I am trying to OC my rig but I can only get to 343 any thing past that and it wont boot. I can change the voltage and all but it wont let me go higher. I have read that this processor can go to at least 500. any help will be greatly appreciated!!!!!!!
BIOS settings
P45/P43
(Also includes G45/G43 Variants)
Simplified Template For users who may not be sure of anything in the MIT Section
Motherboard: Model: Rev#: Bios Version:2.1 GA G41MT-S2PT
Cpu: Model Intel #8400
Ram: Brand, Model/Part#, Link to your ram's specs= PNY, Model#MD8192KD3-1333, pny.com
Power Supply Unit: Brand, Model#, Wattage= A-Power, AGS550, 550 watts total power
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [9]
Fine CPU Clock Ratio ----------------- : [0.5] <-- ignore if not available
CPU Frequency ---------------------: 3.25GHz [343] <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [343]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [xxx] N/A
Advanced Clock Control ------- [Press Enter]Can not get into
CPU Clock Drive ---------------------- : [xxx] N/A
PCI Express Clock Drive -------------- : [xxx] N/A
CPU Clock Skew (ps) ------------------ : [xxx] N/A
MCH Clock Skew (ps) ------------------ : [xxx] N/A
DRAM Performance Control
Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [xxx] N/A <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [333]
System Memory Multiplier -------------- : [Manual] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [Auto] 1333 1098
DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- 9 ---------- : [9]
tRCD ------------------- 9 ---------- : [9]
tRP --------------------- 9 ---------- : [9]
tRAS ------------------- 24 ---------- : [24]
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles N/A
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A Timing Settings
Channel A Driving Settings
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
DDR Write Leveling ----------------------: [AUTO]
DDR Write Training ----------------------: [Auto}
Channel B Timing Settings
Channel B Driving Settings
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [xxx] N/A
CPU Vcore --------------- 1.08750v ---- : [Auto]
CPU Termination --------- 1.200v ----- : [xxx] N/A
CPU PLL ----------------- ?.???V* ----- : [xxx] N/A
CPU Reference ----------- ?.???V* ----- : [xxx] N/A
CPU Reference2 ---------- ?.???V* ----- : [xxx] N/A
MCH/ICH
MCH Core ---------------- ?.???V ------- : [xxx] N/A
MCH Reference ----------- ?.???V ------- : [xxx] N/A
MCH/DRAM Ref ------------ ?.???V ------ : [xxx] N/A
ICH I/O ----------------- ?.???V ------- : [xxx] N/A
ICH Core ---------------- ?.???V ------- : [xxx] N/A
DRAM
DRAM Voltage ------------ 1.500V ------- : [Auto]
DRAM Termination -------- ?.???V ------- : [xxx] N/A
Channel A Reference ----- ?.???V ------- : [xxx] N/A
Channel B Reference ----- ?.???V ------- : [xxx] N/A
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [xxx] N/A
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Enabled]
Virtualization Technology -------------- : [Enabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [xxx] N/A
USB Storage Function ------------------: [Enabled]
BIOS settings
P45/P43
(Also includes G45/G43 Variants)
Simplified Template For users who may not be sure of anything in the MIT Section
Motherboard: Model: Rev#: Bios Version:2.1 GA G41MT-S2PT
Cpu: Model Intel #8400
Ram: Brand, Model/Part#, Link to your ram's specs= PNY, Model#MD8192KD3-1333, pny.com
Power Supply Unit: Brand, Model#, Wattage= A-Power, AGS550, 550 watts total power
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [9]
Fine CPU Clock Ratio ----------------- : [0.5] <-- ignore if not available
CPU Frequency ---------------------: 3.25GHz [343] <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [343]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [xxx] N/A
Advanced Clock Control ------- [Press Enter]Can not get into
CPU Clock Drive ---------------------- : [xxx] N/A
PCI Express Clock Drive -------------- : [xxx] N/A
CPU Clock Skew (ps) ------------------ : [xxx] N/A
MCH Clock Skew (ps) ------------------ : [xxx] N/A
DRAM Performance Control
Performance Enhance ------------------- : [Standard] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [xxx] N/A <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [333]
System Memory Multiplier -------------- : [Manual] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [Auto] 1333 1098
DRAM Timing Selectable ---------------- : [Manual] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- 9 ---------- : [9]
tRCD ------------------- 9 ---------- : [9]
tRP --------------------- 9 ---------- : [9]
tRAS ------------------- 24 ---------- : [24]
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles N/A
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A Timing Settings
Channel A Driving Settings
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
DDR Write Leveling ----------------------: [AUTO]
DDR Write Training ----------------------: [Auto}
Channel B Timing Settings
Channel B Driving Settings
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [xxx] N/A
CPU Vcore --------------- 1.08750v ---- : [Auto]
CPU Termination --------- 1.200v ----- : [xxx] N/A
CPU PLL ----------------- ?.???V* ----- : [xxx] N/A
CPU Reference ----------- ?.???V* ----- : [xxx] N/A
CPU Reference2 ---------- ?.???V* ----- : [xxx] N/A
MCH/ICH
MCH Core ---------------- ?.???V ------- : [xxx] N/A
MCH Reference ----------- ?.???V ------- : [xxx] N/A
MCH/DRAM Ref ------------ ?.???V ------ : [xxx] N/A
ICH I/O ----------------- ?.???V ------- : [xxx] N/A
ICH Core ---------------- ?.???V ------- : [xxx] N/A
DRAM
DRAM Voltage ------------ 1.500V ------- : [Auto]
DRAM Termination -------- ?.???V ------- : [xxx] N/A
Channel A Reference ----- ?.???V ------- : [xxx] N/A
Channel B Reference ----- ?.???V ------- : [xxx] N/A
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [xxx] N/A
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Enabled]
Virtualization Technology -------------- : [Enabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [xxx] N/A
USB Storage Function ------------------: [Enabled]
Comment