If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
I've made improvements to the airflow inside my case which has dropped the temps (both idle and full load) of my case and CPU. I'll also be installing a new CPU cooler which will help.
I can't seem to get my OC to boot at any FSB at or above 400MHz. I am Prime95 and Memtest86 stable at 3.35GHz (395FSB x 8.5multiplier). My memory settings are as you (Lsdmeasap) suggested in the posts above:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.5
CPU Frequency ...........................: 3.35GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 395Mhz
PCI Express Frequency (Mhz) .........:Set to 100
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mv
PCI Express Clock Drive.................: 900mv
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [333] I tried 400 also
System Memory Multiplier ..............: AUTO
Memory Frequency (Mhz) ..............: 960Mhz (I think)
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Advanced Timing Control
tRRD...........................................3-4
tWTR.......................................... 4-6 (9-11 Benchmark to see if better)
tWR............................................3-6
tRFC........................................... 62-75 (Will be needed for 8GB, Maybe more, maybe less. Start high for now)
Channel A
Static tRead Value.........................:7-12
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:7-12
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.25000
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< Leave
CPU Reference2………,,0.800V*.......:<<< Leave
MCH/ICH
MCH Core…………….....1.300V...........: << 1.3+ will be needed for 8GB
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave
DRAM
DRAM Voltage ……....1.900V............: 1.8-2.0 (MAX Warrantied is 2.1V)
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
My system is rock solid at 3.35 GHz with a FSB of 395 but as a soon as I try increasing FSB to 400 or 401 or 402 or 412 or 430 it refuses to POST. I've tried increasing CPU Vcore up a notch at a time (up to 3 increments max). I've tried loosening memory timings to 5-5-5-15 and 5-5-5-18 with no luck. I've tried manually setting memory multiplie to both 2.0 and 2.4 with no success. I've even tried a 'Hail Mary' pass attempt setting FSB to 430 with MCH set to 400 all with no success.
Any suggestions to what I can do or should not be doing to achieve an OC of 3.4GHz or more (not that 3.35GHz isn't good enough really)? I just can't understand the wall I've hit at FSB of 400MHz.
Thanks.
Last edited by CanyonRunner; 10-10-2008, 12:35 PM.
You will have to use 400 MCH latch for 400+ FSB, static tread of 8+, and set twr, twtr, and trfc very high until you get booted thru. Use manually set memory mutli of 2.00 and use 2.1V for now as well
You are likely going to need to set the termination and PLL manually, as well as increase the vcore. I would think 1.34 or so Termination and 1.5-1.56 Pll should help you
I would also go ahead and set Driving strength profile to 1066, I find that the next one above the speed you are trying to run the ram works best
Comment