EP45T-UD3P and e8400 constant blue screens

[yohannus]

I had my computer running well before using a past template I found here, but I accidentally reset to defaults and i can't find that old template anymore. I think I should have posted my info anyways to get settings more specific to my setup. At this point, I dont really care too much about OCing. I just want the computer running atm.

CPU = e8400
Motherboard = ep45t-UD3P Rev. 1.0
BIOS Version = F7
Ram = Patriot Viper 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model PVS34G1600LLK timings : 7-7-7-20 1.9V

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9x
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.00
 
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [disabled] 
CPU Host Frequency (Mhz) ............: 333Mhz
PCI Express Frequency (Mhz) .........:auto
C.I.A.2 .................................:[Disabled]
 
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0
 
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.66D
Memory Frequency (Mhz) ..............: 1066 889
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 7
tRCD ......................................... 7
tRP'...........................................7
tRAS..........................................20
Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
Advanced Timing Control
tRRD...........................................4 auto
tWTR..........................................4 auto
tWR............................................8 auto
tRFC...........................................60 auto
tRTP...........................................4 auto
Command Rate (CMD) ....................:0  auto
Driving Strength Profiles
Driving Strength ............................
Channel A
Static tRead Value.........................:9
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
Channel B
Static tRead Value.........................:9
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
Motherboard Voltage Control
CPU
CPU Vcore�.���.........................:1.33125
CPU Termination�..... 1.200V*.......: << auto
CPU PLL�������....1.500V*.......: << auto
CPU Referen.����....0.760V*.......: <<< auto
CPU Reference2���,,0.760V*.......:<<< auto
MCH/ICH
MCH Core�����.....1.100V...........: << auto
MCH Reference�.��.0.760V...........; <<< Leave
MCH/DRAM Ref.�......0.900V...........: <<< Leave
ICH I/O������.....1.500V............: <<< Leave
ICH Core����...��1.100V............: <<< Leave
DRAM
DRAM Voltage ��....1.800V............: 1.700
DRAM Termination .�0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ..............[enabled] *Note* Must be enabled to flash from USB

These settings were taken off of some other posts... but the ram was different than my ram.... Please help me get my system running stable again... let me know if i need to post any more information...

Thanks

[Chike]

Re: EP45T-UD3P and e8400 constant blue screens

Please fill the template with your default values as well.
A screen capture of MemSet main(click >>) and SPD(click spd) windows would be helpful, you can download it from http://forums.tweaktown.com/f69/late...30/#post284762
Try increasing MCH Core graduately up to 1.24v.
Memory is running at much lower frequency than it's spec. Try 4.00B or 3.20B memory multipliers.
For these multiplier you need to set DRAM Voltage as specified by the manufacturer.

[yohannus]

Re: EP45T-UD3P and e8400 constant blue screens

Sorry about that here are default values as well.
The default values are right in front of "auto"...

I also made a few changes...
CPU host---400Mhz
memory multiplier---3.2B
MCHCore----1.18
DRAM voltage---1.9v

I can't get it to run at all on 4.0B.. probably because I'm such a newb at OCing.... thanks for any help...

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9x
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.00
 
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [disabled] 
CPU Host Frequency (Mhz) ............: 400Mhz
PCI Express Frequency (Mhz) .........:auto
C.I.A.2 .................................:[Disabled]
 
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0
 
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 3.2D
Memory Frequency (Mhz) ..............: 1066 1280
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 7
tRCD ......................................... 7
tRP'...........................................7
tRAS..........................................20
Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
Advanced Timing Control
tRRD...........................................4 auto
tWTR..........................................4 auto
tWR............................................8 auto
tRFC...........................................60 auto
tRTP...........................................4 auto
Command Rate (CMD) ....................:0  auto
Driving Strength Profiles
Driving Strength ............................
Channel A
Static tRead Value.........................:9
 tRD Phase0 Adjustment...................:  0  Auto 
tRD Phase1 Adjustment...................:   0  Auto  
 tRD Phase2 Adjustment .................:   0  Auto  
 tRD Phase3 Adjustment..................:   0  Auto  
Trd2rd(Different Rank)....................: 9  Auto  
Twr2wr(Different Rank)...................:  7  Auto   
Twr2rd(Different Rank)...................:  7  Auto   
Trd2wr(Same/Diff Rank)..................:   10 Auto    
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
Channel B
Static tRead Value.........................:9
 tRD Phase0 Adjustment...................:  0  Auto 
tRD Phase1 Adjustment...................:   0  Auto  
 tRD Phase2 Adjustment .................:   0  Auto  
 tRD Phase3 Adjustment..................:   0  Auto  
Trd2rd(Different Rank)....................: 9  Auto  
Twr2wr(Different Rank)...................:  7  Auto   
Twr2rd(Different Rank)...................:  7  Auto   
Trd2wr(Same/Diff Rank)..................:   10 Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
Motherboard Voltage Control
CPU
CPU Vcore�.���.........................:1.33125
CPU Termination�..... 1.200V*.......: << 1.200v auto
CPU PLL�������....1.500V*.......: << 1.500v  auto
CPU Referen.����....0.760V*.......: <<< .760v  auto
CPU Reference2���,,0.750V*.......:<<< .750v   auto
MCH/ICH
MCH Core�����.....1.100V...........: << 1.18v  auto
MCH Reference�.��.0.760V...........; <<< .760v  Leave
MCH/DRAM Ref.�......0.900V...........: <<< .750v Leave
ICH I/O������.....1.500V............: <<< 1.500v Leave
ICH Core����...��1.100V............: <<< 1.100v  Leave
DRAM
DRAM Voltage ��....1.800V............: 1.900 v
DRAM Termination .�0.900V............: <<< .750v  Leave
Channel A Reference 0.900V............: <<< .750v Leave
Channel B Reference 0.900V............: <<< .750v Leave
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ..............[enabled] *Note* Must be enabled to flash from USB

