Ud3p & e8400

[Triton05]

Re: Ud3p & e8400

I say thats stable :)

[Tyreman]

Re: Ud3p & e8400

11 hours now i will keep going

[Lsdmeasap]

Re: Ud3p & e8400

24 hours yet?

[Tyreman]

Re: Ud3p & e8400

Hey Lsdmeasap
15 hours 2 min and secs

[Lsdmeasap]

Re: Ud3p & e8400

Nice, I bet you make it to 24 hours then!

[kpo6969]

Re: Ud3p & e8400

Greetings Lsdmeasap, it's been awhile.
I have a EP45-UD3P on the way to replace my old reliable P35-DS3L. Any issues I may have running 8GB G. Skill 8800PI (original, not the blue)? What I run now is in my sig. Board is rev 1.1 and I believe F8 is on it.
Thanks

[Lsdmeasap]

Re: Ud3p & e8400

Greetings Lsdmeasap, it's been awhile.
I have a EP45-UD3P on the way to replace my old reliable P35-DS3L. Any issues I may have running 8GB G. Skill 8800PI (original, not the blue)? What I run now is in my sig. Board is rev 1.1 and I believe F8 is on it.
Thanks

Ya I saw you mentioned that over at OCN. Shouldn't have any issues with P45, you may have to use 1 higher tRD though, but that's just how the chipset works performance will still be the same.

Everything else should run ok just the same, get ready for a much more advanced BIOS though! You will also have direct input voltage values instead of +0.1, ect, so that makes things nice!

[kpo6969]

Re: Ud3p & e8400

Thanks
Is F10 recommended to flash to from F8?

[Lsdmeasap]

Re: Ud3p & e8400

You can flash from any BIOS to any BIOS, as long as CPU is supported, be sure to use Qflash.

Recommended would be the latest, F11C

http://www.fileden.com/files/2009/12/20/2696817/ep45ud3p.11c.zip

But if it's a revision 1.6 board then use FE

http://download.gigabyte.us/FileList/BIOS/motherboard_bios_ga-ep45-ud3p_1.6_fe.exe

[kpo6969]

Re: Ud3p & e8400

Thanks your the man. That's why I'm using F9c instead of F9 on my DS3L.

[Lsdmeasap]

Re: Ud3p & e8400

Anytime!

Be sure to read the guide as well if you forget how to flash safely

http://forums.tweaktown.com/gigabyte/27576-bios-flashing-how-qflash-guide.html

When does the board arrive?

[Tyreman]

Re: Ud3p & e8400

Screenies
Orthos part way thru and at 24 hours and still running
will close it soon

[Tyreman]

Re: Ud3p & e8400

Final template of Screenies
All screens taken under load running orthos
no eist disabled

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .........Auto
CPU Clock Ratio .................9
Fine CPU Clock Ratio ............0.0
CPU Frequency ...................4.44(444x9)3996 3.96GHz.
Clock Chip Control
Standard Clock Control
CPU Host Clock Control............Enabled
CPU Host Frequency (Mhz) .........444
PCI Express Frequency (Mhz) ......100 Lock
C.I.A.2 ..........................Disabled
Advanced Clock Control[Press Enter]
CPU Clock Drive...................800
PCI Express Clock Drive...........900
CPU Clock Skew (ps)...............0ps
MCH Clock Skew (ps)...............0ps
DRAM Performance Control
Performance Enhance................Standard
Extreme Memory Profile (X.M.P.)....Disabled
(G)MCH Frequency Latch.............400
System Memory Multiplier ..........2.00D “D” straps 400fsb
Memory Frequency (Mhz) ............800 @ 888mhz 1:1
DRAM Timing Selectable ............Manual
Standard Timing Control
CAS Latency Time...................5
tRCD ..............................5
tRP'...............................5
tRAS...............................12
Advanced Timing Control
tRRD...............................auto
tWTR...............................auto
tWR................................auto
tRFC...............................auto
tRTP...............................auto
Command Rate (CMD) ................2T
Driving Strength Profiles
Driving Strength ...................1066
Channel A
Static tRead Value..................9
tRD Phase0 Adjustment...............Auto
tRD Phase1 Adjustment...............Auto
tRD Phase2 Adjustment ..............Auto
tRD Phase3 Adjustment...............Auto
Trd2rd(Different Rank)..............Auto
Twr2wr(Different Rank)..............Auto
Twr2rd(Different Rank)..............Auto
Trd2wr(Same/Diff Rank)..............Auto
Dimm1 Clock Skew Control............Auto
Dimm2 Clock Skew Control............Auto
Channel B
Static tRead Value.....................9
tRD Phase0 Adjustment..................Auto
tRD Phase1 Adjustment..................Auto
tRD Phase2 Adjustment .................Auto
tRD Phase3 Adjustment..................Auto
Trd2rd(Different Rank).................Auto
Twr2wr(Different Rank).................Auto
Twr2rd(Different Rank).................Auto
Trd2wr(Same/Diff Rank).................Auto
Dimm1 Clock Skew Control...............Auto
Dimm2 Clock Skew Control...............Auto
Motherboard Voltage Control
Voltage Type... Manual
CPU
Load Line..................Disabled
CPU V core.................125625V
CPU Termination…1.200V.....1.200V
CPU PLL.........1.500V.....1.500V
CPU Reference...0.760V.....Auto
MCH/ICH
MCH Core……........1.24V Northbridge
MCH Reference….…….0.757V....Auto
MCH/DRAM Ref.…....0.900V....1.04
ICH I/O……………….....1.500V....1.500V
ICH Core…………......1.100V....1.200V
DRAM
DRAM Voltage ……....1.800V...2.08V
DRAM Termination .…0.900V...1.04
Channel A Reference 0.900V..1.04
Channel B Reference 0.900V..1.04
Advanced BIOS Features
Limit CPUID Max. to 3 .......Disabled
No-Execute Memory Protect ...Enabled
CPU Enhanced Halt (C1E) .....Enabled
C2/C2E State Support ........Disabled
x C4/C4E State Support ......Disabled
CPU Thermal Monitor 2 (TM2) .Enabled
CPU EIST Function ...........Enabled
Bios F-10

[kpo6969]

Re: Ud3p & e8400

Anytime!

Be sure to read the guide as well if you forget how to flash safely

http://forums.tweaktown.com/gigabyte/27576-bios-flashing-how-qflash-guide.html

When does the board arrive?

Wed-Thurs
Thanks

[Lsdmeasap]

Re: Ud3p & e8400

Nice n Stable Tyreman, good tweaking!


Good luck setting things up Kpo6969, let us know how you get along