Tweet
My setup: Q6600 + GA-EP45-UD3P(bios9f) + 8GB (2GB x 4) DDR2 800MHX G.Skill
My problem: Unstable overclock, causes various app crashes including the most frequent explorer.exe and right click function.
My request: help me stabilize my overclock at 3.6 GHZ, which was my goal. I'll settle for 3.5 too.
My BIOS Specs: adjusted for overclock and Vista/ OS X Leopard dual boot are attached
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8x
CPU Frequency ...........................: 3.36GHz (420x8)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 420Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 900mV
CPU Clock Skew (ps)....................: 50ps
MCH Clock Skew (ps)...................: 150ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: [Not Exist on my bios]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: [2.00B]
Memory Frequency (Mhz) ..............: 840
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 5 Auto
tRCD ......................................... 5 Auto
tRP'........................................... 5 Auto
tRAS.......................................... 15
Advanced Timing Control
tRRD........................................... 3 Auto
tWTR.......................................... 4
tWR............................................ 4
tRFC........................................... 65
tRTP........................................... 4
Command Rate (CMD) ....................: 2
Driving Strength Profiles
Driving Strength ............................ 1066
Channel A
Static tRead Value.........................:9
tRD Phase0 Adjustment...................: 0 Auto
tRD Phase1 Adjustment...................: 0 Auto
tRD Phase2 Adjustment .................: 0 Auto
tRD Phase3 Adjustment..................: 0 Auto
Trd2rd(Different Rank)....................: 6 Auto
Twr2wr(Different Rank)...................: 6 Auto
Twr2rd(Different Rank)...................: 5 Auto
Trd2wr(Same/Diff Rank)..................: 8 Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR Write Training Control.............: Auto
Channel B
Static tRead Value.........................: 9
tRD Phase0 Adjustment...................: 0 Auto
tRD Phase1 Adjustment...................: 0 Auto
tRD Phase2 Adjustment .................: 0 Auto
tRD Phase3 Adjustment..................: 0 Auto
Trd2rd(Different Rank)....................: 6 Auto
Twr2wr(Different Rank)...................: 6 Auto
Twr2rd(Different Rank)...................: 5 Auto
Trd2wr(Same/Diff Rank)..................: 8 Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR Write Training Control.............: Auto
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
MCH/ICH
DRAM
Channel A Reference ............: [Auto]
Channel B Reference ............: [Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Enabled]
Init Display first......................: PEG
HDD S.M.A.R.T Capability................: [Enabled]
No-Execute Memory Protect...............: [Enabled]
Integrated Peripherals
USB Storage Function ..............[Enabled]
My problem: Unstable overclock, causes various app crashes including the most frequent explorer.exe and right click function.
My request: help me stabilize my overclock at 3.6 GHZ, which was my goal. I'll settle for 3.5 too.
My BIOS Specs: adjusted for overclock and Vista/ OS X Leopard dual boot are attached
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8x
CPU Frequency ...........................: 3.36GHz (420x8)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 420Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 900mV
CPU Clock Skew (ps)....................: 50ps
MCH Clock Skew (ps)...................: 150ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: [Not Exist on my bios]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: [2.00B]
Memory Frequency (Mhz) ..............: 840
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 5 Auto
tRCD ......................................... 5 Auto
tRP'........................................... 5 Auto
tRAS.......................................... 15
Advanced Timing Control
tRRD........................................... 3 Auto
tWTR.......................................... 4
tWR............................................ 4
tRFC........................................... 65
tRTP........................................... 4
Command Rate (CMD) ....................: 2
Driving Strength Profiles
Driving Strength ............................ 1066
Channel A
Static tRead Value.........................:9
tRD Phase0 Adjustment...................: 0 Auto
tRD Phase1 Adjustment...................: 0 Auto
tRD Phase2 Adjustment .................: 0 Auto
tRD Phase3 Adjustment..................: 0 Auto
Trd2rd(Different Rank)....................: 6 Auto
Twr2wr(Different Rank)...................: 6 Auto
Twr2rd(Different Rank)...................: 5 Auto
Trd2wr(Same/Diff Rank)..................: 8 Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR Write Training Control.............: Auto
Channel B
Static tRead Value.........................: 9
tRD Phase0 Adjustment...................: 0 Auto
tRD Phase1 Adjustment...................: 0 Auto
tRD Phase2 Adjustment .................: 0 Auto
tRD Phase3 Adjustment..................: 0 Auto
Trd2rd(Different Rank)....................: 6 Auto
Twr2wr(Different Rank)...................: 6 Auto
Twr2rd(Different Rank)...................: 5 Auto
Trd2wr(Same/Diff Rank)..................: 8 Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR Write Training Control.............: Auto
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled]
MCH/ICH
DRAM
Channel A Reference ............: [Auto]
Channel B Reference ............: [Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Enabled]
Init Display first......................: PEG
HDD S.M.A.R.T Capability................: [Enabled]
No-Execute Memory Protect...............: [Enabled]
Integrated Peripherals
USB Storage Function ..............[Enabled]
Comment