[Chike]

Re: EP45T-UD3P and e8400 constant blue screens

Timings in the template don't match MemSet screen, are they auto?

You have PVS34G1333LLK as memory part number in your sig, but MemSet SPD shows "1600LL Series" and it has XMP 800 profile (DDR-1600).

Set Static tRead Value 10-12 for both channels, lower it later when you manage to get things stable.
You have 3.33D multiplier, you can try that, and more MCH Core up to 1.24/1.26v.

You said you don't care about OCing, plans have changed? what CPU cooler do you have?

Please list value or auto, which ever applies, nex time you post settings, and remove the "leave"s.
Default values to the left of the colons, auto or manually set values to the right.
Reference voltages and DRAM Termination should be left on auto unless you need to change them.
Vcore, CPU PLL, CPU Termination need not to be left on auto when OCing, see this post.

[yohannus]

Re: EP45T-UD3P and e8400 constant blue screens

Sorry about the hassle chike... thanks for being patient with me...
hopefully the third time is the charm...
I think I put down the wrong memory for my sig as the 1600LL is the memory that I have.
I ended up finishing the video that I needed to edit on another computer, so yes plans have changed, I want to try to get this thing moderately OCed...
I have a Zalman CNPS9500AT cpu fan... I have not had trouble with overheating on my old motherboard... even when overclocked...
This is the same as the last setup, just cleaned up. The memset shot is the same as the last post.

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0
 
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 3.2D
Memory Frequency (Mhz) ..............: 1066 1280
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 7 : auto
tRCD ......................................... 7 : auto
tRP'...........................................7 : auto
tRAS..........................................20 : auto
Set all Suggested below to highest Values first.  Then later you can lower, one at a time, 

testing as you go
Advanced Timing Control
tRRD...........................................4 auto
tWTR..........................................4 auto
tWR............................................8 auto
tRFC...........................................60 auto
tRTP...........................................4 auto
Command Rate (CMD) ....................:0  auto
Driving Strength Profiles
Driving Strength ............................
Channel A
Static tRead Value.........................:9
 tRD Phase0 Adjustment...................0 : Auto 
tRD Phase1 Adjustment...................0 : Auto  
 tRD Phase2 Adjustment .................0 :  Auto  
 tRD Phase3 Adjustment..................0 : Auto  
Trd2rd(Different Rank)....................9 : Auto  
Twr2wr(Different Rank)...................7 : Auto   
Twr2rd(Different Rank)...................7 : Auto   
Trd2wr(Same/Diff Rank)..................10 :Auto    
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
Channel B
Static tRead Value.........................:9
 tRD Phase0 Adjustment...................0 : Auto 
tRD Phase1 Adjustment...................0 : Auto  
 tRD Phase2 Adjustment .................0 :  Auto  
 tRD Phase3 Adjustment..................0 : Auto  
Trd2rd(Different Rank)....................9 : Auto  
Twr2wr(Different Rank)...................7 : Auto   
Twr2rd(Different Rank)...................7 : Auto   
Trd2wr(Same/Diff Rank)..................10 :Auto    
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
Motherboard Voltage Control
CPU
CPU Vcore�.���.........................:1.33125
CPU Termination�..... 1.200V.......: << auto
CPU PLL�������....1.500V.......: <<  auto
CPU Referen.����....0.760V.......: <<<  auto
CPU Reference2���,,0.750V.......:<<<   auto
MCH/ICH
MCH Core�����..............1.100V  : << 1.18v  
MCH Reference�.��..........0.760V  : <<< auto
MCH/DRAM Ref.�.............0.750V  : <<< auto
ICH I/O������...............1.500V : <<< auto
ICH Core����...��............1.100V: <<< auto
DRAM
DRAM Voltage ��.....................: 1.900 v
DRAM Termination .�..........0.750V  : <<<  auto
Channel A Reference .........0.750V  : <<<  auto
Channel B Reference .........0.750V  : <<<  auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ..............[enabled] *Note* Must be enabled to flash from USB

[Chike]

Re: EP45T-UD3P and e8400 constant blue screens

hopefully the third time is the charm...

Almost, the settings above Advanced Clock Control, no worries, just remember for next time.
MemSet screen, especially the SPD window only needed once.
Set CPU Termination 1.2v manually, increase it if needed.
Set PLL 1.5v or one tick higher.

Have you ran any stress tests yet?