Hi all,
Noob here so bear with me. I recently bought the following:
-i7 920 D0 cpu
-X58A-UD3R mobo
-Patriot Viper Extreme RAM PC3 12800 8-8-8-24 (PVT36G1600LLK) Memory
-Lian Li PC-B25F Case
-Scythe Mugen 2 cpu cooler (mounting required the fan to be raised by about 10mm due to the Viper memory)
-Forgot thermal paste (didn't see it in the Scythe box either!) so bought cheap Spire sp-700 (should be getting IC Diamond soon)
-Antec Truepower 750w PSU
-Sapphire HD5850 vapor-x
Installed everything and initially my temps were 82C! Wiped most of the thermal paste off using an isopropyl wipe to leave a tiny amount on the cpu (can nearly see the text on the cpu).
Temps are now stable at 48-50C when only in BIOS. Have recently put settings on XMP Profile1 and DRAM voltage to 1.66v. So the RAM speed is now 1600Mhz.
Have tried setting the fans to either WMP or voltage. No real change. Voltage option takes the temp up to stable 50C.
Even though the Mugen 2 instructions aren't clear I'm very sure I put the fan the right way round. Nevertheless am about to switch it round just in case the diagram was wrong.
Edit: The fan on this difficult-to-install cooler was indeed the right way round. Well at least I am sure now!
CPU cooler is on nice and tight. I have reinstalled it 5 times to make sure. Then saw I could make the back extra strong as the Lian Li case (not sure if all cases do this) as a naked bit on the rearside of the mobo which I used to tighten the screws that side. They're nice and tight now.
My room temp now (midnight) is 27.3C/81.1F
Any suggestions?
Please let it be a cool one (groan)
Thanks, GinZ
Noob here so bear with me. I recently bought the following:
-i7 920 D0 cpu
-X58A-UD3R mobo
-Patriot Viper Extreme RAM PC3 12800 8-8-8-24 (PVT36G1600LLK) Memory
-Lian Li PC-B25F Case
-Scythe Mugen 2 cpu cooler (mounting required the fan to be raised by about 10mm due to the Viper memory)
-Forgot thermal paste (didn't see it in the Scythe box either!) so bought cheap Spire sp-700 (should be getting IC Diamond soon)
-Antec Truepower 750w PSU
-Sapphire HD5850 vapor-x
Installed everything and initially my temps were 82C! Wiped most of the thermal paste off using an isopropyl wipe to leave a tiny amount on the cpu (can nearly see the text on the cpu).
Temps are now stable at 48-50C when only in BIOS. Have recently put settings on XMP Profile1 and DRAM voltage to 1.66v. So the RAM speed is now 1600Mhz.
Have tried setting the fans to either WMP or voltage. No real change. Voltage option takes the temp up to stable 50C.
Even though the Mugen 2 instructions aren't clear I'm very sure I put the fan the right way round. Nevertheless am about to switch it round just in case the diagram was wrong.
Edit: The fan on this difficult-to-install cooler was indeed the right way round. Well at least I am sure now!
CPU cooler is on nice and tight. I have reinstalled it 5 times to make sure. Then saw I could make the back extra strong as the Lian Li case (not sure if all cases do this) as a naked bit on the rearside of the mobo which I used to tighten the screws that side. They're nice and tight now.
My room temp now (midnight) is 27.3C/81.1F
Any suggestions?
Please let it be a cool one (groan)
Thanks, GinZ
Comment