, until the board and one stick of ram died, hence the new mobo and 2 sticks of new ram, which I assembled about 2 weeks ago.
Until yesterday, I was able to get the chip at 2.7g and was able to play games easily, but when I restart, the system either went into a loop and when I was able to get into bios, it would come up with the red warning message, so I saved the settings again and it would either loop again, or after numerous tries, it would eventually boot into Vista x64.
Today, with the settings below, it now loads up at the stock 1.8g and 800 ram settings and no matter how many times I've tweaked the settings, it will only boot at stock.
I've tried booting with just the old and then the new ram fitted, the same thing happens.
I hope the above makes sense, as I've been out of the overclocking scene for a while.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: x9
Fine CPU Clock Ratio.....................:.Don't have this option
CPU Frequency ...........................: 2.700MHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 300Mhz
PCI Express Frequency (Mhz) .........:Set to 100
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 200MHz
System Memory Multiplier ..............: 2.66c
Memory Frequency (Mhz) ..............: 800MHz
DRAM Timing Selectable ................: [Autol]
Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 5
tRAS.......................................... 15
Advanced Timing Control
tRRD........................................... 3 - Auto
tWTR.......................................... 3 - Auto
tWR............................................ 6 - Auto
tRFC........................................... 52 - Auto
tRTP........................................... 3 - Auto
Command Rate (CMD) ....................:0 - Auto
Channel A
Static tRead Value.........................:3 - Auto
tRD Phase0 Adjustment...................:0 - Auto
tRD Phase1 Adjustment...................:0 - Auto
tRD Phase2 Adjustment .................:0 - Auto
tRD Phase3 Adjustment..................:0 - Auto
Trd2rd(Different Rank)....................:6 - Auto
Twr2wr(Different Rank)...................:6 - Auto
Twr2rd(Different Rank)...................:5 - Auto
Trd2wr(Same/Diff Rank)..................:8 - Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................: 4
tRD Phase0 Adjustment...................:9 - Auto
tRD Phase1 Adjustment...................:1 - Auto
tRD Phase2 Adjustment .................:0 - Auto
tRD Phase3 Adjustment..................:0 - Auto
Trd2rd(Different Rank)....................:6 - Auto
Twr2wr(Different Rank)...................:6 - Auto
Twr2rd(Different Rank)...................:5 - Auto
Trd2wr(Same/Diff Rank)..................:8 - Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
CPU
CPU Vcore….……….........................: 1.3250V
CPU Termination…..... 1.200V*.......: Auto
CPU PLL…………………....1.500V*.......: Auto
CPU Referen.…………....0.760V*.......: Auto
MCH/ICH
MCH Core…………….....1.100V...........: << 1.20V
MCH Reference….…….0.760V...........; Auto
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.500V............: Auto
DRAM
DRAM Voltage ……....1.800V............: 2.0V
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Comment