If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
GA-X58A-UD9 Bios F6 MOD Complete
Updated with...
IRST 11.6.0.1702
Realtek 2.51
Marvell Bios Version 1.0.0.1033 / Firmware 2.2.0.1125
After flash is complete, shut down fully and switch off PSU, wait one minute and clear CMOS. Then turn on, boot to BIOS and load optimized and save/apply/reboot back to the BIOS. Once in the BIOS again set AHCI settings and Marvell Firmware mode to "Force", then save/apply/reboot and let it load through to windows, before that happens Marvell Firmware will update and board will reboot.*
GA-X58A-UD7 Rev 1.0 Bios F9d Mod Complete
Updated with...
IRST 11.6.0.1702
Realteck 2.51
Jmicron 1.07.28
Marvell BIOS 1.0.01033 / Firmware 2.2.0.1125
After flash is complete, shut down fully and switch off PSU, wait one minute and clear CMOS. Then turn on, boot to BIOS and load optimized and save/apply/reboot back to the BIOS. Once in the BIOS again set AHCI settings and Marvell Firmware mode to "Force", then save/apply/reboot and let it load through to windows, before that happens Marvell Firmware will update and board will reboot.*
GA-X58A-UD5 Rev 2.0 Bios Ff3 Complete Mod
Update with...
IRST 11.6.0.1702
Realtek 2.51
Jmicron 1.07.28
Marvell Bios Version 1.0.0.1033 / Firmware 2.2.0.1125
After flash is complete, shut down fully and switch off PSU, wait one minute and clear CMOS. Then turn on, boot to BIOS and load optimized and save/apply/reboot back to the BIOS. Once in the BIOS again set AHCI settings and Marvell Firmware mode to "Force", then save/apply/reboot and let it load through to windows, before that happens Marvell Firmware will update and board will reboot.*
Hello everyone this is my first post here.
Thank you for all the work you do, I follow some time now and I have one of your MODbios
Why there is not a MOD for X58AUD7 / rev.2 with last IRST OROM
It is not necessary for rev.2 ?
I tried it myself but QFLASH tells me that the bios is not 'valid, despite following all instructions in the tutorial.
GA-X58A-UD7 Rev 2.0 Bios FD14 Mod Complete
Updated with...
IRST 11.6.0.1702
Realtek 2.51
Jmicron 1.07.28
Marvell BIOS 1.0.01033 / Firmware 2.2.0.1125
After flash is complete, shut down fully and switch off PSU, wait one minute and clear CMOS. Then turn on, boot to BIOS and load optimized and save/apply/reboot back to the BIOS. Once in the BIOS again set AHCI settings and Marvell Firmware mode to "Force", then save/apply/reboot and let it load through to windows, before that happens Marvell Firmware will update and board will reboot.*
GA-X58A-UD7 Rev 2.0 Bios FD14 Mod Complete
Updated with...
IRST 11.6.0.1702
Realtek 2.51
Jmicron 1.07.28
Marvell BIOS 1.0.01033 / Firmware 2.2.0.1125
If you can't find the bios you want with the latest oroms, you make a requests in this thread and sooner or later someone will fulfill that request.
On previous pages, I mentioned had problems updating BIOS of my EP45-DS3R. After using my PC with 11i BIOS with settings below my preference, just now I got the courage to try again. So I re-flashed my BIOS with 11i modded BIOS, this time made sure to choose clearing DMI pool data. Unfortunately I had the blinking cursor screen after BIOS and failed to boot. Tried multiple times, PC only booted on optimised settings and some one or two more settings onto that. Any more customising than that failed the boot.
Then I tried UNmodded 11i, again same scenario.
And then I tried 11e, latest BIOS on Gigabyte's official page of the MB. This time with all the settings i wanted -except OC for now- even with AHCI, PC successfully booted.
Tough unfortunately 11e doesn't have two options 11i had; to add 0.5+ multiplier to CPU and a quick boot option (not sure how much this effects, i didn't notice anything).
Can anyone by any chance compare 11i between 11e to see what might be wrong and possibly fix it? I could really use those two options...
GA-X58A-UD5 Rev 1.0 Bios F8b Complete Mod
Update with...
IRST 11.6.0.1702
Realtek 2.51
Jmicron 1.07.28
Marvell Bios Version 1.0.0.1033 / Firmware 2.2.0.1125
After flash is complete, shut down fully and switch off PSU, wait one minute and clear CMOS. Then turn on, boot to BIOS and load optimized and save/apply/reboot back to the BIOS. Once in the BIOS again set AHCI settings and Marvell Firmware mode to "Force", then save/apply/reboot and let it load through to windows, before that happens Marvell Firmware will update and board will reboot.*
Comment