+200 BCLK GA-X58 ud5

[miguelone]

Hi all.
First, im not an english man, so my english is very bad.
I would like to ask how to put more than 200 BCLK on my mother.
Allways i put 200 or more, the system is bad.
I need a good configuration for my bios(f9e) to try it.
My config. now is:
191x21

QPI OLL 1.22
IOH Core 1.22
ICH I/O 1.5
ICH Core 1.14
PCIE 1.5
CPU Vcor 1.3000
CPU PLL 1.84
QPI/VTT 1.35

Is impossible to me to have 200x21 for 4.2

Thanks.

[miguelone]

Re: +200 BCLK GA-X58 ud5

Hi again.
I was trying with 4.2 config, and in few seconds with Prime 95 i have a system failure. Its normal, but [B]please, see the multi. at the photo just when system failure.




Help, please.

Thanks.

[/SIZE]

[wazza300]

Re: +200 BCLK GA-X58 ud5

<a href="http://tinypic.com" target="_blank"><img src="http://i45.tinypic.com/mkg1so.jpg" border="0" alt="Image and video hosting by TinyPic"></a>

<a href="http://tinypic.com" target="_blank"><img src="http://i46.tinypic.com/32zq53r.jpg" border="0" alt="Image and video hosting by TinyPic"></a>

here for 4.3 you might need to tweak cpu and qpi voltages

[miguelone]

Re: +200 BCLK GA-X58 ud5

wow, i will try to do it. Thanks.
my voltages are highest than yours.

[miguelone]

Re: +200 BCLK GA-X58 ud5

here for 4.3 you might need to tweak cpu and qpi voltages

<!-- / message --> <!-- sig --> __________________

[wazza300]

Re: +200 BCLK GA-X58 ud5

try with 1.3800 qpi and try looser ram timings try 8-8-8-26

[miguelone]

[wazza300]

Re: +200 BCLK GA-X58 ud5

uncore is 2 times memory multiplier and add 1 so if 8x2=16+1,i dont think you will run 7-8-7-20 @4.2 i dont know try with auto ram timings and just tweak the qpi and cpu voltages till your stable then tweak ram timings later

[miguelone]

Re: +200 BCLK GA-X58 ud5

,i dont think you will run 7-8-7-20 @4.2 i dont know try with auto ram timings and just tweak the qpi and cpu voltages till your stable then tweak ram timings later

I was do it, but no way.
I try to do more changes, and i will say you.

Thanks.

[miguelone]

Re: +200 BCLK GA-X58 ud5

No way again. i think was more stable changing another voltages.

[miguelone]

Re: +200 BCLK GA-X58 ud5

Hi again.
With this config. two minits with Prime 95 and system failure, but better than other configs.

Updated Bios to f9k
21X199
DRAM Frec. 1592 (x8)
Uncore x17
x36
CPU Vcore 1.32
QPI/VTT 1.380
PCIE 1.50
QPI PLL 1.2
IOH Core 1.22
ICH Core 1.14
DRAM Volt. 1.66
9-10-10-25

Help please.

[Lsdmeasap]

Re: +200 BCLK GA-X58 ud5

Please give me your full settings and specs in a template from my signature, then I can help.

[miguelone]

Re: +200 BCLK GA-X58 ud5

Hi again.

Advanced CPU Features:
CPU Clock Ratio ................................ [20x] 21
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled] Disabled
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled]
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... (Always 2x memory Multi or 2x +1) x17
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................199
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard] Expert
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO] x8
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................9
tRCD .......................................10
tRP .........................................10
tRAS .......................................25

Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel A Misc Timing Control##
Round Trip Latency ...................



Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled]
CPU Vcore ...............................1.33
QPI/VTT Voltage 1.150v ............ 1.380
CPU PLL 1.800v ....................... 1.84

MCH/ICH
PCIE 1.500v ........................... 1.500
QPI PLL 1.100v ....................... 1.2
IOH Core 1.100v ..................... 1.22
ICH I/O 1.500v ....................... 1.500
ICH Core 1.1v ........................ 1.14

DRAM 1592
DRAM Voltage 1.500v .............. 1.66
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

Thanks.

Note: with prime95, system freeze, but not restart.(no bsod)

[Lsdmeasap]

Re: +200 BCLK GA-X58 ud5

Thanks, try these


I do need a link to your memory though or the model # before I can best advise you

Advanced CPU Features:
CPU Clock Ratio ................................ [20x] 21
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled] Disabled
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled]
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... (Always 2x memory Multi or 2x +1) x17 << Try x18, some CPU's do not like Odd values here
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................199
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard] Expert
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO] x8
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................9
tRCD .......................................10
tRP .........................................10
tRAS .......................................25

Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel A Misc Timing Control##
Round Trip Latency ...................



Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled] << Enabled
CPU Vcore ...............................1.33 << Try a bit more
QPI/VTT Voltage 1.150v ............ 1.380 << May need 1.4-1.45+
CPU PLL 1.800v ....................... 1.84

MCH/ICH
PCIE 1.500v ........................... 1.500
QPI PLL 1.100v ....................... 1.2 << May need 1.24-1.3
IOH Core 1.100v ..................... 1.22 << may need 1.24+
ICH I/O 1.500v ....................... 1.500
ICH Core 1.1v ........................ 1.14

DRAM 1592
DRAM Voltage 1.500v .............. 1.66
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

Please do get me a link to your memory, as I doubt you need to use loose timings like you are now. 9-10-10-25 should not be needed at all, I assume you have them set like this for testing or to try and get things going, but you should not need to.

[miguelone]

Re: +200 BCLK GA-X58 ud5

Hi again

my bios settings

Advanced CPU Features:
CPU Clock Ratio ................................ [20x] 21
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled] Disabled
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled]
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency .......................... (Always 2x memory Multi or 2x +1) 7 << Try x18, some CPU's do not like Odd values here x18
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................199
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard] Expert
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO] x8
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................9
tRCD .......................................10
tRP .........................................10
tRAS .......................................25

Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel A Misc Timing Control##
Round Trip Latency ...................



Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled] << Enabled
CPU Vcore ...............................1.33 << Try a bit more 1.376(cpu-z)
QPI/VTT Voltage 1.150v ............ 1.380 << May need 1.4-1.45+ 1.42
CPU PLL 1.800v ....................... 1.84

MCH/ICH
PCIE 1.500v ........................... 1.500
QPI PLL 1.100v ....................... 1.2 << May need 1.24-1.3 1.3
IOH Core 1.100v ..................... 1.22 << may need 1.24+ 1.26
ICH I/O 1.500v ....................... 1.500 1.5
ICH Core 1.1v ........................ 1.14 1.16

DRAM 1592
DRAM Voltage 1.500v .............. 1.66
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]


My ram are Mushkin radioactive 12800 7-8-7-20 cl7

They are on 9-10-10-25 to try first the cpu OC.

No way with this configuration and with anyone, grrrrrrrrrrrrrrrrrrrrrrrrrr


Help, please.

Thanks.