GIGABYTE GA-EP45-UD3P Rev 1.6
Intel Core 2 Duo E7400 Wolfdale 2.8GHz
G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 2.0-2.1V
ARCTIC COOLING Freezer 7 Pro 92mm
Been running small ftt on prime for about 16 hours.
How are these voltages and temps for the e7400 @3.8
Temps after 12 hours for Core 0 and Core 1 were between 58-62 with Temp1 at 35 and Temp2 between 59-65.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: +0.5
CPU Frequency ...........................: 3.8Ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.66c
Memory Frequency (Mhz) ..............: 1066Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Channel A & B
Static tRead Value.........................: 8
Motherboard Voltage Control
Voltage Type.………... Manual
Load Line Calibration : ON
CPU Vcore….……….........................:1.43750
CPU Termination…..... 1.200V*.......: 1.30
CPU PLL…………………....1.500V*.......: 1.59V
CPU Referen.…………....0.755V*.......: 0.76
MCH/ICH
MCH Core…………….....1.100V...........: 1.20V
MCH Reference….…….0.800V...........; 0.76
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.550V............: 1.50V
ICH Core…………...……1.100V............: 1.10V
DRAM
DRAM Voltage ……....1.800V............: 2.00V
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Intel Core 2 Duo E7400 Wolfdale 2.8GHz
G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 2.0-2.1V
ARCTIC COOLING Freezer 7 Pro 92mm
Been running small ftt on prime for about 16 hours.
How are these voltages and temps for the e7400 @3.8
Temps after 12 hours for Core 0 and Core 1 were between 58-62 with Temp1 at 35 and Temp2 between 59-65.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................: +0.5
CPU Frequency ...........................: 3.8Ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.66c
Memory Frequency (Mhz) ..............: 1066Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Channel A & B
Static tRead Value.........................: 8
Motherboard Voltage Control
Voltage Type.………... Manual
Load Line Calibration : ON
CPU Vcore….……….........................:1.43750
CPU Termination…..... 1.200V*.......: 1.30
CPU PLL…………………....1.500V*.......: 1.59V
CPU Referen.…………....0.755V*.......: 0.76
MCH/ICH
MCH Core…………….....1.100V...........: 1.20V
MCH Reference….…….0.800V...........; 0.76
MCH/DRAM Ref.…......0.900V...........: Auto
ICH I/O……………….....1.550V............: 1.50V
ICH Core…………...……1.100V............: 1.10V
DRAM
DRAM Voltage ……....1.800V............: 2.00V
DRAM Termination .…0.900V............: Auto
Channel A Reference 0.900V............: Auto
Channel B Reference 0.900V............: Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Comment