Motherboard : Gigabyte GA-EP43-DS3
Bios : F10B
Processor : Q6600 , G0 .. with Spire Thermax Eclipse II Cooler, TX-$ TIM
PSU : Cooler Master eXtreme Power Plus 460W
Ram : Kingston DDR2 800MHz 2GB x 2
VGA : Gigabyte NVIDIA GeForce 9800 GT 1GB
HDD : Western Digital 1 Terabyte
OS : Windows 7 Ultimate 32bit
Guys im having a problem OC to 3.4Ghz.
im using : 378x9 , ive set my ram according to its timing.
i was having difficulty running prime 95. it would fail within the 1st minute.
I believe im having a problem with voltage. so i had to up my Vcore to 1.52 bios, and MCH Core 1.3 .. DRam 1.8V ...the rest i kept at normal. with this i was able to run prime for about 2 hours.Vcore was around 1.46.. then i notice the Vcore suddenly dropped to 1.42 and than one of the prime95 workers failed saying fatal error less the 0.4
I have a G0 chip, i believe 3.4 should be an easy task...my temp wont pass 60.
any idea what im doing wrong?
EDIT: im now running this.
400 x 8 Multiplier = 3.2Ghz
Ram Timing = 6-6-6-18 ..1:1
Cpu V-core 1.5V (bios) . HW Monitor 1.46V idle. 1.41~1.43 on load.
Cpu Termination : 1.3
CPU PLL : 1.59
CPU reference : Auto
MCH Core - 1.3
MCH Ref - Auto
MCH Dram Ref : Auto
MCH ICH - Auto
Dram Volt- 1.8v
Rest all on auto.
running prime now about 3 hours on 3.2Ghz 400x8. so far seems ok. but my real target is 3.4Ghz ~ 3.6Ghz, will this be achievable ?
Bios : F10B
Processor : Q6600 , G0 .. with Spire Thermax Eclipse II Cooler, TX-$ TIM
PSU : Cooler Master eXtreme Power Plus 460W
Ram : Kingston DDR2 800MHz 2GB x 2
VGA : Gigabyte NVIDIA GeForce 9800 GT 1GB
HDD : Western Digital 1 Terabyte
OS : Windows 7 Ultimate 32bit
Guys im having a problem OC to 3.4Ghz.
im using : 378x9 , ive set my ram according to its timing.
i was having difficulty running prime 95. it would fail within the 1st minute.
I believe im having a problem with voltage. so i had to up my Vcore to 1.52 bios, and MCH Core 1.3 .. DRam 1.8V ...the rest i kept at normal. with this i was able to run prime for about 2 hours.Vcore was around 1.46.. then i notice the Vcore suddenly dropped to 1.42 and than one of the prime95 workers failed saying fatal error less the 0.4
I have a G0 chip, i believe 3.4 should be an easy task...my temp wont pass 60.
any idea what im doing wrong?
EDIT: im now running this.
400 x 8 Multiplier = 3.2Ghz
Ram Timing = 6-6-6-18 ..1:1
Cpu V-core 1.5V (bios) . HW Monitor 1.46V idle. 1.41~1.43 on load.
Cpu Termination : 1.3
CPU PLL : 1.59
CPU reference : Auto
MCH Core - 1.3
MCH Ref - Auto
MCH Dram Ref : Auto
MCH ICH - Auto
Dram Volt- 1.8v
Rest all on auto.
running prime now about 3 hours on 3.2Ghz 400x8. so far seems ok. but my real target is 3.4Ghz ~ 3.6Ghz, will this be achievable ?
Comment