MB Intelligent Tweaker(M.I.T.) Robust Graphics Booster ...............: Auto or Fast CPU Clock Ratio ..........................: 9 Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: 3.6/4.05 Clock Chip Control Standard Clock Control CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 401 for 3.6 / 450 for 4Ghz PCI Express Frequency (Mhz) .........:Set to 100 C.I.A.2 .................................:[Disabled] Advanced Clock Control [Press Enter] CPU Clock Drive...........................: <<< 800 PCI Express Clock Drive.................: <<< 900 CPU Clock Skew (ps)....................: <<< MCH Clock Skew (ps)...................: <<< DRAM Performance Control Performance Enhance...................: [STANDARD] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [Auto] System Memory Multiplier ..............: 2.00D (2.00B may work for you as well, it would be better but is harder to get stable often at high FSB) Memory Frequency (Mhz) ..............: 800/900Mhz DRAM Timing Selectable ................: [Manual] Standard Timing Control CAS Latency Time........................5 tRCD .........................................5 tRP'...........................................5 tRAS..........................................15/18 Advanced Timing Control tRRD...........................................3-4 tWTR..........................................3-5 tWR............................................4-6 tRFC...........................................52-62 if 4GB, if only 2GB or 2x1GB 42-48 should be fine tRTP...........................................3-5 Command Rate (CMD) ....................:2 Driving Strength Profiles Driving Strength ............................800/1066 (Test both) Channel A Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps Channel B Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps Motherboard Voltage Control Voltage Type.………... Manual CPU CPU Vcore….……….........................:1.25-1.36 (All up to your chip) CPU Termination…..... 1.200V*.......: <<< 1.2-1.36 (1.2-1.28 likely plenty for 3.6) CPU PLL…………………....1.500V*.......: << 1.5-1.58 CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly MCH/ICH MCH Core…………….....1.100V...........: << 1.2-1.3 (1.22-1.26 likely good) Those settings only needed if you have 4GB, auto should be fine if this is only 2GB of memory you are using, but a little bump might help if you have stability issues. MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.550V............: <<< 1.5-1.6 ICH Core…………...……1.100V............: <<< 1.1x-1.2 DRAM DRAM Voltage ……....1.800V............:1.9-2.0 DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave Advanced Settings Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC Integrated Peripherals Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Tweet
Comment